Go Back   The Ford Barn > General Discussion > Model A (1928-31)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 12-04-2019, 01:30 PM   #1
GPierce
Senior Member
 
GPierce's Avatar
 
Join Date: Dec 2014
Location: Germantown,TN
Posts: 513
Default High compression head vs cooling

Does using a high compression head create more heat for the cooling system to remove?

I know the heat of compression will be higher.
GPierce is offline   Reply With Quote
Old 12-04-2019, 01:34 PM   #2
chrs1961815
Senior Member
 
chrs1961815's Avatar
 
Join Date: Jul 2018
Location: Spring Grove, Illinois
Posts: 1,371
Default Re: High compression head vs cooling

More heat in the engine but the cooling system does run cooler fron what I have read.
__________________
"The more things change, the more they stay the same."
chrs1961815 is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 12-04-2019, 01:43 PM   #3
alexiskai
Senior Member
 
alexiskai's Avatar
 
Join Date: Apr 2018
Location: Mebane NC
Posts: 2,332
Default Re: High compression head vs cooling

I thought the whole idea was that higher compression makes the combustion more efficient, transforming more energy into power and less into waste heat. So it would create less heat (unless your snazzy new HC head causes you to drive the car faster/longer).
alexiskai is offline   Reply With Quote
Old 12-05-2019, 09:05 AM   #4
Bob Bidonde
Senior Member
 
Bob Bidonde's Avatar
 
Join Date: May 2010
Location: Long Island, NY
Posts: 3,432
Default Re: High compression head vs cooling

In my experience, the engines run cooler due to more efficient power stroke combustion.
__________________
Bob Bidonde
Bob Bidonde is offline   Reply With Quote
Old 12-05-2019, 09:29 AM   #5
rotorwrench
Senior Member
 
rotorwrench's Avatar
 
Join Date: Jun 2010
Location: San Antonio, Texas
Posts: 16,371
Default Re: High compression head vs cooling

Combustion efficiency is only one aspect of heat generation. It is also affected by the amount of power that is pulled by the engine or how long it sets at idle. Cooling systems will draw the heat away if they are efficient but setting at idle has less air flow than running down the road. If you consistently pull heavier loads or try to get higher speeds than normal then more heat will be generated. With more power there is always more heat under load. Normal driving will have less affect and the difference may be negligible.
rotorwrench is offline   Reply With Quote
Old 12-05-2019, 09:50 AM   #6
old31
Senior Member
 
Join Date: Jan 2016
Posts: 2,088
Default Re: High compression head vs cooling

Sponsored Links (Register now to hide all advertisements)
When I installed my 6.1 head I had overheat problems at long highway speeds, as before I did not have a problem. I had the radiator cleaned out and flow tested and the shop said it was good. I reinstalled it and I had the same issues.

I installed a Bergs radiator and that solved the problems. Today I can run in 95 degree temps at 55 mph all day long.
old31 is offline   Reply With Quote
Old 12-05-2019, 02:02 PM   #7
Russ/40
Senior Member
 
Russ/40's Avatar
 
Join Date: May 2010
Location: Santee, California
Posts: 3,505
Default Re: High compression head vs cooling

My experience mirrors Old31's. The Berg's a terrific radiator. My truck runs so cool I can't really make an observation for the 6.1 head other than it feels like 60hp, not 40. I suppose a light truck has something to do with that. I'm elated with my truck now.
Russ/40 is offline   Reply With Quote
Old 12-05-2019, 08:23 PM   #8
gary678*
Senior Member
 
Join Date: Dec 2016
Location: Middletown, NY
Posts: 162
Default Re: High compression head vs cooling

I have a 5.5 head and a 160 degree thermostat with a 50/50 blend of antifreeze. On a hot summer day up a long steep hill on NY's Bear Mountain (2.0 miles+) at 45 MPH the temp went to 170; on the downhill side it dropped to 150. Otherwise it runs at a steady 160. My guess is that if you develop a heating problem that the cause is probably not the head but something such as a blown head gasket with the loss of coolant, or simply a deficient radiator or water pump, or more. Gary
gary678* is offline   Reply With Quote
Old 12-06-2019, 10:08 AM   #9
old31
Senior Member
 
Join Date: Jan 2016
Posts: 2,088
Default Re: High compression head vs cooling

I agree with Gary.

I am also running 50/50 mix but with a 180 tstat.
old31 is offline   Reply With Quote
Old 12-07-2019, 07:02 AM   #10
chap52
Senior Member
 
chap52's Avatar
 
Join Date: Jun 2013
Location: Marana Arizona
Posts: 1,771
Default Re: High compression head vs cooling

6:1 Snyders head, 160 thermostat, 50/50 mix. Runs cooler than it did with stock set-up. Chap
chap52 is offline   Reply With Quote
Old 12-07-2019, 07:28 AM   #11
Alaska Mike
Member
 
Join Date: Sep 2013
Location: Centerville, Iowa
Posts: 91
Default Re: High compression head vs cooling

As a sort of other question about high compression heads, I have been considering one, but was told that it is sometimes difficult to get the engine to idle properly with a high compression head. Have any of you experienced that problem?
Alaska Mike is offline   Reply With Quote
Old 12-07-2019, 09:49 AM   #12
old31
Senior Member
 
Join Date: Jan 2016
Posts: 2,088
Default Re: High compression head vs cooling

Alaska I have not had any idle problems since I installed the 6.1.

One thing I have noticed since I did my engine work (larger intake valves, touring cam, model b carb, bored intake, bored cylinders, v8 clutch, lightened flywheel) is that I have lost the famous model a chug chug chug at idle. I do miss that sound. The car sounds more like a modern car.

But the gain is well worth the idle sounds of chug chug chug.
old31 is offline   Reply With Quote
Old 12-07-2019, 10:43 AM   #13
Purdy Swoft
Senior Member
 
Purdy Swoft's Avatar
 
Join Date: May 2010
Location: Alabama
Posts: 8,099
Default Re: High compression head vs cooling

I'm still running 5.9 compression heads on some of my model A's and they run cooler than original .
Purdy Swoft is offline   Reply With Quote
Old 12-07-2019, 01:54 PM   #14
Russ/40
Senior Member
 
Russ/40's Avatar
 
Join Date: May 2010
Location: Santee, California
Posts: 3,505
Default Re: High compression head vs cooling

Quote:
Originally Posted by Alaska Mike View Post
As a sort of other question about high compression heads, I have been considering one, but was told that it is sometimes difficult to get the engine to idle properly with a high compression head. Have any of you experienced that problem?
I can't give any credibility to that. I think its non-sense. Just take the time to make carb adjustments, you should make with any equipment change.
Russ/40 is offline   Reply With Quote
Old 12-07-2019, 02:50 PM   #15
wensum
Senior Member
 
wensum's Avatar
 
Join Date: Apr 2011
Location: New Zealand
Posts: 444
Default Re: High compression head vs cooling

Quote:
Originally Posted by Alaska Mike View Post
As a sort of other question about high compression heads, I have been considering one, but was told that it is sometimes difficult to get the engine to idle properly with a high compression head. Have any of you experienced that problem?


Our motor has a 7:1 head and considerably lightened flywheel plus dual Strombergs and the motor can idle as smoothly and slowly as a standard Model A.
wensum is offline   Reply With Quote
Old 12-07-2019, 05:05 PM   #16
Purdy Swoft
Senior Member
 
Purdy Swoft's Avatar
 
Join Date: May 2010
Location: Alabama
Posts: 8,099
Default Re: High compression head vs cooling

Besides the 5.9 head , I run the super street Winfield 3/4 race cam , lighter model B flywheel , dual updraft model B carburetors and a few other minor mods . My model A idles smoothly and has the normal model A cackle at idle with the spark retarded . My car may not idle exactly as slow as a completely stock engine but it will idle purdy slow
Purdy Swoft is offline   Reply With Quote
Old 12-07-2019, 08:08 PM   #17
dumb person
Senior Member
 
dumb person's Avatar
 
Join Date: Apr 2011
Location: South pacific island
Posts: 1,724
Default Re: High compression head vs cooling

Depends if your head is alloy or iron.

"Alloy is for boiling water.
Iron is for power."

It was told to me that the alloy heads conduct the heat into the water faster, which is true. Hence robbing power & creating heat in the cooling system.
__________________
<Link> This is how we roll<Link>

"I'm Convinced that no one really reads posts anymore; they just fabricate what they think the post says then ramble on about red herrings."--Bob
Outcasts rules of old cars
#1 Fun is imperative, mainstream is overrated
#2 If they think it is impossible, prove them wrong
#3 If the science says it impossible you are not being creative enough.
#4 No shame in recreating something you never had
#5 If it were not for the law & physics you would be unstoppable
dumb person is offline   Reply With Quote
Old 12-07-2019, 09:57 PM   #18
Purdy Swoft
Senior Member
 
Purdy Swoft's Avatar
 
Join Date: May 2010
Location: Alabama
Posts: 8,099
Default Re: High compression head vs cooling

My heads are all cast iron . I prefer cast iron for durability , A lot of people have been running the Thomas finned aluminum heads for years , the aluminum heads must be doing some good or people wouldn't continue using them . Hot rods with flathead V8s have been using aluminum heads forever . As expensive as higher compression heads are , I want mine to last as long as possible . I've never had a problem with cast iron .
Purdy Swoft is offline   Reply With Quote
Old 12-08-2019, 10:42 AM   #19
old31
Senior Member
 
Join Date: Jan 2016
Posts: 2,088
Default Re: High compression head vs cooling

Purdy and Wen, like me, have you lost the Model A chug chug chug at slow idle, or do you still have it.
old31 is offline   Reply With Quote
Old 12-08-2019, 12:16 PM   #20
Purdy Swoft
Senior Member
 
Purdy Swoft's Avatar
 
Join Date: May 2010
Location: Alabama
Posts: 8,099
Default Re: High compression head vs cooling

Mine still has the model A cackle or chick ah lunk as I call it at idle. They might not idle exactly as slowly as original , but they idle pretty slow with the spark retarded .
Purdy Swoft is offline   Reply With Quote
Old 12-09-2019, 11:37 AM   #21
Jim Brierley
Senior Member
 
Join Date: Jun 2010
Location: Temecula, CA
Posts: 4,066
Default Re: High compression head vs cooling

Aluminum does transfer heat more quickly than iron, but the amount of heat generated does not change, so does not affect engine temp. More compression does make the engine more efficient, so more power and less fuel used, but that can vary depending amount of throttle being used. Iron does last longer but aluminum is easier to repair if needed.
Jim Brierley is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 03:04 AM.