Go Back   The Ford Barn > General Discussion > Model A (1928-31)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 07-19-2020, 06:21 PM   #1
ericr
Senior Member
 
ericr's Avatar
 
Join Date: Apr 2012
Posts: 1,542
Default Anyone Ever Built or Even Seen, An Original type Greasing Pit?

-I know it would be a lot of work, but a lot of you guys apparently reside with some acreage and have built large garages etc. Plus a lot of us are nostalgic, eccentric, etc.

I suspect there are modern regulations on drainage and lighting within such a cavity.

I did see one in an old parking garage years ago, before it was torn down. As I recall it had narrow, steep steps on the end for access to the pit.
ericr is offline   Reply With Quote
Old 07-19-2020, 06:37 PM   #2
Jack Shaft
BANNED
 
Join Date: Dec 2019
Posts: 1,196
Default Re: Anyone Ever Built or Even Seen, An Original type Greasing Pit?

Pits are great till you fall in one...changes your whole outlook about them..I fell into the stair end,my fault,didnt chock the car.
Jack Shaft is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 07-19-2020, 06:58 PM   #3
Tacoma Bob
Senior Member
 
Tacoma Bob's Avatar
 
Join Date: May 2010
Location: Tacoma, WA
Posts: 1,025
Default Re: Anyone Ever Built or Even Seen, An Original type Greasing Pit?

Can only speak for Washington State but I was always told that pits were outlawed. for years here in town most had been covered up with heavy planking.
Tacoma Bob is offline   Reply With Quote
Old 07-19-2020, 07:06 PM   #4
The Master Cylinder
Senior Member
 
The Master Cylinder's Avatar
 
Join Date: Aug 2012
Posts: 875
Default Re: Anyone Ever Built or Even Seen, An Original type Greasing Pit?

Quote:
Originally Posted by Tacoma Bob View Post
Can only speak for Washington State but I was always told that pits were outlawed. for years here in town most had been covered up with heavy planking.
Yes, outlawed. That's why you don't see them in muffler shops anymore. Heavier than air gases tend to collect in them... Acetylene, propane, carbon dioxide, etc. Not a good thing.
__________________
The Master Cylinder

Enjoying life at the beach in SoCal...
The Master Cylinder is offline   Reply With Quote
Old 07-19-2020, 07:53 PM   #5
ursus
Senior Member
 
Join Date: May 2010
Location: Oregon
Posts: 1,369
Default Re: Anyone Ever Built or Even Seen, An Original type Greasing Pit?

Back in the '70's I had a car with a U-joint that was getting noisy and threatening to give out. A neighbor had a pit that he had installed 20 years earlier when he extended his garage. It sure made the job of replacing the U-joint easier. The pit installation had been approved by the city at the time.
ursus is offline   Reply With Quote
Old 07-19-2020, 08:03 PM   #6
wmws
BANNED
 
Join Date: Feb 2013
Location: Coatesville, Pa
Posts: 719
Default Re: Anyone Ever Built or Even Seen, An Original type Greasing Pit?

Sponsored Links (Register now to hide all advertisements)
I have a pit in my garage. I wouldn't be without it. I generally have my A parked over it. I can also put planks over it and they are the same hight as the garage floor. They are also heavy enough to drive over. Sure make working under the car easier.
wmws is offline   Reply With Quote
Old 07-19-2020, 08:26 PM   #7
McMimmcs
Senior Member
 
McMimmcs's Avatar
 
Join Date: Sep 2019
Location: Fort Gratiot, Michigan
Posts: 2,296
Default Re: Anyone Ever Built or Even Seen, An Original type Greasing Pit?

In my opinion not very practical ! Basically for lube jobs, mufflers and oil changes. Significant safety concerns concerning slips, falls on greasy steps, water and exhaust fumes. Maybe that's why you don't see them anymore . I had one and paid for the dirt to fill it in ! .
McMimmcs is offline   Reply With Quote
Old 07-19-2020, 08:46 PM   #8
holdover
Senior Member
 
Join Date: May 2011
Location: SW Virginia near the Blue ridge Parkway
Posts: 674
Default Re: Anyone Ever Built or Even Seen, An Original type Greasing Pit?

I have used them in the past, good for some jobs, not so for others. When lifts became available for a reasonable price, with rare exception, that was the end of pits. Had a local repair shop where I live that had a sign , "Use our pit to change your oil" not sure how many people did. As for me I have 2 four post lifts in my garage and being old and not so limber, they work good.
holdover is offline   Reply With Quote
Old 07-19-2020, 10:44 PM   #9
PalAl
Senior Member
 
PalAl's Avatar
 
Join Date: Jul 2016
Location: Orangeville Illinois
Posts: 461
Default Re: Anyone Ever Built or Even Seen, An Original type Greasing Pit?

Quote:
Originally Posted by holdover View Post
I have used them in the past, good for some jobs, not so for others. When lifts became available for a reasonable price, with rare exception, that was the end of pits. Had a local repair shop where I live that had a sign , "Use our pit to change your oil" not sure how many people did. As for me I have 2 four post lifts in my garage and being old and not so limber, they work good.
What brand hoists did you go with? What weight load? Thanks
PalAl is offline   Reply With Quote
Old 07-19-2020, 10:52 PM   #10
Bill G
Senior Member
 
Bill G's Avatar
 
Join Date: Jun 2017
Location: Walla Walla, WA
Posts: 1,044
Default Re: Anyone Ever Built or Even Seen, An Original type Greasing Pit?

I know a man who was once injured when he lost his footing on an oily stair step and fell into a pit and screed up both his knees. I can see why they are outlawed. He no longer works in the automotive industry, other than he has a restoration project going on.
Bill G is offline   Reply With Quote
Old 07-20-2020, 12:17 AM   #11
J Franklin
Senior Member
 
J Franklin's Avatar
 
Join Date: May 2010
Location: Oregon
Posts: 5,946
Default Re: Anyone Ever Built or Even Seen, An Original type Greasing Pit?

Thy are used in quick Lub shops in Oregon.
J Franklin is offline   Reply With Quote
Old 07-20-2020, 04:52 AM   #12
Bruce of MN
Senior Member
 
Bruce of MN's Avatar
 
Join Date: May 2010
Location: VA
Posts: 1,394
Default Re: Anyone Ever Built or Even Seen, An Original type Greasing Pit?

Quote:
Originally Posted by J Franklin View Post
Thy are used in quick Lub shops in Oregon.
I've seen them in other states, too. Somehow in my career, I was aware of code requirements for vent fans to draw away gas vapors in the pit, sort of like bilge ventilation.

I have a vague memory of my Dad taking me with him in my coupe in '53 or so to a repair shop with a pit in Colorado Springs. Seems like it was pretty rudimentary.
Bruce of MN is offline   Reply With Quote
Old 07-20-2020, 05:17 AM   #13
Patrick L.
Senior Member
 
Patrick L.'s Avatar
 
Join Date: May 2010
Location: Largo Florida
Posts: 7,225
Default Re: Anyone Ever Built or Even Seen, An Original type Greasing Pit?

We had 3. They are nice, but,,,

In a busy garage things tend to get messy. While doing some exhaust work it caught fire. Of course the transmitter was in park and the rear bumper was over the stairs. I had a heck of a time getting the trans lever to move so I could push the car back so I could get out. The fire was also at the back blocking me and under the fuel tank. Never put a car in park on one after that.
That was back when we had 4 twin post Weavers and a drive on lube rack [ can't recall the make]
Patrick L. is offline   Reply With Quote
Old 07-20-2020, 07:46 AM   #14
aermotor
Senior Member
 
Join Date: Mar 2015
Location: Greenville, SC
Posts: 1,099
Default Re: Anyone Ever Built or Even Seen, An Original type Greasing Pit?

Not to long in the past I remember using ditches as grease pits - back then pollution was not as much concern as today. Just moved the car uphill a notch to keep from laying in the used oil. BTW, still have a Valvoline quick lube 2 blocks from my home in SC with a pit I use due to older age.

John

Last edited by aermotor; 07-20-2020 at 07:52 AM.
aermotor is offline   Reply With Quote
Old 07-20-2020, 08:19 AM   #15
Lona
Senior Member
 
Lona's Avatar
 
Join Date: Dec 2013
Location: Gloucester, Va
Posts: 464
Default Re: Anyone Ever Built or Even Seen, An Original type Greasing Pit?

A fellow Peace Corps volunteer and I broke through a concrete floor and dug our own pit by hand while we were setting up a school for young mechanics in Chile in 1961. Used cement on the walls and floor and welded up a ladder for one end. Even built cement curbs along each side to prevent car wheels from falling in. You could probably buy two regular lifts for what it would cost to dig and finish a pit today.

Quick lube centers in Virginia still use them, probably to save time raising and lowering cars on a lift but I understand they are well regulated with regard to ventilation, carbon monoxide alarms and such. A few years ago, I almost bought a house with a detached garage that had a pit. Wonder what my insurance agent would have thought about that.

Glen
__________________
'31 Model A Deluxe Roadster
'31 Chrysler Model 70 Sedan
'88 Pontiac Fiero GT
'36 Auburn Boattail Speedster replica
Lona is offline   Reply With Quote
Old 07-20-2020, 09:11 AM   #16
77Birdman
Senior Member
 
Join Date: Nov 2018
Location: North Eastern MD
Posts: 486
Default Re: Anyone Ever Built or Even Seen, An Original type Greasing Pit?

There was an old timer that had one in his welding shop. Only one I ever saw working. I always thought they were dangerous for a lot of the above reasons.
I was stopped in my truck by the state DOT at a weigh station in MD and they have one that is pretty new and in use. It makes inspecting the drivetrain of trucks very easy I suppose.
As a contractor, for the cost of putting one in the right way, a lift would probably end up being about half the price.
77Birdman is offline   Reply With Quote
Old 07-20-2020, 10:43 AM   #17
BRENT in 10-uh-C
Senior Member
 
BRENT in 10-uh-C's Avatar
 
Join Date: May 2010
Location: Eastern Tennessee
Posts: 11,484
Default Re: Anyone Ever Built or Even Seen, An Original type Greasing Pit?

All of the above are very valid reasons, ...however all of the ones I ever worked in were filthy and an absolute mess. Likely because they were hard to clean, and to wash out. Even front end alignment pits that I worked in became dark dungeons over time. I personally don't think I would like to work in another pit. Add me to that list of 'Lifts have spoiled me too!'.
__________________
.

BRENT in 10-uh-C
.
www.model-a-ford.com
...(...Finally Updated!! )

.
BRENT in 10-uh-C is offline   Reply With Quote
Old 07-20-2020, 11:21 AM   #18
fastroadster
Senior Member
 
Join Date: Oct 2014
Location: Santa Cruz Ca.
Posts: 175
Default Re: Anyone Ever Built or Even Seen, An Original type Greasing Pit?

Still have and still use..... my pit. Put in 1958
fastroadster is offline   Reply With Quote
Old 07-20-2020, 01:40 PM   #19
Big hammer
Senior Member
 
Join Date: Jun 2014
Location: Land of Lincoln
Posts: 3,114
Default Re: Anyone Ever Built or Even Seen, An Original type Greasing Pit?

I ate in a greasy pit once...........................we call them greasy spoon restaurants! ��
__________________
Don't force it with a little hammer tap, tap, tap
get a bigger hammer tap done
Big hammer is offline   Reply With Quote
Old 07-20-2020, 01:44 PM   #20
burner31
Senior Member
 
burner31's Avatar
 
Join Date: Dec 2014
Location: Shawnee, Ok
Posts: 3,471
Default Re: Anyone Ever Built or Even Seen, An Original type Greasing Pit?

Used to play in them all the time as kid, but that was back in the 50s, then the cuban missile crisis hit and some of those pits were expanded and turned into bomb shelters, and those were really fun to play in.
__________________
Keith
Shawnee OK
'31 SW 160-B
burner31 is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 06:41 AM.