Go Back   The Ford Barn > General Discussion > Early V8 (1932-53)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 03-06-2021, 08:43 AM   #1
Jakno
Senior Member
 
Jakno's Avatar
 
Join Date: Sep 2014
Location: Maine
Posts: 325
Default 59A low compression #4 cyl

Purchased a Project 33 PU several years ago complete with 59 engine. Have decided to get going on completing the truck. Started with checking the engine for issues. Compression check shows all cyl except # 4 to be 80 to 95 lbs. # 4 cyl is 34-40 lbs .All these cylinders are original parts except, #4 cyl intake and exhaust valves have been replaced. The low compression in #4 does not appear to be a valve problem although I am going to replace them with VanPelt valves.
The cylinder walls are what you would expect in this original engine and all 8 cylinders are consistent. I also have new head gaskets.

Would you share your thoughts on anything you might try before I have to tear down the engine. ..... Thanks
Attached Images
File Type: jpg 33 PU.jpg (126.4 KB, 39 views)
File Type: jpg 59A #4 cyl.jpg (116.6 KB, 68 views)
File Type: jpg 59A Right Side.jpg (115.0 KB, 62 views)
__________________
Lineman, the only dumb animal that can harness himself !!
Jakno is offline   Reply With Quote
Old 03-06-2021, 08:53 AM   #2
marko39
Senior Member
 
Join Date: Oct 2016
Location: harpursville ny
Posts: 1,038
Default Re: 59A low compression #4 cyl

You could replace the head and do a leak down test to find problem.
marko39 is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 03-06-2021, 09:10 AM   #3
Bored&Stroked
Senior Member
 
Bored&Stroked's Avatar
 
Join Date: Jan 2011
Location: Central Ohio
Posts: 5,013
Default Re: 59A low compression #4 cyl

Since you've come this far, why waste a set of head gaskets on it - when you really don't know the issue. If it was mine, I'd take it all the way down - being careful to label where all the parts go (pistons, bearings, etc) - and check it out in detail. Depending on what you find - maybe you get away with new rings a cylinder hone and a valve job. If you're trying to do it on the cheap, then you might get away with some basic/simple stuff - all depending on amount of wear and condition of everything.

Me - I'm never that lucky and I'm too particular anyway - I always end up with a full rebuild! LOL
Bored&Stroked is offline   Reply With Quote
Old 03-06-2021, 09:41 AM   #4
flatford8
Senior Member
 
flatford8's Avatar
 
Join Date: Jan 2012
Location: Lyman,ME.
Posts: 2,612
Default Re: 59A low compression #4 cyl

In pic #2, is that a burn mark at 11:00 on the exhaust valve?...... Mark
__________________
I'm thinkin' about crankin'
My ragged ol' truck up
and haulin' myself into town.
Billy Joe Shaver
flatford8 is offline   Reply With Quote
Old 03-06-2021, 09:42 AM   #5
Ken hash
Member
 
Ken hash's Avatar
 
Join Date: Dec 2020
Location: Ellensburg wa
Posts: 58
Default Re: 59A low compression #4 cyl

Don’t shoot me, but now is the time to tear this motor down and have it hot tanked and magnifluxed. You may have a crack in the valve chamber that you can’t see with the naked eye.most small cracks can be fixed. Good luck.
Ken hash is offline   Reply With Quote
Old 03-06-2021, 10:45 AM   #6
Jakno
Senior Member
 
Jakno's Avatar
 
Join Date: Sep 2014
Location: Maine
Posts: 325
Default Re: 59A low compression #4 cyl

Sponsored Links (Register now to hide all advertisements)
Thanks for your help and advice which is all good. I agree a full rebuild is what it will need eventually. My problem is I currently have one in the shop being rebuilt for my 35 PU and I'd like to use this engine shot term. FlatFord8, I'm quite certain that the mark at 11 o'clock is not a burn mark.
Question - If I had a stuck piston ring on cylinder 4, could that cause low compression and has anyone ever been able to free it with out pulling the piston. ?
__________________
Lineman, the only dumb animal that can harness himself !!
Jakno is offline   Reply With Quote
Old 03-06-2021, 11:07 AM   #7
tubman
Senior Member
 
tubman's Avatar
 
Join Date: Dec 2013
Location: Minnesota, Florida Keys
Posts: 10,260
Default Re: 59A low compression #4 cyl

I can completely understand the desire to not end up with two flatheads in the machine shop at the same time. I think for the time being, you should clean up the surfaces and re-install the head with a new gasket. Then, as "marko39" suggests, do a leak down test to find out where the problem is. Depending on what you find, I would button it back up and fire it up. You didn't say how long it had been sitting, but things can get gummed up over time. If the engine doesn't make any funny noises and has good oil pressure, using it may just loosen up anything that may be sticking. Proceed step by step, and there is a pretty good chance that you will end up with a good runner. (Don't forget the MMO and maybe some SeaFoam.)
tubman is offline   Reply With Quote
Old 03-06-2021, 11:17 AM   #8
Jakno
Senior Member
 
Jakno's Avatar
 
Join Date: Sep 2014
Location: Maine
Posts: 325
Default Re: 59A low compression #4 cyl

Mr. Tubman, thanks for your response and idea's. Your advice is what I'd hoping to try as a Hail Mary fix. The engine has been out of service for at least 10 years maybe longer.

Would you mind sharing on how to go about a "Leak Down test ". I'll try a Forum Search as well.
__________________
Lineman, the only dumb animal that can harness himself !!
Jakno is offline   Reply With Quote
Old 03-06-2021, 01:27 PM   #9
flatford8
Senior Member
 
flatford8's Avatar
 
Join Date: Jan 2012
Location: Lyman,ME.
Posts: 2,612
Default Re: 59A low compression #4 cyl

Google might be quicker. Spray some penetrant around that piston for a few days and maybe it’ll free the ring....... Mark
__________________
I'm thinkin' about crankin'
My ragged ol' truck up
and haulin' myself into town.
Billy Joe Shaver
flatford8 is offline   Reply With Quote
Old 03-06-2021, 01:31 PM   #10
flatford8
Senior Member
 
flatford8's Avatar
 
Join Date: Jan 2012
Location: Lyman,ME.
Posts: 2,612
Default Re: 59A low compression #4 cyl

https://www.mobil.com/en/lubricants/...-leakdown-test I found this in my stash of info...... Mark
__________________
I'm thinkin' about crankin'
My ragged ol' truck up
and haulin' myself into town.
Billy Joe Shaver
flatford8 is offline   Reply With Quote
Old 03-06-2021, 01:32 PM   #11
Ggmac
Senior Member
 
Join Date: Jul 2016
Location: Lake worth Florida
Posts: 1,073
Default Re: 59A low compression #4 cyl

Quote:
Originally Posted by Jakno View Post
Purchased a Project 33 PU several years ago complete with 59 engine. Have decided to get going on completing the truck. Started with checking the engine for issues. Compression check shows all cyl except # 4 to be 80 to 95 lbs. # 4 cyl is 34-40 lbs .All these cylinders are original parts except, #4 cyl intake and exhaust valves have been replaced. The low compression in #4 does not appear to be a valve problem although I am going to replace them with VanPelt valves.
The cylinder walls are what you would expect in this original engine and all 8 cylinders are consistent. I also have new head gaskets.

Would you share your thoughts on anything you might try before I have to tear down the engine. ..... Thanks
Can you take a pic without the gasket on ?
Ggmac is offline   Reply With Quote
Old 03-06-2021, 02:28 PM   #12
JSeery
Member Emeritus
 
JSeery's Avatar
 
Join Date: Nov 2012
Location: Wichita KS
Posts: 16,132
Default Re: 59A low compression #4 cyl

Question: Was the compression testing performed wet or dry (oil in the cylinder for wet)? A wet test should tell you if it is a ring issue.
JSeery is offline   Reply With Quote
Old 03-06-2021, 02:46 PM   #13
Jakno
Senior Member
 
Jakno's Avatar
 
Join Date: Sep 2014
Location: Maine
Posts: 325
Default Re: 59A low compression #4 cyl

Thanks for the help everyone. I have removed the head and going to put the penetrant in the cylinder for a couple of days. I'll give it a short turn now and then. Flatford 8 ,Thanks for info on the leak down test. I'll give that a try after the penetrant.
__________________
Lineman, the only dumb animal that can harness himself !!
Jakno is offline   Reply With Quote
Old 03-06-2021, 04:04 PM   #14
Art Newland
Senior Member
 
Art Newland's Avatar
 
Join Date: Mar 2016
Location: Lynden, WA
Posts: 1,564
Default Re: 59A low compression #4 cyl

A sticky valve (taking too long to close) could cause your problem too.
__________________
"whatever works!"
Art Newland is offline   Reply With Quote
Old 03-06-2021, 05:13 PM   #15
Jakno
Senior Member
 
Jakno's Avatar
 
Join Date: Sep 2014
Location: Maine
Posts: 325
Default Re: 59A low compression #4 cyl

Thanks Mr Newland. A sticky valve might explain why I get different readings each time I do a compression test Ex.. readings of 20 PSI, 35 and 40 PSI
__________________
Lineman, the only dumb animal that can harness himself !!
Jakno is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 06:01 AM.