|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
12-08-2019, 06:22 AM | #1 |
Junior Member
Join Date: Sep 2019
Posts: 9
|
side view mirror
Hi to All,
I would like to install a side view mirror on the passenger side of my 38 pickup. Does anybody know a way to remove the door hinge pin without damaging the body paint? The pin has been painted over. |
12-08-2019, 08:53 AM | #2 |
Senior Member
Join Date: May 2010
Location: East Hartford, Ct
Posts: 5,898
|
Re: side view mirror
You are bound to do some damage to the paint but if you are incapable of driving it out from the bottom with a drift and hammer, you might want to aquire a pin remover from Bob Drake,such as this--
https://www.bobdrake.com/FordItem.aspx?Item=TL-100 You can also watch this on Youtube-- https://www.youtube.com/watch?v=gIWaoA2MaJo
__________________
DON'T RECALL DOING SOMETHING FOR MYSELF BASED ON SOMEONE ELSE'S LIKES OR DISLIKES Last edited by 51 MERC-CT; 12-08-2019 at 08:59 AM. |
Sponsored Links (Register now to hide all advertisements) |
|
12-08-2019, 11:09 AM | #3 |
Senior Member
Join Date: May 2010
Location: Coral Springs FL
Posts: 10,944
|
Re: side view mirror
Raffyjoy, Don't do it. The amount of damage you will do to your paint and door hinge will
make you regret trying to mount a mirror there. Consider a mirror like this: https://www.ebay.com/itm/United-Paci...8AAOSw8S9d3S2D Easy install and easy removal. Please keep us posted. Last edited by 19Fordy; 12-08-2019 at 11:50 AM. |
12-08-2019, 11:39 AM | #4 |
Senior Member
Join Date: Feb 2011
Posts: 794
|
Re: side view mirror
If done carefully there is minimal damage to the top and bottom of the hinge and most of that will be covered by the mirror bracket.
|
12-08-2019, 01:06 PM | #5 |
Senior Member
Join Date: Feb 2011
Location: SUNSHINE MD.
Posts: 318
|
Re: side view mirror
On my 39 pkp. I soak mine with Gibbs pentrating oil , then used my air chisel with the pointed attachment after center punching the bottom of the pin you are only doing the top hinge so it is easy to see what you aredoing .
|
12-08-2019, 01:21 PM | #6 | |
Senior Member
Join Date: May 2010
Location: Minnesota
Posts: 1,826
|
Re: side view mirror
Sponsored Links (Register now to hide all advertisements)
Quote:
|
|
12-08-2019, 04:11 PM | #7 |
Junior Member
Join Date: Sep 2019
Posts: 9
|
Re: side view mirror
Thanks to all for the tips & advise, really appreciate it...will do the penetrating oil and drift/hammer way first, if that fails then i’ll go the Bob Drake route, thanks again....
|
12-08-2019, 05:30 PM | #8 | |
Senior Member
Join Date: Jun 2010
Location: Marana, AZ
Posts: 1,194
|
Re: side view mirror
Quote:
I, too, was afraid to tackle the upper hinge pin!! |
|
12-09-2019, 08:15 AM | #9 |
Senior Member
Join Date: May 2010
Location: Tinley Park Ill
Posts: 1,061
|
Re: side view mirror
19Fordy is correct you cant see anything with a hinge mount mirror on the passenger side
|
12-09-2019, 01:38 PM | #10 |
Member
Join Date: Feb 2011
Posts: 58
|
Re: side view mirror
Not to be contradictory but I have a passenger side mirror on my '39 pickup and it gives a good field of view.
|
12-09-2019, 03:19 PM | #11 |
Senior Member
Join Date: May 2010
Location: Williamsburg, Virginia
Posts: 2,654
|
Re: side view mirror
The mirror that 19 Fordy posted I have on my avatar. When at a show my mirror is bumped into a lot as it extends far away from the car and I can’t tell you manny times I have done it in the garage. Bottom line, they get banged around a lot. On my 32 coupe I switched to 3.5” peep mirrors with stick on convex covers. Great visibility and field of vision. They may not suit your car appearance wise so much if it’s stock but I do like them because they are close in. I also had this setup on my old 40 coupe and loved them. This is all just in my experience .......
|
12-09-2019, 05:11 PM | #12 | |
Senior Member
Join Date: Jul 2011
Location: SF Bay Area
Posts: 6,645
|
Re: side view mirror
Quote:
That's certainly the way to start... And when the penetrating oil does all it can do, and the Drake Hinge Pin Remover bends without budging the pin, then proceed as follows: Carefully file a small flat on top of the pin in order to determine dead center, and center punch for drilling. With a variable speed hand drill, start with a long drill bit of the smallest size you have. The small size is needed so that the next size larger can be directed more accurately toward the center, and the longer bit is to enable you to eyeball a straight shot downward. Use cutting oil, and remove/reinsert the bit often to clear shavings. It won't be necessary to drill all the way through, about 1/3 through is more than enough, as it is only the knurled area at the top of the pin that will offer resistance due to rust penetration. That said, drilling deeper does generate heat, which is beneficial to breaking the rust, and also helps should you need to slightly adjust the path of the drill. Several drill size graduations will bring you close to the diameter of the pin itself, and you will find that the rusted area will then give way to moving the pin upward and out from below. Take care to properly support the door from falling away after the pin removal, as you will be surprised at how easily the pin fairly jumps out of the hinge.
__________________
Alan |
|
12-10-2019, 05:17 PM | #13 |
Senior Member
Join Date: May 2010
Location: Colorado
Posts: 553
|
Re: side view mirror
I used the drive-from-the-bottom method after reading what others did. I was expecting to have a big problem, but they came right out with almost no paint damage. I think it might be best to try that first and try the other suggestions if that doesn't work.
|
|
|
Sponsored Links (Register now to hide all advertisements) |
|