|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
10-13-2017, 02:50 PM | #1 |
Junior Member
Join Date: Mar 2013
Posts: 4
|
1940 Ford front I-beam axle
I acquired a NOS 1940 Ford I-beam axle. Before I install into the wishbone, is there a front or back to the axle?
The kingpin lock bolts fit front or back exactly the same. |
10-13-2017, 04:54 PM | #2 |
Senior Member
Join Date: May 2010
Location: Solihull, England.
Posts: 8,745
|
Re: 1940 Ford front I-beam axle
My understanding is that there is no back or front side.
Mart. |
Sponsored Links (Register now to hide all advertisements) |
|
10-13-2017, 04:55 PM | #3 |
Senior Member
Join Date: May 2010
Location: Minnesota
Posts: 1,825
|
Re: 1940 Ford front I-beam axle
No front or back to the axle.
|
10-13-2017, 05:29 PM | #4 |
Senior Member
Join Date: May 2010
Location: East Shore of LAKE HOUSTON
Posts: 11,106
|
Re: 1940 Ford front I-beam axle
Even though there are a few hold-outs that refuse to believe this (because they find difficulty installing the king pin LOCKING PINS), as Mart and rich b said above...there is NO front or rear side. The axles are symmetrical! DD
|
10-13-2017, 05:51 PM | #5 |
Senior Member
Join Date: May 2010
Location: London On, Can.
Posts: 377
|
Re: 1940 Ford front I-beam axle
I suggest there is a front and rear .any stamping information or embossed lettering that is found on the boss of the axle close to the one end ,the axle should be placed with the embossed lettering to the right front.
|
10-13-2017, 05:59 PM | #6 |
Member Emeritus
Join Date: Nov 2012
Location: Wichita KS
Posts: 16,132
|
Re: 1940 Ford front I-beam axle
Sponsored Links (Register now to hide all advertisements)
|
10-13-2017, 06:05 PM | #7 |
Senior Member
Join Date: Jul 2011
Location: SF Bay Area
Posts: 6,635
|
Re: 1940 Ford front I-beam axle
Actually, there is a front and back. Once you get the axle installed, get down low, directly in front of the car and look at the axle. The side you can see from that angle is the front.
__________________
Alan |
10-13-2017, 06:12 PM | #8 |
Member Emeritus
Join Date: Nov 2012
Location: Wichita KS
Posts: 16,132
|
Re: 1940 Ford front I-beam axle
|
10-13-2017, 06:15 PM | #9 |
Senior Member
Join Date: Jan 2012
Location: Lyman,ME.
Posts: 2,623
|
Re: 1940 Ford front I-beam axle
That’s a sense of humor I can relate too!!!!!.... Mark
__________________
I'm thinkin' about crankin' My ragged ol' truck up and haulin' myself into town. Billy Joe Shaver |
10-13-2017, 06:24 PM | #10 |
Senior Member
Join Date: May 2010
Location: East Shore of LAKE HOUSTON
Posts: 11,106
|
Re: 1940 Ford front I-beam axle
johnny.......Could you possibly post a picture of said stamping or embossing on a '37-'41 Ford axle? I'm specifically NOT referring to a "heavy" 1932 axle. DD
|
10-13-2017, 06:28 PM | #11 |
Senior Member
Join Date: May 2010
Location: Coral Springs FL
Posts: 10,925
|
Re: 1940 Ford front I-beam axle
This has been debated before. There is no "FRONT". Both sides are the same.
|
10-13-2017, 07:23 PM | #12 |
Senior Member
Join Date: May 2010
Location: London On, Can.
Posts: 377
|
Re: 1940 Ford front I-beam axle
I agree.all that there is no difference with a new axle ,however from factory I suggest that the axle was installed with the Ford stamp and part #,facing the front [right side] Where one should be careful is when restoring a car,taking the front end apart: one could install the axle reversed as it is quite likely that some time in the cars life an attempt was made to bend the axle ends to correct an alignment problem putting it in reversed would create a bad steering condition.
|
10-13-2017, 07:40 PM | #13 | |
Senior Member
Join Date: May 2010
Location: Napa,California
Posts: 6,029
|
Re: 1940 Ford front I-beam axle
Quote:
|
|
10-13-2017, 10:21 PM | #14 |
MEMBER EMERITUS
Join Date: May 2010
Location: New Zealand
Posts: 1,380
|
Re: 1940 Ford front I-beam axle
Bit like the old story about how to tell the back of a tree from the front.
Look where someone's taken a dump. That's the back. |
10-14-2017, 04:14 AM | #15 |
Senior Member
Join Date: May 2010
Location: Solihull, England.
Posts: 8,745
|
Re: 1940 Ford front I-beam axle
Difficulty in fitting the kingpin cotter pins in is probably real. It happened to me. I rebuilt the front end on my 41 pickup and reversed the axle when putting it back together. One cotter pin went in slightly tight, but hammered home nicely. the other did not want to go in. I ran a 9/16" drill through the hole to remove any burrs or corrosion etc. and the pin went in fine. I should have done that first on the first hole.
So saying the cotters don't want to go in if it is the "wrong" way round is probably true, but it is only because the pins were previously in the other way around and have raised a burr or some other slight imperfection. Mart. |
10-14-2017, 07:31 AM | #16 |
Junior Member
Join Date: Mar 2013
Posts: 4
|
Re: 1940 Ford front I-beam axle
Thank you everyone for the quick responses and the information.
|
10-14-2017, 09:50 AM | #17 |
Member Emeritus
Join Date: Nov 2012
Location: Wichita KS
Posts: 16,132
|
Re: 1940 Ford front I-beam axle
|
10-14-2017, 10:14 AM | #18 |
Senior Member
Join Date: May 2010
Location: Solihull, England.
Posts: 8,745
|
Re: 1940 Ford front I-beam axle
Guess it must be. When I was a kid the similar setup holding the pedal cranks on our bikes was called a cotter pin.
Mart. |
10-14-2017, 10:19 AM | #19 |
Member Emeritus
Join Date: Nov 2012
Location: Wichita KS
Posts: 16,132
|
Re: 1940 Ford front I-beam axle
Thanks Mart, it is interesting the different terms that are used in different areas for automotive parts and tools. This is what I have always referred to as a cotter pin.
|
10-14-2017, 10:29 AM | #20 |
Member Emeritus
Join Date: Nov 2012
Location: Wichita KS
Posts: 16,132
|
Re: 1940 Ford front I-beam axle
Yep, looks like a common British term.
|
|
|
Sponsored Links (Register now to hide all advertisements) |
|