|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
09-11-2022, 06:44 PM | #1 |
Junior Member
Join Date: Feb 2015
Posts: 20
|
Help ID Dual Exhaust Manifold
Need some help to identify application for the manifolds in the pictures.
Their not quite the same although they dump in the same location. Not 49-51 nor 52-53 car, don't know about truck Number on the one doesn't get me any ID. No markings on the other. |
09-11-2022, 08:56 PM | #2 |
Senior Member
Join Date: May 2010
Location: East Hartford, Ct
Posts: 5,898
|
Re: Help ID Dual Exhaust Manifold
In as much as these both look like they are meant for the drivers side.
They look like aftermarket parts to allow installation of dual exhaust. As for no markings, probably because they were fabricated by two different manufacturers. (my guess) They would probably work on just about all V8's. Another thought, they might have been part of a 'Police car' package.
__________________
DON'T RECALL DOING SOMETHING FOR MYSELF BASED ON SOMEONE ELSE'S LIKES OR DISLIKES Last edited by 51 MERC-CT; 09-12-2022 at 02:05 AM. |
Sponsored Links (Register now to hide all advertisements) |
|
09-12-2022, 11:23 AM | #3 |
Junior Member
Join Date: Feb 2015
Posts: 20
|
Re: Help ID Dual Exhaust Manifold
No doubt they are after market parts. Issue of steering box clearance is the concern and yes they would fit any flathead V-8 motor but only in specific vehicles. It's the correct vehicle application that I'm trying to sort out.
|
09-12-2022, 05:16 PM | #4 |
Senior Member
Join Date: Feb 2011
Location: Buchanan, MI
Posts: 676
|
Re: Help ID Dual Exhaust Manifold
'49- '51 Ford passenger car dual side exhaust manifold, aftermarket.
'52- '53 are different. |
09-12-2022, 05:39 PM | #5 |
Senior Member
Join Date: Jan 2012
Location: Lyman,ME.
Posts: 2,630
|
Re: Help ID Dual Exhaust Manifold
These are my after market dual manifolds on my ‘51 Ford. I would guess from different manufacturers. I have another left one that was sold to me as a Ford manifold and it looks identical to my after market one. That only means they used a Ford one for the pattern.....Mark
__________________
I'm thinkin' about crankin' My ragged ol' truck up and haulin' myself into town. Billy Joe Shaver |
09-12-2022, 05:42 PM | #6 |
Senior Member
Join Date: Jan 2012
Location: Lyman,ME.
Posts: 2,630
|
Re: Help ID Dual Exhaust Manifold
Sponsored Links (Register now to hide all advertisements)
__________________
I'm thinkin' about crankin' My ragged ol' truck up and haulin' myself into town. Billy Joe Shaver |
09-12-2022, 06:05 PM | #7 |
Senior Member
Join Date: May 2010
Posts: 2,488
|
Re: Help ID Dual Exhaust Manifold
Drake made ONE run each of these: separate types 49-51 and the other 52-53 Newc
|
09-12-2022, 10:41 PM | #8 |
Junior Member
Join Date: Feb 2015
Posts: 20
|
Re: Help ID Dual Exhaust Manifold
The manifolds in my pictures do not fit 49-51. They would interfere with the steering box. I have 49-51 units and the dump flange is much farther back.
Flatford 8. Does what you show for a LH manifold clear the steering, can't tell from the pictures if exhaust pipe is connected. Here is another picture of how they compare: Last edited by Old Magnet; 09-12-2022 at 10:48 PM. |
09-13-2022, 07:40 AM | #9 |
Senior Member
Join Date: Jan 2012
Location: Lyman,ME.
Posts: 2,630
|
Re: Help ID Dual Exhaust Manifold
It’s close but it does clear. This car has a T-5 so I made sure of the clearance when I modified the cross member.........Mark
__________________
I'm thinkin' about crankin' My ragged ol' truck up and haulin' myself into town. Billy Joe Shaver |
|
|
Sponsored Links (Register now to hide all advertisements) |
|