12-08-2020, 06:58 PM | #1 |
Senior Member
Join Date: Sep 2010
Location: Danville, CA
Posts: 1,554
|
turn sigtnals
I got a set of turn signal lights, front and back. I am replacing some that fit into the space between the bumper bars as those are quite low and on my roadster they are hard to see when following me in town. So I hooked them up and did a test, viola, lights blink as requested. Pull out the warning flasher switch and all four flash and two stop lights in the rear also flash. Great. Then back to a right turn signal, blinks for several flashes and seems to slow down the interval and eventually quits blinking. Left turn did the same. Back to the flashers and they are cooperating, blinking away. After a bit the turn signals work again, then seem to get tired and rest a bit. Something needs another ground or some more load? This is a stock, almost, six volt positive ground system, running with a generator and cutout. Any clues? The turn signal set up is the only nonstock stuff in the electrical system. Good battery and no other issues at this point.
|
12-08-2020, 07:24 PM | #2 |
Senior Member
Join Date: May 2010
Location: Tacoma, WA
Posts: 1,025
|
Re: turn sigtnals
MMMm There has been some discussion about led lights. I run the logo lights with 12v with no issues. Sorry I don't have a snappy answer. Is everything ok regarding grounding issues?
|
Sponsored Links (Register now to hide all advertisements) |
|
12-08-2020, 07:38 PM | #3 |
Senior Member
Join Date: May 2010
Location: Concord CA
Posts: 637
|
Re: turn sigtnals
Dave, you need to add load resistors, one on each side to ground. You need more current flowing through the flasher for it to flash at a faster rate. A 6 ohm 20 Watt resistor show work. They will get warm so watch were you mount them. The suppliers sell load resistors.
|
12-08-2020, 07:58 PM | #4 |
Senior Member
Join Date: Jun 2014
Location: Land of Lincoln
Posts: 3,131
|
Re: turn sigtnals
With or without engine running at a fast idle ?
__________________
Don't force it with a little hammer tap, tap, tap get a bigger hammer tap done |
12-08-2020, 08:52 PM | #5 |
Senior Member
Join Date: Sep 2017
Location: Mint Hill, North Carolina
Posts: 386
|
Re: turn sigtnals
Switch to an electronic 6v flasher. They flash at the same rate independent of load
|
12-09-2020, 05:23 AM | #6 | |
Senior Member
Join Date: Sep 2016
Location: Roanoke, VA USA
Posts: 1,908
|
turn sigtnals
Sponsored Links (Register now to hide all advertisements)
Quote:
When I tried that with my LED lights, the electronic flasher worked fine with the engine off, but it went nuts from the static created by the engine when it was running. (I tried multiple electronic flashers with similar results.) I use spark plug straps, rather than shielded spark plug wires, and I think the (unshielded) straps were causing the problem for the electronic 6v flasher for me. I had better luck with a NOS Ideal 535 thermal flasher from eBay. It’s not perfect (for me), but the signal lights do work fairy reliably. (The pilot light on my Signal Stat switch does not work as it should, but at least the signal lights work.) Patrick L seems well versed in signal switches. Sent from my iPhone using Tapatalk |
|
12-09-2020, 07:23 AM | #7 |
Senior Member
Join Date: Jan 2012
Location: Western North Carolina
Posts: 3,897
|
Re: turn sigtnals
Load resistors work for me on my Model A.
I put LED's in my 2016 Chevy pickup. I tried to put an electronic flasher in. I searched for hours to find the flasher by following the clicking sound. Turns out the clicking sound is generated by the computer and played through the speakers. I went with the load resistors for the pickup too.
__________________
A is for apple, green as the sky. Step on the gas, for tomorrow I die. Forget the brakes, they really don't work. The clutch always sticks, and starts with a jerk. My car grows red hair, and flies through the air. Driving's a blast, a blast from the past. |
12-09-2020, 08:23 AM | #8 |
Senior Member
Join Date: May 2010
Location: Largo Florida
Posts: 7,225
|
Re: turn sigtnals
Is your turn switch well grounded ?
It sounds as if you have a flasher issue. Most thermal flashers today are junk. Try an old 535. Fast flashing means more current load is needed. Slow or intermittent flashing usually means a poor ground or bad flasher. |
12-09-2020, 10:21 AM | #9 | |
Senior Member
Join Date: Dec 2017
Location: Guthrie, OK
Posts: 1,145
|
Re: turn sigtnals
Quote:
|
|
12-09-2020, 10:24 AM | #10 | |
Senior Member
Join Date: Dec 2017
Location: Guthrie, OK
Posts: 1,145
|
Re: turn sigtnals
Quote:
|
|
12-09-2020, 12:00 PM | #11 |
Senior Member
Join Date: May 2010
Location: new britain,ct 06052
Posts: 9,390
|
Re: turn sigtnals
Try another flasher.......................
Paul in CT |
12-09-2020, 03:47 PM | #12 |
Senior Member
Join Date: Sep 2010
Location: Danville, CA
Posts: 1,554
|
Re: turn sigtnals
Thanks all. Off to the store for 6 ohm, 20 watt resistor. Will get two and try that. All my parts are old from the 50's, except me, I'm from the 30's. Curious also to see what it does with the engine running. Will try that first.
Dave |
12-09-2020, 03:48 PM | #13 | |
Senior Member
Join Date: Sep 2016
Location: Roanoke, VA USA
Posts: 1,908
|
Re: turn sigtnals
Quote:
Thanks for the response, though. |
|
12-09-2020, 03:49 PM | #14 |
Senior Member
Join Date: Sep 2016
Location: Roanoke, VA USA
Posts: 1,908
|
Re: turn sigtnals
|
12-09-2020, 04:22 PM | #15 |
Senior Member
Join Date: Nov 2010
Location: Anchorage, Alaska
Posts: 9,115
|
Re: turn sigtnals
If you have 12 volts, this flasher is the one that finally worked for me. I have all LEDs, front & back.
__________________
Alaskan A's Antique Auto Mushers of Alaska Model A Ford Club of America Model A Restorers Club Antique Automobile Club of America Mullins Owner's Club |
12-09-2020, 06:26 PM | #16 |
Senior Member
Join Date: May 2010
Location: Washington Cty., ME or Flagler Cty., FL
Posts: 1,106
|
Re: turn sigtnals
I recently purchased a Model A and it had a SignalStat system. It was a mess with wires of all the same color and many disconnected. I removed everything, rewired it with the correct color codes per SgnalStat and purchased a new NAPA 535 Flasher. It works perfectly except for the inside pilot light on the control. I haven't checked it yet but I think the bulb could be 12v and I am running six volts. Ed
|
12-09-2020, 06:50 PM | #17 |
Senior Member
Join Date: May 2010
Location: Southern Upstate New York
Posts: 1,160
|
Re: turn sigtnals
davymc29: Here is the flasher you need for 6 volt positive ground LED turn signals. I have used to flasher for 8 months and it works great. Sorry, the first image on the left is for a negative ground system. Use the information in the photo on the right for a positiveground electronic flasher.
__________________
AL in NY Last edited by AL in NY; 12-09-2020 at 07:07 PM. |
12-10-2020, 05:29 AM | #18 | |
Senior Member
Join Date: Sep 2016
Location: Roanoke, VA USA
Posts: 1,908
|
turn sigtnals
Quote:
That is similar to my experience, except I am sure that I replaced the 12V bulbs with a 6V bulb. That bulb, on rare occasion, actually works when it’s in the right “mood.” Sent from my iPhone using Tapatalk Last edited by shew01; 12-10-2020 at 06:04 PM. |
|
12-10-2020, 09:14 AM | #19 |
Senior Member
Join Date: Jun 2014
Location: Land of Lincoln
Posts: 3,131
|
Re: turn sigtnals
I had an old ford 12 volt generator that the turn signals would work slow or not with the engine not running. I asked a police officer ( sir the signals only work with the engine running and that's when I need the flashers with the engine running please may I start the engine !) Didn't get a ticket for that only the speeding ticket.....27 mph in a 25 mph zone ?
__________________
Don't force it with a little hammer tap, tap, tap get a bigger hammer tap done |
12-10-2020, 10:09 AM | #20 | |
Senior Member
Join Date: Dec 2017
Location: Guthrie, OK
Posts: 1,145
|
Re: turn sigtnals
Quote:
|
|
|
|
Sponsored Links (Register now to hide all advertisements) |
|