|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
01-27-2012, 06:29 AM | #21 |
Senior Member
Join Date: May 2010
Location: Asheville,NC
Posts: 3,104
|
Re: Snyder's: New insert connecting rods
Marco, on the cranks you measured, did you use the crank specifically ground for inserts? This would make a difference because that crank is ground only for inserts and is .001 smaller than the factory standard one Chris sells which is used for babbitt. Mike is correct with his comment if using the insert crank with inserts as opposed to the babbitt crank with babbitt. The confusion came when he put the word STD. in his post. He is alluding to STD for size with inserts not babbitt.
Last edited by James Rogers; 01-27-2012 at 06:35 AM. |
01-27-2012, 07:00 AM | #22 |
Senior Member
Join Date: May 2010
Location: lafayette,la
Posts: 459
|
Re: Snyder's: New insert connecting rods
RUSTY. you don't need pressure to run inserted engine. Regular A oil system is fine.
|
Sponsored Links (Register now to hide all advertisements) |
|
01-27-2012, 09:38 AM | #23 |
Senior Member
Join Date: May 2010
Location: Torrington, CT
Posts: 609
|
Re: Snyder's: New insert connecting rods
Where are they made?
My vote is for the one made in the USA |
01-27-2012, 09:44 AM | #24 | |
Senior Member
Join Date: May 2010
Location: Jordan, MN
Posts: 1,411
|
Re: Snyder's: New insert connecting rods
Quote:
But I am willing to be the guinea pig! I am moving to phase two of a test engine I built last year and I have the opportunity to test the rods in an engine I have control over. In my test engine, I am upgrading to a Burlington crankshaft from a counterweighted standard crank. I will be adding additional carburetion and a high flow Aries muffler. I will install the Snyder rods in this test engine and place it in my driver to run this summer. I should accumulate over 5000 miles with the trips we have planned. I will then remove the engine and disassemble it to verify clearances and surfaces. I already know AER makes an excellent rod and insert bearing. If the oil clearance between the journal and the insert is held close to .00175", there are no problems. I have used about 60 sets over the past 4 years and have complete faith in the AER rod. I know this discussion is about quality but value also enters into the equation for me. The cost of the Snyder rod set is about $170.00 less than the AER rod set. If they provide good/equal service and cost less, my customers may prefer to save the $170.00 in the cost of their engine build. I need to be ready to use the Snyder rod set if a customer requests it. I don’t want to test these rods in a customer’s engine but I will in my own. Trying them is the only way I will know if they are as good as the Snyder Press Release claims. Good Day! Dave in MN www.durableperformance.net Last edited by Dave in MN; 01-27-2012 at 10:04 AM. |
|
01-27-2012, 10:26 AM | #25 |
Senior Member
Join Date: May 2010
Location: Connecticut
Posts: 272
|
Re: Snyder's: New insert connecting rods
Hi Guys, Just a quick note on the Burlington Crankshaft. The rod pins are 0.002 smaller than the fractional one-and-a-half inches. The mains are 0.002 smaller than the fractional one-and-five-eighths inches. This conforms to the original factory prints for the Ford A crankshaft. Yes, the crank was intended for an original babbitt-type installation in the A block.
Sometime ago, Rich Falluca at AER manufactured some .002 (yes, with clearances!) oversized inserts specifically to be used with insert installations of the BC. These inserts have turned out to work very well with BC equipped engines! Please note that you will detect some variations in the "tens" column on these measurements, but all will be within original factory specs as described in the original prints. Thanks for your continuing attention and comments! Chris ----------------------------------------------- www.burlingtoncrankshaft.com |
01-27-2012, 10:49 AM | #26 |
Senior Member
Join Date: May 2010
Location: Wilmington, Delaware
Posts: 240
|
Re: Snyder's: New insert connecting rods
Sponsored Links (Register now to hide all advertisements)
I took a chance based on Ora's knowledge and trouble-free experience with them and got the all-new AER rods with inserts. Couple thousand miles on them so far with zero problems. We'll see in the long-haul. I asked Ora about the the need to now pressurize my system and he said not necessary for rods only ("Unless I planned to use the engine exceptionally hard as in racing, hill-climbing, etc."). If I had the mains inserted then pressurization would be highly recommended. His typical rods-only insert customers do not go to pressurization and do very well with very long life on the rod inserts. And they are comparatively "easy" to replace if you're lucky enough to catch them before they sieze and spin upon failure. This was my biggest fear (besides the cost!) about the inserts. They don't give you a "pre-siezure/spin" audible warning like my failed rod babbits did. Then you'll need a re-worked/replaced crank. Ya don't get somethin' for nothin'. Any thoughts here about the pressurization question? - with detailed rationale? Thanks Earle |
01-27-2012, 11:55 AM | #27 | |
Senior Member
Join Date: May 2010
Posts: 3,099
|
Re: Snyder's: New insert connecting rods
Quote:
"If you are running one of the new A-6303 Burlington counterbalanced crankshafts, you will need to use these A-6331-002 bearings." Part Number - A-6331-002 Specifics - .002 under sized - 1928-31 Price - $90.00 / set So it's becoming quite apparent that folks don't understand that the early Fords had the bearings done at the nominal size. The "clearance" was provided by the journal dimension. SO if the inserts were made for a Model A how can they call them undersized? If they made them any larger you would have to build up the journals on a NOS crankshaft!!!
__________________
http://www.abarnyard.com/ |
|
01-27-2012, 01:01 PM | #28 |
Senior Member
Join Date: May 2010
Location: Santa Rosa, CA
Posts: 1,279
|
Re: Snyder's: New insert connecting rods
Regarding the pressurization question raised by Earle, the circumferential groove and partial parting line relief on the inserts shown here is substantially different than the stock, unpressurized, rod bearings.
The stock rods had X grooves across the rod and cap, with a V groove across the entire rod at the parting line relief and continuing across the thrust face. These carry oil across the entire bearing. There is also a "faired out" scoop at the oil inlet dipper hole that directs oil to the center of the bearing rather than around the entire bearing which the single circumferential groove does. The stock grooves will spread the oil across the entire bearing and allows seepage across the thrust face. As a general proposition, the circumferential groove is for use in pressurized systems because unpressurized oil will only seep about 1/2 inch from the groove, about one inch total, less than the 1 5/8 inch width of the A rod journal. This may help explain the uneven wear and ring that Eystein experienced. The parting line relief in the inserts shown here may alleviate that problem, and perhaps Eystein could tell us if his inserts had that parting line relief. If not, it is likely that there was inadequate lubrication on the sides of the journal removed from the circumferential groove. Another question I have about the single circumferential groove is that the pressure generated when the dipper hits the oil in the tray (about 20-30 lbs at speed) is immediately lost by escape through the holes in the rod big end that spurts oil upward into the cylinder area, and is asserted by Murray Fahnestock to collect additional oil from the mist on the upward stroke. Fahnestock was close to Ford, and his thoughts may reflect the thinking of the Ford engineers. The modern circumferential insert groove does not have this "pressure release" hole while the Model A insert does. Nor would I use a MOdel A rod without a side thrust flange, with all due respect to Mike K. Removal of that flange will add about .100 to the rod end play, rather than the .008-.012 called for in the specs. With .040-.050 end play on the pin, that rod will migrate back and forth across that distance during operation. I doubt that modern rods have that kind of end play, with or without an insert flange. I personally do not use circumferential grooves on my unpressurized system. It would seem to me that the manufacturers could make inserts, rods and mains, that mimic the Ford grooves which have an 80 year history. Babbitt failure is much more likely the result of improper babbitt installation than inadequate lubrication if the stock design is followed. (Ask Herm his opinion about babbitt installation!) Unfortunately, most babbitt bearings I have seen do not use the Ford groove design. One of the arguments in favor of inserts is that the quality of material is fairly uniform and good, while the quality of babbitt material and installation is uneven at best. I look forward to seeing the results of Dave in Mn's tests and appreciate his willingness to be a "guinea pig." The Model A is simple and durable enough that about anything will (and has) work for awhile. But as noted, I would feel much more comfortable using unpressurized inserts if they had the Ford groove design. Inserts are probably the wave of the future because quality babbitt installation is getting harder to find and the guys that do it are usually some long distance away. If that is the case, I would like to see the insert manufacturers get the best design. I personally do not think that a modern groove system premised on pressure oil is applicable to an unpressurized system, but I am more than willing to see what the results prove. Unfortunately, it is going to take some time to get reliable results. My opinion notwithstanding, this is a good discussion of an important issue that is short on facts and long on opinion. I have tried to upload some pics but that has not worked. Will try again later, or maybe find a 10 year old to show me how to do it. Or perhaps someone with more computer knowledge than I can help us out here. My article in the January 2010 Restorer has pics and more detail. Last edited by PC/SR; 01-27-2012 at 02:48 PM. |
01-27-2012, 02:34 PM | #29 | |
Senior Member
Join Date: May 2010
Location: Windy City
Posts: 2,919
|
Re: Snyder's: New insert connecting rods
Quote:
|
|
01-27-2012, 02:39 PM | #30 | |
Senior Member
Join Date: May 2010
Location: 60615,330th Ave.,Clare, Iowa, 50524
Posts: 1,457
|
Re: Snyder's: New insert connecting rods
Quote:
Normally, the reason that some rebabbitted rods come with a circle grooving, is the rebabbitter does not have the machine to x groove with, and as you say Mr. P.C., they just don't spread the oil, in a splash system. Herm. |
|
01-27-2012, 03:03 PM | #31 | |
Senior Member
Join Date: May 2010
Location: NC
Posts: 2,975
|
Re: Snyder's: New insert connecting rods
Quote:
My experience with pressure to the rods is when you drill the crank you weaken it to much and it will break. Maybe not if you drive like you should. I have been known to hill climb. |
|
01-27-2012, 03:05 PM | #32 |
Senior Member
Join Date: May 2010
Location: NC
Posts: 2,975
|
Re: Snyder's: New insert connecting rods
|
01-27-2012, 03:28 PM | #33 |
Senior Member
Join Date: May 2010
Location: Fresno, Ca.
Posts: 3,636
|
Re: Snyder's: New insert connecting rods
George,
" My experience with pressure to the rods is when you drill the crank you weaken it to much and it will break. Maybe not if you drive like you should. " I agree, since we are dealing with cranks that have no journal overlap, and no easy way to fix the problem. However, I'm planning on a drilled crank with splash system to insure a constant flow of oil to the rods......a poor man's " sludge pocket " crank. Dudley |
01-27-2012, 04:25 PM | #34 | |
Senior Member
Join Date: May 2010
Location: Jordan, MN
Posts: 1,411
|
Re: Snyder's: New insert connecting rods
Quote:
Thanks for your input guys! Dave in MN Last edited by Dave in MN; 01-27-2012 at 04:31 PM. |
|
01-27-2012, 07:25 PM | #35 |
Senior Member
Join Date: May 2010
Location: Asheville,NC
Posts: 3,104
|
Re: Snyder's: New insert connecting rods
George, I spoke to Rich about why the inserts were different. According to him the shells were available but needed some mods to work. The size was not adjustable so the finished product was a bit off size. It is easier to make sure the grind is right than to modify the shells.
|
01-27-2012, 07:44 PM | #36 |
Senior Member
Join Date: May 2010
Location: Santa Rosa, CA
Posts: 1,279
|
Re: Snyder's: New insert connecting rods
Dave: I am glad your inserts worked out for you. And yes your experience and that of all who use inserts has to be considered. The trick is to find out what and why it worked well for you and not so well for Eystein so that your experience and be repeated and shared and Eystein's avoided.
I assume the insert shells you used were for a modern production engine. As such, they would likely be thinner at the parting line than at the center, and would therefore create as sort of oil resevoir all the way across the parting line similar to the original model A design. I do not know if the AER inserts are thinner at the parting line, or if there is a V type relief there. There should be something there to create the oil resevoir and avoid the wiping action of a sharp edge. The Snyder inserts shown in this thread have a parting line relief that is wide and closed at the ends, similar to the original reliefs on the A main bearings. If I were to use these inserts, I would file a small V across the remainder of the parting line and across the thrust flange to imitate the original A design. I have nothing against inserts per se, and do not doubt that perfectly fine inserts can be designed for the Model A. However, part of the problem as I see it is that new and old technologies are being merged on a more or less trial and error basis. Nothing wrong with that and I admire the initiative of the guys that are doing it. I do not intend my comments to be construed as negative, but as something to be considered by the innovators and hopefully the final result will be something useful to all of us. At this point, I think inserts grooved to the model A design would work best. Last edited by PC/SR; 01-27-2012 at 08:07 PM. |
01-27-2012, 08:18 PM | #37 |
Senior Member
Join Date: May 2010
Location: 60615,330th Ave.,Clare, Iowa, 50524
Posts: 1,457
|
Re: Snyder's: New insert connecting rods
Dave, With a babbitt rod, or a insert rod, we set oil clearance, to .001 thousandths per inch. It wouldn't be wise the set the clearance closer on a babbitt bearing, as you will smear it. Your clearance on your insert rod, of 1 and 3/4 thousandths is in the middle of what it should be, Minimum should be .00160, to Max at .00210.
Dave, with 52,000 on, have you ever checked the running clearance on them? Question, if you would get a .001, or .00150 wear on the shaft, with out shims what would be your adjustment plan of attack, are smaller sizes available, or will they be at the time you need them? There are inserts added every day to the obsolete list. Also one of the draw backs of a circle groove, where the groove does not wear on the shaft, and the rest of the shaft does wear, you have that raised area on the crank, and have to insure the new inserts bottom on the shaft. If it sounds like I am against inserts, not true, I am for anything that works well. Thanks Herm. |
01-28-2012, 10:34 AM | #38 | |
Senior Member
Join Date: May 2010
Location: Connecticut
Posts: 272
|
Re: Snyder's: New insert connecting rods
Quote:
Chris |
|
01-28-2012, 03:23 PM | #39 |
Junior Member
Join Date: May 2010
Posts: 19
|
Re: Snyder's: New insert connecting rods
The Ford crankshaft drawing that Marco posted would be a nice thing to have in one's files. Is there any way that you could make it available to us in a size that we could read the dimensions on?
|
01-28-2012, 03:31 PM | #40 |
Senior Member
Join Date: Aug 2010
Posts: 260
|
Re: Snyder's: New insert connecting rods
I would like to start work on my 29 AA engine soon. I'm a self employed machinist with a mill and lathe. If I take a stock model A rod and a new Snyders flange type insert bearing, can I make them work? I can make a fixture that will hold the rod perpendicular to the spindle and bore it out, measure it with a starret inside mice. Would anyone know the bore size?
For years I'v heard of using 283 gm pistons on A rods. I have a Seal Power catalog, engine parts specifications. The compression distance of the A piston is 1.906", I measure one and that is correct. The cd on the 283 is 1.780" depending on which one is used. The difference is .126", that would be too much of loss in compression. Please give me some more info on this subject. Thanks, carry on, nick c |
|
|
Sponsored Links (Register now to hide all advertisements) |
|