Go Back   The Ford Barn > General Discussion > Model A (1928-31)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 07-25-2020, 11:50 AM   #1
Licensed to kill
Senior Member
 
Licensed to kill's Avatar
 
Join Date: Aug 2016
Location: Alberta
Posts: 930
Default Decided to pull the motor/trans

So, I had done the valves and guides (they were shot) in hopes of fixing an oil consumption problem (1qt in 60 miles) to no avail. It ran sweet but still uses the same amount of oil. So, I pulled the head and dropped the pan so I could pull the pistons and check them out. When I had the head off to do the valves, I noticed that the cylinders were glazed but there was no ridge so was thinking a deglazing and new rings should do the trick. Nope. Has .0100 over pistons (for a 3.975 bore) and the bores mic'ed 3.986 and the rings had a gap of 1/8-3/16". There was also some scoring on the walls and pistons, mostly at the bottom of the cylinders. So, after some pondering, I decided to hone the cylinders out to 4" and put .0125 over pistons in. I did #1 cylinder in the car but found that the amount of metal dust produced was such that there was NO WAY I would be able to clean the bottom end sufficiently so I pulled the engine/trans to do it on the stand. In so doing, I found a few other issues that need to be dealt with. The oddest one was that one motor mount was broken. The face that bolts to the block was broke straight across the middle then up and around the edge so that the top bolt was not holding anything, just the broken square from the mount. NO IDEA how that could/would break that way. Also, the pressure plate fingers wee WAY out of whack (possibly explaining the clutch chatter when taking off). Two fingers were 1/8" plus lower than the others. A screw was missing from the bottom generator mount and the other was loose. Also found that the teeth on the ring gear are chewed but they are chewed on the backside which suggests to me that the ring gear was turned around as I would think that any grinding should occur on the front edge of the teeth where the bendix engages. It never made any noise when cranking so I think I will just leave that for now. Cylinders also had a wicked taper which takes some doing to remover (about .008 tighter at the bottom). Anyway, I'm going to try to set my clearances with a micrometer since the engine is out and on the stand. Mic the journal, then mic the corresponding "circle" and adjust for .0015 difference. The cam shows, what looks to me like, a fair amount of wear. The clutch disc looks OK but is solid. Not sure if it's worth putting a new spring damped disc in or not.
Licensed to kill is offline   Reply With Quote
Old 07-25-2020, 12:03 PM   #2
Patrick L.
Senior Member
 
Patrick L.'s Avatar
 
Join Date: May 2010
Location: Largo Florida
Posts: 7,225
Default Re: Decided to pull the motor/trans

Valve guides in any engine will not cause that much oil consumption. Ringing it properly is a good thing. But, with .008" taper I would recommend sending it out for boring. I prefer to leave the piston clearances a bit on the wide/loose side. But, thats just me.
Patrick L. is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 07-25-2020, 01:51 PM   #3
Licensed to kill
Senior Member
 
Licensed to kill's Avatar
 
Join Date: Aug 2016
Location: Alberta
Posts: 930
Default Re: Decided to pull the motor/trans

Quote:
Originally Posted by Patrick L. View Post
Valve guides in any engine will not cause that much oil consumption. Ringing it properly is a good thing. But, with .008" taper I would recommend sending it out for boring. I prefer to leave the piston clearances a bit on the wide/loose side. But, thats just me.
I already removed the taper and brought the cylinders to 4" (the pistons mic 3.998). well, 3 are done, one to go.
Licensed to kill is offline   Reply With Quote
Old 07-25-2020, 12:20 PM   #4
Jack Shaft
BANNED
 
Join Date: Dec 2019
Posts: 1,196
Default Re: Decided to pull the motor/trans

At 37 bucks change the clutch disc every time,especially if it chatters.generally when the cylinder bores are worn and the valve guides are shot every other component is worn..bearings,distributor drive,oil pump,everything should get a full inspection.
Jack Shaft is offline   Reply With Quote
Old 07-25-2020, 01:59 PM   #5
Licensed to kill
Senior Member
 
Licensed to kill's Avatar
 
Join Date: Aug 2016
Location: Alberta
Posts: 930
Default Re: Decided to pull the motor/trans

Quote:
Originally Posted by Jack Shaft View Post
At 37 bucks change the clutch disc every time,especially if it chatters.generally when the cylinder bores are worn and the valve guides are shot every other component is worn..bearings,distributor drive,oil pump,everything should get a full inspection.
already checked out the oil pump and distributor drive, all good. Bearings look good and of course will have the clearances set on assembly. Timing gears are good but cam shows wear. Cam bearings feel good. Release bearing and pilot bearing appear new. Good point on the disc. ordering it will delay assembly but I have a lot of detail work I can do while I wait. What I find odd is that the cylinders APPEAR to be worn (based on measurements) but there was zero ridge at the top of the cylinders leading me to think that maybe someone botched a bore job. I can't think of any way that a cylinder can wear that much and not leave a ridge.
Licensed to kill is offline   Reply With Quote
Old 07-25-2020, 02:08 PM   #6
100IH
Senior Member
 
Join Date: Dec 2011
Location: SW Idaho
Posts: 970
Default Re: Decided to pull the motor/trans

Sponsored Links (Register now to hide all advertisements)
I'll deal with only one item. The ring gear needs the rounded side of the teeth at the rear as it sits in the chassis. When you remove the starter the bendix goes past the ring gear and comes forward to engage, the rounded end of each tooth aids in engaging. same for the bendix, rounded end is the engage side.
100IH is offline   Reply With Quote
Old 07-25-2020, 03:25 PM   #7
Licensed to kill
Senior Member
 
Licensed to kill's Avatar
 
Join Date: Aug 2016
Location: Alberta
Posts: 930
Default Re: Decided to pull the motor/trans

Quote:
Originally Posted by 100IH View Post
I'll deal with only one item. The ring gear needs the rounded side of the teeth at the rear as it sits in the chassis. When you remove the starter the bendix goes past the ring gear and comes forward to engage, the rounded end of each tooth aids in engaging. same for the bendix, rounded end is the engage side.
Ah yes, I see that now. I never paid much attention. It's "backwards" from what I am used to. I'll change out the gear. Thanks
Licensed to kill is offline   Reply With Quote
Old 07-25-2020, 03:27 PM   #8
Licensed to kill
Senior Member
 
Licensed to kill's Avatar
 
Join Date: Aug 2016
Location: Alberta
Posts: 930
Default Re: Decided to pull the motor/trans

I see I have some up and down movement in the input shaft in the trans. Don't know what that means But I'm going to tear the tranny down and look things over while everything is out.
Licensed to kill is offline   Reply With Quote
Old 07-25-2020, 03:57 PM   #9
Jack Shaft
BANNED
 
Join Date: Dec 2019
Posts: 1,196
Default Re: Decided to pull the motor/trans

Engine doesn't have cam bearings,up and down play on the trans input shaft is normal,the pilot bearing in the flywheel supports it. Good news about the bearings,thats expensive work saved
Jack Shaft is offline   Reply With Quote
Old 07-25-2020, 06:46 PM   #10
Licensed to kill
Senior Member
 
Licensed to kill's Avatar
 
Join Date: Aug 2016
Location: Alberta
Posts: 930
Default Re: Decided to pull the motor/trans

Tore the tranny down. Gears are rounded on the tips and one tooth on one (don't recall which one) has a small chip. Not sure what to do there. $1000 for all new guts for a car that will see MAYBE 1000 miles a year???. Trans works well but would jump out of second when pulling. Hate to put it back together as is but...........I've got tomorrow to ponder and look them over again. Interesting note, Rather than two roller bearings and a spacer in the cluster it had three roller bearings. two short and one long. Also, rather than snap rings to hold the main bearings, there is a ridge cast into the case. Sure this is a model year thing just don't know enough about these to know what year.
Licensed to kill is offline   Reply With Quote
Old 08-08-2020, 10:20 AM   #11
GerryAllen
Senior Member
 
Join Date: May 2018
Location: Birch Bay WA
Posts: 190
Default Re: Decided to pull the motor/trans

Quote:
Originally Posted by Licensed to kill View Post
Tore the tranny down. Gears are rounded on the tips and one tooth on one (don't recall which one) has a small chip. Not sure what to do there. $1000 for all new guts for a car that will see MAYBE 1000 miles a year???. Trans works well but would jump out of second when pulling. Hate to put it back together as is but...........I've got tomorrow to ponder and look them over again. Interesting note, Rather than two roller bearings and a spacer in the cluster it had three roller bearings. two short and one long. Also, rather than snap rings to hold the main bearings, there is a ridge cast into the case. Sure this is a model year thing just don't know enough about these to know what year.
Why drive it only a 1000 miles a year. I drive mine between 5000 & 6000 miles a year, drive it enjoy it and you will get way more life out of it between repairs.
GerryAllen is offline   Reply With Quote
Old 08-08-2020, 02:23 PM   #12
Licensed to kill
Senior Member
 
Licensed to kill's Avatar
 
Join Date: Aug 2016
Location: Alberta
Posts: 930
Default Re: Decided to pull the motor/trans

Quote:
Originally Posted by GerryAllen View Post
Why drive it only a 1000 miles a year.
Because our work takes up most of the summer leaving VERY little "me" time and what little time i do get is divided between a few different toys. I addition to this Model A fordor, I have the Model A truck in my avatar, a '57 Chevy short step BBW pickup, a .28 model A sedan and a Solstice to drive in the summer. Last summer I licensed the Solstice, '57 truck and Model A truck and was only able to put less than 1000 mile between the three of them. This year I licensed the Model A fordor, '57 truck and Solstice and have put 1 drive on the Solstice (about 100 miles), a few drives on the '57 (maybe 300 miles) and 800 miles on the fordor. In a couple weeks work will start back up and that will be it for the toys for this year. I drive one of them every chance i get, just not a lot of chances.
Licensed to kill is offline   Reply With Quote
Old 07-26-2020, 02:51 AM   #13
Floats
Senior Member
 
Floats's Avatar
 
Join Date: Dec 2013
Location: Mossel Bay, about 300km from Cape Town
Posts: 530
Default Re: Decided to pull the motor/trans

Jumping out of gear will only get worse. Fix it while it is out.
__________________
Regards
Chris
Cape Town
28 Model A RPU, 29 Chevy Phaeton, 67 E Type FHC, 67 250SL Pagoda, 83 911 SC
Floats is offline   Reply With Quote
Old 07-26-2020, 07:39 AM   #14
Licensed to kill
Senior Member
 
Licensed to kill's Avatar
 
Join Date: Aug 2016
Location: Alberta
Posts: 930
Default Re: Decided to pull the motor/trans

Quote:
Originally Posted by Floats View Post
Jumping out of gear will only get worse. Fix it while it is out.
I can't seem to see anything that will cause it. Makes it hard to "fix".
Licensed to kill is offline   Reply With Quote
Old 07-26-2020, 12:23 PM   #15
Big hammer
Senior Member
 
Join Date: Jun 2014
Location: Land of Lincoln
Posts: 3,114
Default Re: Decided to pull the motor/trans

Quote:
Originally Posted by Licensed to kill View Post
I can't seem to see anything that will cause it. Makes it hard to "fix".
Check the dent plungers and spring, the plungers need to slide freely.
__________________
Don't force it with a little hammer tap, tap, tap
get a bigger hammer tap done
Big hammer is offline   Reply With Quote
Old 07-26-2020, 09:48 AM   #16
katy
Senior Member
 
katy's Avatar
 
Join Date: Jun 2015
Location: Red Deer, Alberta
Posts: 5,011
Default Re: Decided to pull the motor/trans

Quote:
I can't think of any way that a cylinder can wear that much and not leave a ridge.
Model T's do that, the top ring comes right to the top of the cylinder w/the piston sticking up above the block. Maybe the pistons you removed are like that?

Quote:
I already removed the taper and brought the cylinders to 4" (the pistons mic 3.998). well, 3 are done, one to go.
Is .002" piston clearance enough on these engines?
__________________
If you don't hear a rumor by 10 AM, start one!.
Got my education out behind the barn!

Last edited by katy; 07-26-2020 at 09:49 AM. Reason: Corrected typo
katy is offline   Reply With Quote
Old 07-26-2020, 10:06 AM   #17
Licensed to kill
Senior Member
 
Licensed to kill's Avatar
 
Join Date: Aug 2016
Location: Alberta
Posts: 930
Default Re: Decided to pull the motor/trans

Quote:
Originally Posted by katy View Post
Model T's do that, the top ring comes right to the top of the cylinder w/the piston sticking up above the block. Maybe the pistons you removed are like that?



Is .002" piston clearance enough on these engines?
The pistons are level with the deck @TDC so the top ring will be down a bit from that. I thought .002 was a bit tight also but that is the spec that I found and I looked for verification from a few different sources. All say .002.
Licensed to kill is offline   Reply With Quote
Old 07-26-2020, 12:31 PM   #18
Big hammer
Senior Member
 
Join Date: Jun 2014
Location: Land of Lincoln
Posts: 3,114
Default Re: Decided to pull the motor/trans

Quote:
Originally Posted by katy View Post
Model T's do that, the top ring comes right to the top of the cylinder w/the piston sticking up above the block. Maybe the pistons you removed are like that?



Is .002" piston clearance enough on these engines?
NO! #3&#4 with the larger bores at 4inches need .004 clearance. The two back clylinders run hotter than the front two. I would make all four .004 clearance, Someone had problems with his engine seizing, after several tear downs he increased the bore clearances to .004 and his problem was solved.
__________________
Don't force it with a little hammer tap, tap, tap
get a bigger hammer tap done
Big hammer is offline   Reply With Quote
Old 07-26-2020, 12:34 PM   #19
Licensed to kill
Senior Member
 
Licensed to kill's Avatar
 
Join Date: Aug 2016
Location: Alberta
Posts: 930
Default Re: Decided to pull the motor/trans

Quote:
Originally Posted by Big hammer View Post
NO! #3 with the larger bores at 4inches need .004 clearance. The two back clylinders run hotter than the front two. I would make all four .004 clearance, Someone had problems with his engine seizing, after several tear downs he increased the bore clearances to .004 and his problem was solved.
Sounds reasonable. I haven't done the final finish hone yet so can easily add a thou or two. It would actually make me feel better anyway as .002 seems pretty tight to me. Thanks
Licensed to kill is offline   Reply With Quote
Old 08-08-2020, 02:05 AM   #20
Brendan1959
Member
 
Brendan1959's Avatar
 
Join Date: Jul 2010
Location: Melbourne Australia
Posts: 95
Default Re: Decided to pull the motor/trans

Quote:
Originally Posted by Licensed to kill View Post
Sounds reasonable. I haven't done the final finish hone yet so can easily add a thou or two. It would actually make me feel better anyway as .002 seems pretty tight to me. Thanks
What sort of hone are you using? I did not think you could go up a size with just a hone, not criticizing, it is the sort of thing I would like to do.

Brendan
Brendan1959 is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 04:56 AM.