|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
02-13-2017, 02:14 PM | #1 |
Senior Member
Join Date: May 2010
Posts: 295
|
New-Revised RG & JS
I did not receive pages 13 thru 16 of Area 10 (Glass and Side Curtains) in my package of Revised RG & JS changes.
Did any of you miss those changes too? If so, what is the proper address to request those 4 pages? Thanks. Bill Lee/Virginia Peninsula |
02-13-2017, 02:20 PM | #2 |
Senior Member
Join Date: May 2010
Location: Glendale, AZ
Posts: 2,953
|
Re: New-Revised RG & JS
It stops at 10-12 in mine also
|
Sponsored Links (Register now to hide all advertisements) |
|
02-13-2017, 02:22 PM | #3 |
Senior Member
Join Date: May 2010
Posts: 295
|
Re: New-Revised RG & JS
Joop:
Thank you sir. Regards, Bill Lee/Virginia Peninsula |
02-13-2017, 02:37 PM | #4 |
Senior Member
Join Date: Apr 2015
Location: Boise, Idaho
Posts: 1,578
|
Re: New-Revised RG & JS
My revised section 10 ends at 10-12 also, but I scanned through the index a couple of times and don't see any pages beyond 10-12 referenced.....maybe 10-12 is the last page?
__________________
Early '29 CCPU that had a 4-speed, but not any more.......in the family since '62 |
02-13-2017, 02:48 PM | #5 |
Senior Member
Join Date: May 2010
Location: Young Harris, GA
Posts: 1,821
|
Re: New-Revised RG & JS
Area 10 is a complete, standalone new set of new pages. It ends at page 10-12. You are not missing anything.
.
__________________
Jim Cannon Former MAFCA Technical Director "Have a Model A day!" |
02-13-2017, 03:18 PM | #6 |
Senior Member
Join Date: May 2010
Location: Glendale, AZ
Posts: 2,953
|
Re: New-Revised RG & JS
Sponsored Links (Register now to hide all advertisements)
Area 10 (Glass and Side Curtains) Insert with new area 10 (pages 10-1 thru 10-16) Misprint in the instructions for inserting Revision 4 |
02-13-2017, 03:26 PM | #7 |
Senior Member
Join Date: Apr 2015
Location: Boise, Idaho
Posts: 1,578
|
Re: New-Revised RG & JS
My instruction page was still in the recycle bin..
Sure enough, 10-16 was crossed out and 12 written in...
__________________
Early '29 CCPU that had a 4-speed, but not any more.......in the family since '62 |
02-13-2017, 04:28 PM | #8 |
Senior Member
Join Date: May 2010
Location: Young Harris, GA
Posts: 1,821
|
Re: New-Revised RG & JS
OK, that explains it then. My instruction sheet refers to pages 10–1 through 10–12. I must've obtained a later version of the instructions.
BTW, the back of my instruction sheet also says that there is a typo on the new 2016 version of page 1-11, and that I should replace it with the loose page 1-11 and 1-12 enclosed. (Typos will happen.) If your Rev. 4 pack says page "1-11 Revised 2016" at the bottom and it does NOT have the word Carburetor in bold at the top left of the page, you do not have the corrected page. Let me know at [email protected] and I will make arrangements to get the corrected page to you. .
__________________
Jim Cannon Former MAFCA Technical Director "Have a Model A day!" Last edited by Jim/TX/GA; 02-13-2017 at 05:08 PM. |
02-13-2017, 06:27 PM | #9 |
Senior Member
Join Date: Apr 2015
Location: Boise, Idaho
Posts: 1,578
|
Re: New-Revised RG & JS
Ok....I fished the loose page out of the recycle bin. I don't know how it got there...
The one with carburetor in bold at the top and 1-11 revised 2016 at the bottom. This is the correct page? Thanks!
__________________
Early '29 CCPU that had a 4-speed, but not any more.......in the family since '62 Last edited by 1955cj5; 02-13-2017 at 06:44 PM. |
02-13-2017, 06:57 PM | #10 |
Senior Member
Join Date: May 2010
Location: Young Harris, GA
Posts: 1,821
|
Re: New-Revised RG & JS
Yes! You need to put that in your binder. Toss the other page 1-11 away that just begins with text that says "and no attempt was made...".
You got it! .
__________________
Jim Cannon Former MAFCA Technical Director "Have a Model A day!" |
|
|
Sponsored Links (Register now to hide all advertisements) |
|