|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
10-25-2021, 11:55 AM | #1 |
Member
Join Date: Mar 2017
Location: Ontario, Canada
Posts: 54
|
Bolts for Pickup Box to Frame (1939)
Hi All,
I am hoping someone here can help me out... The box on my 1939 P/U rests on boards which are bolted to the frame. In between the boards and the frame, the truck uses Wooden cross members which raise the box up off the frame at the front and at the rear. I believe carriage bolts, about 8" long, are used to hold this all together. They appear to be 7/16" diameter (hard to say as they are pretty much non-existent now). My problem is that I have searched high and low for 7/16" x 8" carriage bolts and have had no luck in sourcing them. This seems strange as they are available in 3/8" diameter and 1/2" diameter (the guy at the fastener store says that nobody uses 7/16"). I would not feel safe holding the bed in place with 3/16" and 1/2" is too big for the holes in the steel part of the frame. Does anybody know where I can get these? thanks, George |
10-25-2021, 12:18 PM | #2 |
Senior Member
Join Date: May 2010
Location: Solihull, England.
Posts: 8,755
|
Re: Bolts for Pickup Box to Frame (1939)
I used metric on my 41. Not sure if I used 10mm or 12mm. Would something like that be more available there?
|
Sponsored Links (Register now to hide all advertisements) |
|
10-25-2021, 12:58 PM | #3 |
Senior Member
Join Date: Feb 2017
Location: Rochester Wa
Posts: 574
|
Re: Bolts for Pickup Box to Frame (1939)
|
10-25-2021, 01:03 PM | #4 |
Senior Member
Join Date: Apr 2014
Location: Minnesota
Posts: 1,166
|
Re: Bolts for Pickup Box to Frame (1939)
You could always go with a kit if you cant find them locally.
https://www.horkeyswoodandparts.com/....php#boxoframe |
10-25-2021, 05:06 PM | #5 |
Senior Member
Join Date: May 2010
Location: southeastern Michigan
Posts: 10,101
|
Re: Bolts for Pickup Box to Frame (1939)
Michael Driskell at thirdgenauto.com likely has them in the correct length and thread count.
|
10-26-2021, 09:26 AM | #6 |
Member
Join Date: Mar 2017
Location: Ontario, Canada
Posts: 54
|
Re: Bolts for Pickup Box to Frame (1939)
Sponsored Links (Register now to hide all advertisements)
Cheers, George |
10-28-2021, 07:41 AM | #7 |
Senior Member
Join Date: May 2010
Location: Edgefield, SC
Posts: 811
|
Re: Bolts for Pickup Box to Frame (1939)
Do the long bolts you are looking for to use on your 39 have the square hole in the top like the ones used on 35-37 pickup beds?
|
10-28-2021, 08:16 AM | #8 | |
Senior Member
Join Date: Mar 2014
Location: Jacksonville FL
Posts: 3,963
|
Re: Bolts for Pickup Box to Frame (1939)
Quote:
Bolts are my business. Mike and I have had conversations about these particular bolts you require......THERE are two major issues you are facing. 1) The "majority" of fastener suppliers and fastener manufacturers are producing products for the "Industrial" market NOT the "Automotive" market and 7/16 & 9/16 are NOT commonly used diameters in the "Industrial" world (IF at all) . WHY automotive manufacturers/Engineers use 7/16 & 9/16 I have NO clue......WHY they just can't either increase OR decrease the diameter of the bolt is beyond me?? 2)There are a few manufacturer's I deal with that could "certainly" make these items, NO problem......The problem lies in the quantity. The "cost" of set up of the machinery to make them is "HIGH" and the quantity needed for "stock" is cost prohibitive.......SO its a "demand" issue, Unfortunately!!!!! AS you can figure, the amount needed to make the price palatable would supply the need for two life times of demand. This doesn't help you I know BUT this is how it is!! |
|
10-28-2021, 06:43 PM | #9 |
Senior Member
Join Date: May 2010
Location: Wisconsin, USA
Posts: 9,007
|
Re: Bolts for Pickup Box to Frame (1939)
When I needed these for the '40 pickup restoration I'd done, I'd purchased the reproduction bolts from Mac's. They were of course, much too short for the required application but had the proper head, diameter and thread count.
It was an easy task to cut the "center section" out of the repop bolts, weld in the additional length of shaft needed, re-plate and done.
__________________
"I can explain it for you. However, I can't understand it for you". |
10-28-2021, 09:36 PM | #10 | |
Senior Member
Join Date: May 2010
Location: MN
Posts: 7,053
|
Re: Bolts for Pickup Box to Frame (1939)
Quote:
On the 38 truck there was the square tool flat top bolts. 38-39 share a lot of the same items. 38 had a metal bed floor. Not sure on 39. When I was looking for them, a long while back. Roy told me they are not being made by anyone. In a coffee can I have most of the original bolts, some had to be cut out. There is a cast wegdes also to square the bolt to the frame. Kube makes a good point that with a cutoff and a tig you can salvage for an original look. Or just use the best that are available currently. Last edited by Tinker; 10-28-2021 at 10:34 PM. |
|
10-29-2021, 06:53 AM | #11 |
Senior Member
Join Date: Mar 2014
Location: Jacksonville FL
Posts: 3,963
|
Re: Bolts for Pickup Box to Frame (1939)
IF someone has the "correct" length (OR If it is for sure 8") I will be happy to check with my two specialty manufacturers and see just what they would cost to have made...what the quantity break might be....etc etc. AS for the thread count I don't think that would make a difference being course thread instead of Fine, correct??? AS course thread is WAY more common in my world of fasteners.
HOW many per truck are needed to, that way I can figure a quantity based on a sets of them?? |
10-29-2021, 09:27 AM | #12 |
Senior Member
Join Date: Dec 2013
Location: Minnesota, Florida Keys
Posts: 10,319
|
Re: Bolts for Pickup Box to Frame (1939)
Come to think of it, I can't remember ever seeing a fine-thread carriage bolt.
|
10-29-2021, 10:27 AM | #13 | |
Senior Member
Join Date: May 2010
Location: Wisconsin, USA
Posts: 9,007
|
Re: Bolts for Pickup Box to Frame (1939)
Quote:
The bed to frame bolts (PU) are fine thread as well.
__________________
"I can explain it for you. However, I can't understand it for you". |
|
10-29-2021, 10:29 AM | #14 |
Senior Member
Join Date: Mar 2014
Location: Jacksonville FL
Posts: 3,963
|
Re: Bolts for Pickup Box to Frame (1939)
|
10-29-2021, 02:41 PM | #15 |
Senior Member
Join Date: May 2010
Location: Beaver Dam, Wisconsin
Posts: 821
|
Re: Bolts for Pickup Box to Frame (1939)
My turn! These are the remaining original bolts from my '39 pickup bed. I was there on that day when my "pop's" and brothers thought we should take the fenders, running boards off my pickup that was used on my Grandparents farm. This happened in 1981 best I can guess. Since the other pieces were off we proceeded to remove the bed bolts as well. Wish we had never done this as the pickup, although being very abused, was mostly original. I have a repro bed with the inaccurate wood floor instead of steel per my wishes but still have one side of those original bolts. Front most is a long carriage bolt while the rest have the taper top with the square indentation for tightening, all fine thread. Hope this helps.
|
10-29-2021, 03:11 PM | #16 | |
Senior Member
Join Date: May 2015
Posts: 8,150
|
Re: Bolts for Pickup Box to Frame (1939)
Quote:
__________________
The only thing nice about being imperfect is the joy it brings to others.... "Silver rings, your butt! Them's washers!" "We shot our way out of that town for a dollar's worth of steel holes!" - from 'The Wild Bunch' - 1969 https://www.youtube.com/watch?v=7NReUd2_0u0 |
|
10-29-2021, 03:16 PM | #17 | |
Senior Member
Join Date: Mar 2014
Location: Jacksonville FL
Posts: 3,963
|
Re: Bolts for Pickup Box to Frame (1939)
Quote:
|
|
10-29-2021, 07:20 PM | #18 |
Senior Member
Join Date: May 2010
Location: Beaver Dam, Wisconsin
Posts: 821
|
Re: Bolts for Pickup Box to Frame (1939)
Not a "bucket tooth" bolt on the the 3 tapered head bolts, a smooth taper on all. You got the thread length correct on basically all the tapered head bolts 1 1/2 inches give or take a bit with the long carriage bolt having threads of 1 3/8 inches.
|
10-30-2021, 11:07 PM | #19 |
Senior Member
Join Date: May 2010
Location: MN
Posts: 7,053
|
Re: Bolts for Pickup Box to Frame (1939)
Great post GaryU and pictures.
|
12-01-2021, 09:32 AM | #20 |
Member
Join Date: Mar 2017
Location: Ontario, Canada
Posts: 54
|
Re: Bolts for Pickup Box to Frame (1939)
Thanks for everybody's input...
I've decided to TIG weld a set of bolts for my truck. I can get the exact length I need and use fine thread "donor bolts". I will fab up a little "jig" to ensure they are straight. I can get Grade 5 Carriage Bolts which should suffice. Cheers, George |
|
|
Sponsored Links (Register now to hide all advertisements) |
|