Go Back   The Ford Barn > General Discussion > Model A (1928-31)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 01-24-2021, 04:17 AM   #1
Michael_Velling
Member
 
Join Date: Jan 2020
Location: Germany
Posts: 33
Default Piston and cylinder clearance / measurement???

Hello,

maybe i dont understand this correct

I have to buy new pistons and the machineshop here in germany have to bore the cylinders correctly, but in germany no one who knows the correct clearance or diameter. Can you help?

Standard Piston Diameter = 3,8745 Inch
Piston 0,0600 Oversize from Macs = 3,9345 Inch
Right?

Cylinder bore Standard = 3,876 Inch ???
Cylinder bore for Oversize = 3,936 Inch ???

How much must the cylinder "bigger" then the piston? I found a source that tells: 0,015 Inch ???

I think that is very tight, or not?

Thanks a lot for information
__________________
Greetings

Michael
------
Toenisvorst, Germany
Michael_Velling is offline   Reply With Quote
Old 01-24-2021, 07:50 AM   #2
Dave in MN
Senior Member
 
Dave in MN's Avatar
 
Join Date: May 2010
Location: Jordan, MN
Posts: 1,410
Default Re: Piston and cylinder clearance / measurement???

Michael,
I rebuild Model A and B engines. For an engine that is built for standard service, I hone the cylinders to provide a minimum of .0035" clearance. If the engine is to be used as a touring engine and will see duty under prolonged runs at higher speeds, I hone to .004" clearance. I also slightly increase the clearance on #3 and #4 cylinders as, from my experience, I think they are a bit more prone to scoring. 2 tenths of a thousandths is sufficient increase for these two rear cylinders.
Good Day!
Dave in MN

www.durableperformance.net

Last edited by Dave in MN; 01-25-2021 at 11:32 AM.
Dave in MN is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 01-24-2021, 07:57 AM   #3
Patrick L.
Senior Member
 
Patrick L.'s Avatar
 
Join Date: May 2010
Location: Largo Florida
Posts: 7,225
Default Re: Piston and cylinder clearance / measurement???

I think you meant .0015", which is too tight.

The piston maker will have its clearance spec.

I like to run them looser. I prefer a bit loose to a bit tight. The standard is .001" per inch of bore. In an 'A' I like at least .004" if not .005"
Patrick L. is offline   Reply With Quote
Old 01-24-2021, 08:01 AM   #4
Rodrelic
Senior Member
 
Join Date: Mar 2018
Location: Florida panhandle
Posts: 194
Default Re: Piston and cylinder clearance / measurement???

The Model A Ford Restorers org has specifications page shows a difference of .0015 of stock bore/piston.
https://model-a-ford.org/resources/t...pecifications/
Rodrelic is offline   Reply With Quote
Old 01-24-2021, 08:39 AM   #5
Dave in MN
Senior Member
 
Dave in MN's Avatar
 
Join Date: May 2010
Location: Jordan, MN
Posts: 1,410
Default Re: Piston and cylinder clearance / measurement???

Quote:
Originally Posted by Rodrelic View Post
The Model A Ford Restorers org has specifications page shows a difference of .0015 of stock bore/piston.
https://model-a-ford.org/resources/t...pecifications/
Rodrelic,
From the link you provide, I can't find the reference you refer to that states a clearance of.0015" between piston and bore. I speculate these numbers could be for split skirt pistons. The solid skirt pistons currently available require more clearance than .0015".

I have repaired a number of engines using solid skirt pistons that did not have sufficient clearance. Scored pistons and scratched cylinder walls are the found problem along with all the metal shards in the bearings....expensive.

One of my customers made a statement after I repaired his engine:
"If they had opened up the clearance then, (when the engine was built) I wouldn't be opening my wallet now." True.
Good Day,
Dave
Dave in MN is offline   Reply With Quote
Old 01-24-2021, 09:49 AM   #6
Michael_Velling
Member
 
Join Date: Jan 2020
Location: Germany
Posts: 33
Default Re: Piston and cylinder clearance / measurement???

Sponsored Links (Register now to hide all advertisements)
Hello,

Thanks to all of you.

Tommorow i go to the machine shop an we will measure the cylinders. Then i order pistons and so on at snyders. After the pistons are in Germany the machine shop have to measure the diameter of the oversize pistons.

And now....

The cylinder bore must be 0,0035 to 0,0040 larger then the new pistons.

Correct?

Gesendet von meinem SM-T815 mit Tapatalk
__________________
Greetings

Michael
------
Toenisvorst, Germany
Michael_Velling is offline   Reply With Quote
Old 01-24-2021, 10:39 AM   #7
johnneilson
Senior Member
 
Join Date: Jun 2010
Location: 34.22 N 118.36 W
Posts: 1,043
Default Re: Piston and cylinder clearance / measurement???

The Model A engine still has the physics of material thermal expansion.
The original pistons have a "split skirt" this means that the piston has a cut that allows the skirt to compress or expand. This type of piston can survive with the 0.0015 in. clearance.

Modern pistons are made without the relief cut and require more clearance.
There are quite a few variables but, typical clearances are 0.001 to .002 per inch of bore size.

The only advice I can offer is to follow the directions for clearance that the pistons come with.

John
__________________
As Carroll Smith wrote; All Failures are Human in Origin.
johnneilson is offline   Reply With Quote
Old 01-24-2021, 11:05 AM   #8
katy
Senior Member
 
katy's Avatar
 
Join Date: Jun 2015
Location: Red Deer, Alberta
Posts: 5,004
Default Re: Piston and cylinder clearance / measurement???

Quote:
Originally Posted by Michael_Velling View Post
Hello,

And now....

The cylinder bore must be 0,0035 to 0,0040 larger then the new pistons.

Correct?

Gesendet von meinem SM-T815 mit Tapatalk
You got it.

Modern engines have water jackets that are the length of the cylinder. Model A engines only have water jackets for part of the cylinder, necessitating that the pistons in a Model A engine require more clearance than a modern engine.
__________________
If you don't hear a rumor by 10 AM, start one!.
Got my education out behind the barn!
katy is offline   Reply With Quote
Old 01-24-2021, 12:17 PM   #9
BRENT in 10-uh-C
Senior Member
 
BRENT in 10-uh-C's Avatar
 
Join Date: May 2010
Location: Eastern Tennessee
Posts: 11,485
Default Re: Piston and cylinder clearance / measurement???

Quote:
Originally Posted by katy View Post
You got it.

Modern engines have water jackets that are the length of the cylinder. Model A engines only have water jackets for part of the cylinder, necessitating that the pistons in a Model A engine require more clearance than a modern engine.
How hot does it get down at the bottom of the cylinder? I have never known it to be any hotter there than what the crankcase area is. What am I missing, and what excessively heats up that area?
__________________
.

BRENT in 10-uh-C
.
www.model-a-ford.com
...(...Finally Updated!! )

.
BRENT in 10-uh-C is offline   Reply With Quote
Old 01-24-2021, 01:22 PM   #10
Jim Brierley
Senior Member
 
Join Date: Jun 2010
Location: Temecula, CA
Posts: 4,066
Default Re: Piston and cylinder clearance / measurement???

Johnneilson has explained it correctly. I bore the block to .003" oversize and hone another .0005". (.0035" total) Always have the new pistons in hand before boring the block, to be certain of the clearances. If you are going to run the engine hard, give them .004". Not necessary to allow for more clearance at the rear of the block, however it is a good idea to clean the water jackets to get rid of 90 years worth of rust. You can turn the block upside-down on an engine stand and use a piece of speedometer cable or wire rope to mechanically loosen all the crud and let gravity remove it from the block.
Jim Brierley is offline   Reply With Quote
Old 01-24-2021, 04:23 PM   #11
700rpm
Senior Member
 
700rpm's Avatar
 
Join Date: May 2010
Location: Portland, Oregon
Posts: 5,892
Default Re: Piston and cylinder clearance / measurement???

Quote:
Originally Posted by Jim Brierley View Post
Johnneilson has explained it correctly. I bore the block to .003" oversize and hone another .0005". (.0035" total) Always have the new pistons in hand before boring the block, to be certain of the clearances. If you are going to run the engine hard, give them .004". Not necessary to allow for more clearance at the rear of the block, however it is a good idea to clean the water jackets to get rid of 90 years worth of rust. You can turn the block upside-down on an engine stand and use a piece of speedometer cable or wire rope to mechanically loosen all the crud and let gravity remove it from the block.
This is the best advice. The pistons I got from Snyders had a smaller suggested oversize. I used their specs, and had to pull the engine and have it rebored because it was too tight, overheated, and would lock up till it cooled. It’s been several years, but I think I ended up with .0045 with sleeved back to standard cylinders.
__________________
Ray Horton, Portland, OR


As you go through life, keep your eye on the donut, not the hole.
700rpm is offline   Reply With Quote
Old 01-25-2021, 11:11 AM   #12
Flathead
Senior Member
 
Flathead's Avatar
 
Join Date: May 2010
Location: Southern Maine
Posts: 1,492
Default Re: Piston and cylinder clearance / measurement???

The popular, foreign made pistons sold by most of the suppliers call for .003 clearance. That is too tight for these pistons, they are solid skirt and they mistakenly give the spec that is used for a split skirt piston which is a different animal. They need to be set up looser as has been suggested here.
Flathead is offline   Reply With Quote
Old 01-25-2021, 02:58 PM   #13
briphaeton
Senior Member
 
Join Date: Jan 2012
Posts: 241
Default Re: Piston and cylinder clearance / measurement???

Does Forged pistons require more clearance?
briphaeton is offline   Reply With Quote
Old 01-25-2021, 04:48 PM   #14
Flathead
Senior Member
 
Flathead's Avatar
 
Join Date: May 2010
Location: Southern Maine
Posts: 1,492
Default Re: Piston and cylinder clearance / measurement???

Generally yes, I would follow the manufacturer's specs in this case.
Flathead is offline   Reply With Quote
Old 01-25-2021, 05:29 PM   #15
Patrick L.
Senior Member
 
Patrick L.'s Avatar
 
Join Date: May 2010
Location: Largo Florida
Posts: 7,225
Default Re: Piston and cylinder clearance / measurement???

Quote:
Originally Posted by briphaeton View Post
Does Forged pistons require more clearance?




Yep
Patrick L. is offline   Reply With Quote
Old 01-26-2021, 03:20 PM   #16
Jim Brierley
Senior Member
 
Join Date: Jun 2010
Location: Temecula, CA
Posts: 4,066
Default Re: Piston and cylinder clearance / measurement???

I run .010" on my Bonneville engine with forged pistons.
Jim Brierley is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 07:28 AM.