|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
01-26-2017, 12:15 PM | #1 |
Senior Member
Join Date: May 2010
Location: California
Posts: 979
|
Platigage and bearing clearances
I have read lots of opinions on how to check main and rod bearing clearances. There is something that confuses me. It is generally agreed that there should be 0.001" of clearance for each 1.0" of bearing diameter. On a B engine the main bearings are about 2". That would result in a bearing clearance of 0.002". The confusion, for me, is the following. Should the bearing be 0.002" larger than the crank journal? For example, bearing 1.999" and crankshaft journal 1.997". Or is that clearance a 0.002" gap all the way round the journal. Which would make the example bearing 1.999" and the journal 1.995"?
With regard to Plastigage. I have read conflicting instruction. Most say use one piece across the journal. There were also instruction to place two pieces across the journal 180 degrees apart. The first method would give an 0.002" difference (0.001" overall gap) between the bearing and the crank. The second would give a 0.004" difference (0.002" overall gap). I have tried both and the 0.004" difference (0.002" gap) appears to be too much. The crank can be moved up and down producing a rattle noise. What do you guy think? Bob Johnson |
01-26-2017, 12:30 PM | #2 | |
Senior Member
Join Date: May 2010
Location: Central, IL
Posts: 3,968
|
Re: Platigage and bearing clearances
Quote:
to check for roundness yes use it 180* apart but do one strip at a time - do one side get a result and record it, get the plastigauge off 100% clean, then do the other side, get a result and record it - ideally they should match but most likely they wont unless it was fresh bored. take an average and adjust shims accordingly
__________________
1929 Model AA - Need long splash aprons! |
|
Sponsored Links (Register now to hide all advertisements) |
|
01-26-2017, 12:34 PM | #3 |
Senior Member
Join Date: Nov 2011
Location: Sonoma, CA.
Posts: 1,497
|
Re: Platigage and bearing clearances
The bearing should be .002 larger than the crank as in you r first example. The second example is .004 which is too much and why you would have the slop up and down.
Just use one piece of plastigauge too measure the clearance. |
01-26-2017, 12:36 PM | #4 |
Senior Member
Join Date: Jun 2010
Location: Temecula, CA
Posts: 4,089
|
Re: Platigage and bearing clearances
As sea slugs says. You are looking for total clearance. If doing it in-car, put a little upward pressure with a jack under the crank so you get a true reading. .0015 is fine for a B that is not raced.
|
01-26-2017, 12:36 PM | #5 |
Senior Member
Join Date: Mar 2016
Location: Lynden, WA
Posts: 1,564
|
Re: Platigage and bearing clearances
I just went through the process, use a small length of plastigauge, like .25 inch or so. Lay it length-way in line with the crank and away from any openings in the bearings. Put the cap on and torque it properly, don't spin anything! Take the cap off and measure the squished plastigauge. Look for between .001 to .0015 clearance. I'm sure there are other opinions.
|
01-26-2017, 12:42 PM | #6 | |
Senior Member
Join Date: May 2010
Location: Central, IL
Posts: 3,968
|
Re: Platigage and bearing clearances
Sponsored Links (Register now to hide all advertisements)
Quote:
Isnt there a go-nogo method using a piece of tin foil?
__________________
1929 Model AA - Need long splash aprons! |
|
01-26-2017, 12:49 PM | #7 |
Senior Member
Join Date: Mar 2016
Location: Lynden, WA
Posts: 1,564
|
Re: Platigage and bearing clearances
Also might mention to be sure to completely clean the P-G off the cap and journal. Yes I've read of the tin foil method, also just taking out shims until it locks up then put one back in, and even more crude than that. These engines seem to tolerate a lot! If it's not really lose and knocking it's self apart, you're probably good to go.
|
01-26-2017, 12:51 PM | #8 | |
Senior Member
Join Date: May 2010
Location: Central, IL
Posts: 3,968
|
Re: Platigage and bearing clearances
Quote:
__________________
1929 Model AA - Need long splash aprons! |
|
01-26-2017, 12:53 PM | #9 |
Senior Member
Join Date: May 2010
Location: POUGHKEEPSIE NY 12601
Posts: 1,016
|
Re: Platigage and bearing clearances
Bob I have been a self proclaimed mechanic since 1959. I have tried the Platigage route, found it unreliable on Model a engines. I will give you a very brief idea of how I check my bearings. Pull the cap and inspect if the Babbitt appears intact , set the transmission in neutral , spark plugs out of engine, place in hand crank. turn the engine over, it should feel rather free , not lots of resistance, Take off one (Peel off) sliver of shim stock, from each side of the cap. bolt When your happy with one bearing loosen it up then the cap up tight and turn the engine over by the hand crank. If the engine is still free same amount of resistance repeat the procedure till it feels too tight, loosen the cap and put back one sliver of shim. I some times use Prussian blue on the cap to see how well the bearing is fitting. I have goon so far as to scrape the bearing on the high spots, but this is rather difficult if the engine is in the vehicle. You then need to loosen that cap and go on to the next one, same procedure for all rods and mains. You will get a feel for the resistance, just make sure your not over tightening the bearing surface. A good tight fit you can barely move the rods back and forth on the crank shaft. I know I'm opening a can of worms here. But this is the way it was done in the shops years ago. I learned from an old-timer when I was a teenager. Of course the bearing surface of the crank shaft needs to be in good condition, if it's not Again this is a judgement call if it's just a tad bit rough a temporary fix would be to use a strip of sanding material to polish it up, but at this point you would be best to go for rebuilding. Oil pressure is your friend, if there is a lack of it, your in trouble even though your rods are splash oiled. This is my way I'm sure others will pipe in. I have driven Model T's and A' many thousands of miles, With engines adjusted in this manor. The old Dykes Motor manuals have this procedure written in them. You can find one on the web or at swap meets, I just gave one of mine to a youngster intrested in mechanical stuff. JMHO Frank
__________________
|
01-26-2017, 01:06 PM | #10 |
Senior Member
Join Date: Nov 2010
Location: Florham Park, NJ
Posts: 396
|
Re: Platigage and bearing clearances
When I had to change a piston on my original engine in the car when I bought it ('28 block), I checked all the bearings with plastigauge. I can only assume that the engine had been rebuilt earlier with the wrong type of babbitt. The plastigauge was intact and there was a groove in the babbitt where the plastigauge had dented it. Around a year or so later, the engine got a bad knock and had to be towed home. When I pulled the pan down, all the babbitt was in the pan.
After this, Schwalm's got the job of building me a HP engine in a '31 block
__________________
1965 Lotus Elan S2 1930 Model A Sport Coupe |
01-26-2017, 04:52 PM | #11 |
Senior Member
Join Date: Oct 2014
Location: Keystone Heights, FL
Posts: 647
|
Re: Platigage and bearing clearances
S/S, this is what I have in my notes for the Go - No/Go foil method you mentioned:
Use a piece of heavy duty aluminum foil which is .002 thick. The regular is .001 and may be folded if that’s all you have. You want a piece as long as the bearing surface and ½ inch wide. Lay this in the cap along with the shims and tighten it up. Now see if the motor will turn with the foil in place using a 6 inch lever in one of the crank balance holes. Add/remove shims to obtain rotation with .001 and binding with .002.
__________________
I Love Anything That Turns Money Into Noise |
01-26-2017, 06:41 PM | #12 |
Senior Member
Join Date: May 2010
Location: Mpls, MN
Posts: 27,582
|
Re: Platigage and bearing clearances
I use a micrometer to check the crank for egg shape. I've never used plastigauge to check for egg shape journals, but have used it and the foil method to check for oil clearance. Hold the P/G is place with a drop of oil along it's length.
BTW measure the crank at 90* apart to check for egg shape. 180* would be the same as the first measurement. |
01-26-2017, 11:29 PM | #13 | |
Senior Member
Join Date: May 2010
Location: 60615,330th Ave.,Clare, Iowa, 50524
Posts: 1,457
|
Re: Platigage and bearing clearances
Quote:
The reason that Plastigauge indented your Babbitt is because you used the Plastiguage dry. When you do not use the lube, the dry surface will not let the plastigauge slide, or spread out, and so when the Plastigauge has to go some where, so it goes in the Babbitt, instead of spreading out for a true reading. Never read the Babbitt, always read the crank. One thousandths per inch should always be used in setting bearing clearance, that is Minimum. The high side should never be more then a one half thousandths more. If in this case, using a Model "B", a 2 inch crank, when hot, will swell right at .002. So where is your oil clearance? You have none. So what happens when the bearing has to open its self up. It isn't going to be the crank wearing smaller, it is the crank pushing its self free, and the Babbitt is being moved to struggle, and twist its self loose. Model T's have a 1- 1/4 inch crank, when broke in, depending how hard, run with 2 to 3 thousandths clearances. Model A's with a 1- 1/2 rods run about 3 to 3-1/2. Last edited by Kohnke Rebabbitting; 01-28-2017 at 04:54 PM. |
|
01-26-2017, 11:50 PM | #14 |
Senior Member
|
Re: Platigage and bearing clearances
__________________
What's right about America is that although we have a mess of problems, we have great capacity - intellect and resources - to do some thing about them. - Henry Ford II |
01-27-2017, 01:10 AM | #15 |
Senior Member
Join Date: May 2010
Posts: 4,179
|
Re: Platigage and bearing clearances
Hi Bob,
As to "What do you guy think? Never used foil or metal shims in over 59 years, & never used the modern Plastigage Crap introduced by United Kingdom in 1948. My Dad born 1902, Gramps born 1867, Great-Grand-Gramps born 1836 and Great-Great-Grand Gramps with his steam boats, (the Paragon and the Teche), born 1813, & all of us always adjusted bearings successfully without the plastic crap which came out after people lost hand and eye coordination and developed horrible hand writings, developed 5 thumbs, could not "see" level or square , and/or round objects, and could not "feel". If theses same Plastigage dependent guys ever tried to built boats with hand planes & hand saw and planks, they would have all leaked and sunk .... so they had to use Plastigage crap to adjust bearings and later buy aluminum boats or fiberglass boats. Ten years ago on my 1930 Town Sedan, for bearing adjustment , I still used the "feel" method ............ much later recommended by Henry Ford for Model T's in the 1920's in his Model T Ford service Manual. But just one opinion based on Babbitt bearing adjustment perfection from our ancient steam boat engine book written in 1848; <Les Machines a Vapeur>. |
01-27-2017, 11:27 AM | #16 |
Senior Member
Join Date: May 2010
Location: California
Posts: 979
|
Re: Platigage and bearing clearances
H.L.
Would you please explain the "feel" method. I am very interested in learning how to do it. I have to use Plastigage because no one has taught me a better way. Thanks Bob |
01-27-2017, 12:29 PM | #17 |
Senior Member
Join Date: Jun 2010
Location: Temecula, CA
Posts: 4,089
|
Re: Platigage and bearing clearances
I race the Model B engines, and use a little more clearance than for touring. I have gone 153 MPH on a full-babbitt engine, B rods. I'm still running the same block and C crank on the same babbitt mains. I use .0025-.003" clearance and full pressure oiling. Red-line is 6,000 RPM, using a Cook OHV cylinder head. I believe in using Plastigage. To each his own!
Last edited by Jim Brierley; 01-27-2017 at 12:30 PM. Reason: added sentence |
01-27-2017, 01:53 PM | #18 | |
Senior Member
Join Date: May 2010
Location: now Kuna, Idaho
Posts: 3,779
|
Re: Platigage and bearing clearances
Quote:
|
|
01-27-2017, 02:42 PM | #19 |
Senior Member
Join Date: May 2010
Location: Bucks Co, Pa
Posts: 3,740
|
Re: Platigage and bearing clearances
What I believe H.L. is saying is to do (From Experience) what others require measuring devices and methods to accomplish. In other words, I knew a guy who was all surprised when a printer could tell the difference in type sizes (1/77 of an inch IIRC) by sight. Heck! Thats bigger than 1/100th or .010. I' myself could easily feel .002 when I was working in the trade. In some cases .0005. You just sort of know after a while. That's the critical thing, knowing after a while! I doubt if anyone could do it after thirty years as a insurance adjuster. It takes time to develop that feel well enough to rely on. Even now. I wouldn't trust myself doing it (Too many candles on the cake) Stick to micrometers and plastic gauge! Hey, H.L. If I were to replace a Garboard Strake, would I have to pull it out of the water?
Terry |
01-28-2017, 04:06 AM | #20 |
Senior Member
Join Date: May 2010
Posts: 4,179
|
Re: Platigage and bearing clearances
Hi Frank,
Per part of your Reply no. 9., "I know I'm opening a can of worms here. But this is the way it was done in the shops years ago. I learned from an old-timer when I was a teenager." I learned a similar very "simple" method as a teenager 59 years ago by mechanic Dad who was born in 1902. Appears many on this Forum have no clue and even cannot imagine that in 1931 on Ford's no. 20,000,000th car, Babbitt on these cars were later adjusted at least approximately 3 times which would equate to 60 million "successful" Babbitt adjustments made "without" Plastigage. With more Fords after 1931, even more difficult for some to imagine. Maybe Babbitt adjustments by 1931 could have been performed by mechanics and also owners with about a 1931 education level of at least 3rd grade ..... but just guessing ...... I remember riding in my Uncles boat in 1947, powered with a Model B engine with a Police head accompanied by 2 downdraft carburetors ..... no marine transmission .... his particular boat had 2 speeds ..... screaming at wide open & stop ...... absolutely no Plastigage in 1947 ..... he ran it and raced for over 12 years problem free. I could write how this simple method was done years ago, but I can imagine what would happen. Many experienced mechanics on this Forum may wear glasses & hearing aids, but I sincerely doubt if many lose their feelings. Last edited by H. L. Chauvin; 01-28-2017 at 04:30 AM. Reason: typo |
|
|
Sponsored Links (Register now to hide all advertisements) |
|