|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
|
12-10-2014, 07:43 PM | #1 |
Senior Member
Join Date: May 2010
Location: Rogersville, TN
Posts: 797
|
39 clutch pedal lock pin
Anything special about the pins that lock the pedal to the shaft when replacing?
CRS ok? |
12-11-2014, 09:27 AM | #2 |
Senior Member
Join Date: May 2010
Location: Florida and Penna.
Posts: 4,471
|
Re: 39 clutch pedal lock pin
I would use a hardened roll pin. G.M.
__________________
www.fordcollector.com |
Sponsored Links (Register now to hide all advertisements) |
|
12-11-2014, 09:30 AM | #3 |
Senior Member
Join Date: Jun 2010
Location: Perry OH
Posts: 1,329
|
Re: 39 clutch pedal lock pin
Ditto G.M. hardened roll pin.
|
12-11-2014, 09:34 AM | #4 |
Senior Member
Join Date: May 2010
Location: Delta, PA
Posts: 525
|
Re: 39 clutch pedal lock pin
I used a grade 8 bolt, long and cut to fit with smooth shoulder in arm and shaft. Zeke
__________________
Only problem with retirement is never a day off Last edited by Zeke...PA; 12-12-2014 at 08:45 AM. |
12-11-2014, 11:26 AM | #5 |
Senior Member
Join Date: Feb 2011
Location: Buchanan, MI
Posts: 676
|
Re: 39 clutch pedal lock pin
There is nothing hard about the original equipment pin, either on the throwout fork or the clutch arm.
That is how we are able to drill them when removing. All aftermarket pins are mild steel. |
12-11-2014, 01:20 PM | #6 |
Senior Member
Join Date: May 2010
Location: East Shore of LAKE HOUSTON
Posts: 11,106
|
Re: 39 clutch pedal lock pin
Sponsored Links (Register now to hide all advertisements)
|
12-11-2014, 01:36 PM | #7 |
Senior Member
Join Date: May 2010
Location: Rogersville, TN
Posts: 797
|
Re: 39 clutch pedal lock pin
Thanks!
It look like it needs to be installed like a rivet, as it is peened over hot, the pin expands in the hole and locks pedal and shaft together. IMHO. |
12-11-2014, 01:43 PM | #8 |
Senior Member
Join Date: May 2010
Location: East Shore of LAKE HOUSTON
Posts: 11,106
|
Re: 39 clutch pedal lock pin
Actually, most guys use a QUALITY bolt that fits snugly. You probably won't put enough miles on it to wear it out. DD
|
12-11-2014, 01:55 PM | #9 |
Senior Member
Join Date: Jun 2014
Location: Salt Lake City, Utah
Posts: 756
|
Re: 39 clutch pedal lock pin
I just bought a allen 5/16 head shoulder bolt. It has a long shank for strength and a tight fit. Ream the hole to dia so it doesn't fret in the hole and wear the pedal or shaft assembly.
Roll pins are both thin and hollow and are not meant to carry a shear load. |
12-11-2014, 01:57 PM | #10 |
Senior Member
Join Date: Jun 2014
Location: Salt Lake City, Utah
Posts: 756
|
Re: 39 clutch pedal lock pin
Let me clarify that the "load" is the issue not the shearing force.
|
12-11-2014, 01:59 PM | #11 |
Senior Member
Join Date: May 2010
Location: East Shore of LAKE HOUSTON
Posts: 11,106
|
Re: 39 clutch pedal lock pin
I'll "second" that warning about not using a roll pin...NOT for THAT MUCH shear load! DD
|
12-11-2014, 06:18 PM | #12 |
Senior Member
Join Date: May 2010
Location: Minnesota
Posts: 1,825
|
Re: 39 clutch pedal lock pin
The OP is asking about the pin that holds the pedal arm to the cross shaft, not the clevis and pin in the linkage.
Hard to get a bolt to fit tight enough, easier to heat and upset the ends like a rivet, seems to expand and fit the hole good and tight. Don't think a roll pin would have a long life in this application, bet it would get loose pretty quick. |
12-11-2014, 07:08 PM | #13 |
Senior Member
Join Date: May 2010
Location: Garlic Country of CA
Posts: 537
|
Re: 39 clutch pedal lock pin
I would not ream the hole as is suggested, too much material is removed and a new pin will not peen in tight enough to take up the clearance. I use the new supplied pins from Job Lot or others and peen cold when installing the clutch throw out arm on the transmission throw out fork shaft (same type of installation as pedal shaft).
Thanks Paul J. |
12-11-2014, 07:52 PM | #14 |
Senior Member
Join Date: Jun 2014
Location: Salt Lake City, Utah
Posts: 756
|
Re: 39 clutch pedal lock pin
Please take a look, the shoulder extends thru the pedal arm. Hole is.309 and pin is .308 dia. The standard grade 5 bolt threads are too long (my taste) for the shoulder length. A shorter bolt has insufficient shoulder. A solid pin is great but I want to be able to disassemble. In any case this is not about convincing you what to do as providing options.
|
12-11-2014, 08:38 PM | #15 |
Senior Member
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,990
|
Re: 39 clutch pedal lock pin
'42merc" and "V8coopman" have offered some very good advice. The pin was originally mild steel and swedged in place.
If you want to maintain the authentic appearance, simply install a piece of cold rolled steel and peen over each end. You'll never sheer this pin...
__________________
"I can explain it for you. However, I can't understand it for you". |
12-12-2014, 02:33 AM | #16 |
Senior Member
Join Date: May 2010
Location: Solihull, England.
Posts: 8,745
|
Re: 39 clutch pedal lock pin
If you decide to use a bolt, use one with the desired length of plain shaft and then saw the threaded part down to length. How hard can it be? The 39 pedals in my 33 already had a bolt in place so i just reworked the job with a new bolt modified as above.
Mart. |
|
|
Sponsored Links (Register now to hide all advertisements) |
|