|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
11-13-2015, 07:15 PM | #1 |
Senior Member
Join Date: May 2010
Location: Napier, New Zealand
Posts: 2,001
|
Vacuum gauge reading.
Finally got a vacuum gauge hooked up, and it's giving a steady reading of about 6 at idle. According to the interweb, this is the symptom of an intake leak. I had a new gasket on it, and all intake bolts were tight, same for the carb to manifold. I have taken the intake off, and the gasket looks fine, perhaps I need to face the surface of the manifold. Any comments on this?
|
11-13-2015, 07:41 PM | #2 |
Member Emeritus
Join Date: Nov 2012
Location: Wichita KS
Posts: 16,132
|
Re: Vacuum gauge reading.
Well, the only comment I have is that is quite a leak! I would start with the intake.
|
Sponsored Links (Register now to hide all advertisements) |
|
11-13-2015, 08:04 PM | #3 |
Senior Member
Join Date: Oct 2011
Location: Shelton, WA
Posts: 3,800
|
Re: Vacuum gauge reading.
What year intake? Are you sure all the vacuum ports are either used or plugged (including any on the carb)? I would think you would hear a leak large enough to only have a reading of 6. If you check the manifold and it is flat, use a new gasket with some spray on high tack on both sides and torque it down in steps from the center out. Also look at the underside of the manifold sealing surface for defects.
|
11-13-2015, 08:39 PM | #4 |
Senior Member
Join Date: May 2010
Location: West Michigan
Posts: 1,218
|
Re: Vacuum gauge reading.
Are you running a stock or aftermarket cam?
Tom |
11-13-2015, 08:42 PM | #5 |
Senior Member
Join Date: May 2010
Location: Palmer, Alaska
Posts: 1,575
|
Re: Vacuum gauge reading.
If you have Vac. wipers disconnect the hose at the manifold and plug the manifold source and check again
|
11-13-2015, 09:16 PM | #6 |
Senior Member
Join Date: Oct 2013
Location: Glens Falls NY
Posts: 1,267
|
Re: Vacuum gauge reading.
Sponsored Links (Register now to hide all advertisements)
PS .... if possible confirm your readings by checking gauge connection and using another vac guage. |
11-13-2015, 09:22 PM | #7 |
Senior Member
Join Date: May 2010
Location: Masterton, New Zealand
Posts: 3,832
|
Re: Vacuum gauge reading.
Y'know Marty, when I first read your other post, the first thing that came to my mind was vacuum leak. I didn't respond, because someone else suggested same thing. One thing that sticks in my mind from when I was a young fella, was reading once in a NZ Hot Rod Magazine about Rob Campbell trying to cure a poor running flathead. Tried everything, finally coated the inlet manifold gasket with grease, and, viola!! it ran sweet. Since that day, I have always done the same. Think about it, it allows the surfaces to slide over each other as they're torqued, any that oozes inside the engine will do no harm, and in the future, it allows one to easily remove and even reuse the gasket.
I know where you live; about 20 feet above sea level, you're running a stock cam, at idle you should be seeing 20-21 ins Hg on the gauge!
__________________
Unfortunately, two half wits don't make a whole wit! |
11-14-2015, 03:43 AM | #8 |
Senior Member
Join Date: May 2010
Location: Napier, New Zealand
Posts: 2,001
|
Re: Vacuum gauge reading.
Update: I ran a flat file over the underneath surface of the intake manifold, and it was all over the place. I attacked it with great gusto, and had to actually take quite a bit off to get it flat. As well as not being flat, there were a lot of little gouges from the ports out to the edge. I kept flat-filing until it was smooth and close to flat, and I'll assemble it with a liberal coating of grease (thanks Brian). fingers crossed.
|
11-14-2015, 06:09 AM | #9 |
Senior Member
Join Date: May 2010
Posts: 4,750
|
Re: Vacuum gauge reading.
Do I remember correctly, three 94's with the front and rear blocked?
|
11-14-2015, 07:39 AM | #10 |
Senior Member
Join Date: Aug 2012
Location: Perth, Western Australia
Posts: 2,687
|
Re: Vacuum gauge reading.
You have a cam and multiple carbs?
__________________
"Came too close to dying to stop living now!" |
11-14-2015, 09:42 AM | #11 |
Senior Member
Join Date: Jan 2011
Location: Central Ohio
Posts: 5,064
|
Re: Vacuum gauge reading.
Another trick is to get something like "starter fluid" . . . and with the engine idling, spray some of it around the manifold - see if the RPM changes. Now don't spray too much and get the engine on fire!
It definitely sounded like you had a vacuum leak - 6 ins is a number that you should not see unless you opened up multiple carbs all at once . . . |
11-14-2015, 11:31 AM | #12 |
Senior Member
Join Date: Dec 2012
Location: Massillon, Ohio
Posts: 783
|
Re: Vacuum gauge reading.
And if you are going to use starting fluid in this manner have a fire extinguisher at your feet !!
|
11-14-2015, 01:06 PM | #13 |
Senior Member
Join Date: Sep 2013
Posts: 1,027
|
Re: Vacuum gauge reading.
Why not just use water in spray bottle?
|
11-14-2015, 01:11 PM | #14 |
Senior Member
Join Date: May 2010
Location: East Shore of LAKE HOUSTON
Posts: 11,107
|
Re: Vacuum gauge reading.
Using a flammable substance changes the sound and the engine RPMs when sprayed onto the vac leak.
Using starting fluid (usually ether)....well, that stuff is explosively-volatile. DD |
11-14-2015, 01:36 PM | #15 | |
Senior Member
Join Date: May 2013
Location: Pa.
Posts: 2,166
|
Re: Vacuum gauge reading.
Quote:
It's for high temperature applications.
__________________
Nomad |
|
11-14-2015, 02:13 PM | #16 |
Senior Member
Join Date: May 2010
Location: Palmer, Alaska
Posts: 1,575
|
Re: Vacuum gauge reading.
It may be better to check for a vac. leak around the carb, and intake area with a propane torch bottle with a hose on it to direct the flow of propane to the suspected area's. I use this method on Eng.'s that have paint, or other coatings that I do not want to damage. I also use Berrymans spray B12 Chemtool carb cleaner, but it will attack (eat) paint, and you have to be careful that you don't catch something on fire. be warned that using the chemtool, that if you use a lot it will run off the eng and puddle under the car and may catch fire. it has happened to me. this chemtool method seems to work the best, but it is the most hazardous and is the most destructive to paint. which ever way you choose just be aware of a fire hazard.
|
11-14-2015, 02:14 PM | #17 |
Senior Member
Join Date: May 2010
Location: SPEEDWAY INDIANA
Posts: 4,148
|
Re: Vacuum gauge reading.
A couple vacuum leak tests we have used over the years.
1-Use propane with engine running and hold propane ( old torch etc) and apply around the intake, carbs etc . Engine will speed up usually when leak is found. Note engine will slow down when carbs ar too rich. 2-Hook vacuum gauge to dipstick tube when running any vacuum ay all show intake leak internally under side of intake... |
|
|
Sponsored Links (Register now to hide all advertisements) |
|