Go Back   The Ford Barn > General Discussion > Model A (1928-31)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 10-31-2019, 05:56 PM   #1
Ruth
Senior Member
 
Join Date: May 2016
Location: Glide, Oregon
Posts: 1,334
Default Cotter pins

A question was posed to me and I have no idea what the answer might be.

Did Ford use galvanized cotter pins back when or did he save money and use carbon steel cotter pins?

Thanks.
Ruth is offline   Reply With Quote
Old 10-31-2019, 06:01 PM   #2
figment
Senior Member
 
Join Date: May 2010
Posts: 332
Default Re: Cotter pins

He used cadmium plating
figment is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 10-31-2019, 11:44 PM   #3
CWPASADENA
Senior Member
 
CWPASADENA's Avatar
 
Join Date: May 2010
Location: PASADENA, CA
Posts: 1,882
Default Re: Cotter pins

Originally, Henry used cotter pins with no finish.


Chris W.
CWPASADENA is offline   Reply With Quote
Old 11-01-2019, 07:52 AM   #4
jhowes
Senior Member
 
Join Date: Jul 2010
Location: upstate NY near Mass border
Posts: 789
Default Re: Cotter pins

I would like to ask another question on this subject. Are the stainless cotter pins strong enough? I have never known if the stainless bolts are as strong as the grade five bolts for example.
jhowes is offline   Reply With Quote
Old 11-01-2019, 08:44 AM   #5
alexiskai
Senior Member
 
alexiskai's Avatar
 
Join Date: Apr 2018
Location: Mebane NC
Posts: 2,332
Default Re: Cotter pins

Since the whole point of cotter pins is that you can bend them with pliers, or often just your thumb, I would consider their strength to be minimal. You could probably make them out of plastic if you wanted. Their job is to prevent the nut from working loose due to vibration, there's virtually no strength required for that.

Edit: There is a valid debate about whether it's a good idea to re-use cotter pins since the act of setting/bending them fatigues the metal. I try not to re-use unless I don't have a suitable replacement. Not a hard-and-fast rule though.
alexiskai is offline   Reply With Quote
Old 11-01-2019, 09:51 AM   #6
DD931
Senior Member
 
DD931's Avatar
 
Join Date: May 2010
Location: PA Poconos
Posts: 723
Default Re: Cotter pins

Sponsored Links (Register now to hide all advertisements)
My dad straightened rusty nails and kept old screws - depression mentality. Times have changed. I would not recommend reusing a cotter pin!!
DD931 is offline   Reply With Quote
Old 11-01-2019, 09:56 AM   #7
katy
Senior Member
 
katy's Avatar
 
Join Date: Jun 2015
Location: Red Deer, Alberta
Posts: 5,011
Default Re: Cotter pins

In a past life, in a pinch, I've used a nail to replace a cotter pin. I'm sure jillions of others have done the same thing.
__________________
If you don't hear a rumor by 10 AM, start one!.
Got my education out behind the barn!
katy is offline   Reply With Quote
Old 11-01-2019, 11:57 AM   #8
jhowes
Senior Member
 
Join Date: Jul 2010
Location: upstate NY near Mass border
Posts: 789
Default Re: Cotter pins

My question was more toward the nuts and bolts. I have used stainless nuts and bolts where I don't want rust to be seen and wondered if the strength was the same as the standard steel bolts. Jack
jhowes is offline   Reply With Quote
Old 11-01-2019, 12:42 PM   #9
jw hash
Senior Member
 
jw hash's Avatar
 
Join Date: May 2010
Location: Auburn Washington
Posts: 2,550
Default Re: Cotter pins

Chris is correct. i have used stainless cotter keys. you would think they would be softer, but they are harder to bend. for the most part I used Cad or zinc plated cotter keys.
jw hash is offline   Reply With Quote
Old 11-01-2019, 12:51 PM   #10
Ak Sourdough
Senior Member
 
Ak Sourdough's Avatar
 
Join Date: Jul 2014
Location: Fairbanks, Alaska
Posts: 126
Default Re: Cotter pins

There are many grades of stainless bolts, just as there are with steel bolts. The ones you get at the big box store are usually as soft as a grade 2 steel bolt. You get what you pay for and stainless is expensive.
Ak Sourdough is offline   Reply With Quote
Old 11-01-2019, 01:11 PM   #11
holdover
Senior Member
 
Join Date: May 2011
Location: SW Virginia near the Blue ridge Parkway
Posts: 674
Default Re: Cotter pins

A common question is whether stainless steel is stronger that a grade 5 or grade 8 bolt. Stainless commonly comes in grades 18.8 (304) or T316. Stainless steel bolts are rated for corrosion resistance. Bolt strength is rated in PSI (pounds per square inch). A stainless steel bolt has the same PSI rating as a grade 5 bolt (125,000 PSI). A grade 8 bolt has a stronger rating with a PSI of 150,000.


From the above I would say that a SS Cotter Pin is stronger, I personally stay away from the china bolts and cotter pins



the above comes from:

https://www.nutsandbolts.com/v10-sta...eel-grade.html
holdover is offline   Reply With Quote
Old 11-01-2019, 01:32 PM   #12
Tom Endy
Senior Member
 
Tom Endy's Avatar
 
Join Date: May 2010
Location: Southern California
Posts: 3,122
Default Re: Cotter pins

This is what can happen in a Model A differential if you neglect to install a cotter pin on the end of the drive shaft. The nut came loose and backed off until it hit the rotating carrier. The carrier cut the nut in half (see the two pieces in one of the photos) the nut pieces got between the ring and pinion and did a number on the pinion gear.

Tom Endy
Attached Images
File Type: jpg nut diff.jpg (76.5 KB, 107 views)
File Type: jpg nut diff-2.jpg (52.7 KB, 108 views)
Tom Endy is offline   Reply With Quote
Old 11-01-2019, 02:43 PM   #13
jhowes
Senior Member
 
Join Date: Jul 2010
Location: upstate NY near Mass border
Posts: 789
Default Re: Cotter pins

Thanks Holdover, just what I wanted to know. Jack
jhowes is offline   Reply With Quote
Old 11-01-2019, 04:25 PM   #14
Joe K
Senior Member
 
Joe K's Avatar
 
Join Date: Jul 2010
Location: Cow Hampshire
Posts: 4,175
Default Re: Cotter pins

How about hammer lock cotter-pins? I don't think they were available - at least in the US.

https://en.wikipedia.org/wiki/Split_pin

Joe K
__________________
Shudda kept the horse.
Joe K is offline   Reply With Quote
Old 11-01-2019, 06:14 PM   #15
updraught
Senior Member
 
updraught's Avatar
 
Join Date: Feb 2015
Location: Australia
Posts: 1,967
Default Re: Cotter pins

So what colour were the cotter pins again?
updraught is offline   Reply With Quote
Old 11-02-2019, 08:02 AM   #16
Bob Bidonde
Senior Member
 
Bob Bidonde's Avatar
 
Join Date: May 2010
Location: Long Island, NY
Posts: 3,432
Default Re: Cotter pins

Hi Tom,
I had that exact pinion gear failure back in 1964, and it disabled my Coupe for a few years until I could afford to fix it. The pinion in my Coupe broke loose while I was driving at speed on a highway. What a mess it made.
Re stainless steel, it will cause galvanic corrosion of most carbon steels it comes in contact with. So it isn't good to mix stainless with other grades of steel.

As for the various types of stainless / corrosion resistant steels, this site defines the various alloys:
https://continentalsteel.com/stainless-steel/grades/
__________________
Bob Bidonde
Bob Bidonde is offline   Reply With Quote
Old 11-02-2019, 08:25 AM   #17
History
Senior Member
 
History's Avatar
 
Join Date: Oct 2017
Location: NC Mountains
Posts: 689
Default Re: Cotter pins

Seems the older cotter pins were thicker and softer compared to the box I have, even the replacement cotter pins I got from Snyders. Softer let's you form it more to the nut I'd imagine where it can't start loosening at all?
History is offline   Reply With Quote
Old 11-02-2019, 02:14 PM   #18
Will N
Senior Member
 
Will N's Avatar
 
Join Date: Jul 2010
Location: Pennsylvania
Posts: 1,096
Default Re: Cotter pins

Interesting to note too is that the form of today's cotter pins are not the same as those available during the Model A era. Modern cotter pin heads are kind of diamond shaped, while those made back in the day had rounded heads. You can't get those round head cotter pins today, so if you have an old jar of themlaying around I bet a fine point car restorer would pay good money for them.
Will N is offline   Reply With Quote
Old 11-02-2019, 02:48 PM   #19
CarlG
Senior Member
 
CarlG's Avatar
 
Join Date: Nov 2010
Location: Anchorage, Alaska
Posts: 9,109
Default Re: Cotter pins

Quote:
Originally Posted by Will N View Post
Interesting to note too is that the form of today's cotter pins are not the same as those available during the Model A era. Modern cotter pin heads are kind of diamond shaped, while those made back in the day had rounded heads. You can't get those round head cotter pins today, so if you have an old jar of them laying around I bet a fine point car restorer would pay good money for them.
But, you can get round head cotter pins. Here's a picture of what I have:
Attached Images
File Type: jpg Cotter Pins 1.jpg (39.6 KB, 54 views)
File Type: jpg Cotter Pins 2.jpg (85.4 KB, 100 views)
File Type: jpg Cotter Pins 3.jpg (59.3 KB, 68 views)
__________________
Alaskan A's
Antique Auto Mushers of Alaska
Model A Ford Club of America
Model A Restorers Club
Antique Automobile Club of America
Mullins Owner's Club
CarlG is offline   Reply With Quote
Old 11-02-2019, 04:46 PM   #20
henry's 31
Senior Member
 
Join Date: Mar 2014
Location: Columbus(Cataula) Georgia
Posts: 848
Default Re: Cotter pins

As it relates to cotter pins I agree with Alexiskai. The cotterpin just prevents the castle nut from backing up, so the material technically does not matter. One material may be easier to bend than another. When it comes to bolts, then the material matters.
__________________
Henry' s 31
henry's 31 is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 06:37 AM.