|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
01-08-2018, 06:40 AM | #1 |
Senior Member
Join Date: Jun 2015
Location: Signal Mtn, TN (SE TN)
Posts: 2,359
|
Bead blast cabinet
Maybe a bit off topic...
My scat blast cabinet has quit picking up media to the point it is almost disfunctional. Replaced nozzle and parts thereto I understand the siphon tube can be an issue. But also hear there is a upgrade that make it more pressurized. I see nothing on mfg website Any enlightenment appreciated [email protected] |
01-08-2018, 08:05 AM | #2 |
Senior Member
Join Date: Dec 2013
Location: Mossel Bay, about 300km from Cape Town
Posts: 530
|
Re: Bead blast cabinet
Old blu,
I have found the scat or gritt breaks up into smaller pieces over time and obvoiusly the rust and crap from your sandblasting ‘contaminates’ your scatt. I also found small pieces of silicon cloggs the gun. I cleaned the box and poured the scat through a sieve, in quite a strong wind. The sieve caught the debri and the wind blew away the dust. Managed to remove the rust scales and silicon debri and funny enough got the scat nice and shinny again. Also check your air pressure settings. Regards Chris
__________________
Regards Chris Cape Town 28 Model A RPU, 29 Chevy Phaeton, 67 E Type FHC, 67 250SL Pagoda, 83 911 SC |
Sponsored Links (Register now to hide all advertisements) |
|
01-08-2018, 08:37 AM | #3 |
Senior Member
Join Date: Jun 2015
Location: Signal Mtn, TN (SE TN)
Posts: 2,359
|
Re: Bead blast cabinet
Completely cleaned it out and new glass beads, new nozzle.
I did not inspect the siphon tube I hear there is an aftermarket arrangement that adds pressure to the tube Going to call TIP today but nothing on their website |
01-08-2018, 08:55 AM | #4 |
Senior Member
Join Date: May 2010
Location: Eastern Tennessee
Posts: 11,485
|
Re: Bead blast cabinet
This will be interesting Bill because siphon-feeding blast cabinets are SO slow. Pressurized cabinets are SO expensive that I really cannot justify one. I have been looking for a roto-blaster type cabinet, but even those are approaching $10k for a decent sized used one.
I am sure you have already tried this but I would start by process of elimination. Remove the hose attached to the gun and stick your finger over the hole to verify you have strong suction. Then reattach the hose to the gun and move to where the hose attaches to siphon tube and see what you have there. I know that I have already replaced one gun head, and I replace one orifice about every 6 months and I use the carbide tips and still go thru 3 or 4 of those a year. I use TiPs Aluminum Oxide media as I think it cuts faster than the glass beads do. |
01-08-2018, 09:01 AM | #5 |
Senior Member
Join Date: May 2010
Location: Liberty, KY
Posts: 896
|
Re: Bead blast cabinet
My scat blast cabinet did the same thing and it turned out to be a hole worn in the siphon tube by the glass beads where it makes the turn. Hold your hand over the nozzle and hit the foot valve. It will show up the hole.
|
01-08-2018, 09:03 AM | #6 |
Member
Join Date: May 2010
Location: Illinois
Posts: 52
|
Re: Bead blast cabinet
Sponsored Links (Register now to hide all advertisements)
|
01-08-2018, 09:03 AM | #7 |
Member
Join Date: Jan 2012
Location: Riverside NJ
Posts: 48
|
Re: Bead blast cabinet
Old Blu,
Hold the nozzle against an object, sealing it off momentarly, this will back flush the gun and suction tube. It'll be good to go. Oldtguy |
01-08-2018, 09:59 AM | #8 |
Senior Member
Join Date: May 2010
Location: Bismarck ND
Posts: 1,189
|
Re: Bead blast cabinet
I had the siphon tube wear through at the bend where the hose attaches also. Fixed that with a new siphon tube and suction returned great.
|
01-08-2018, 10:16 AM | #9 |
Senior Member
Join Date: May 2010
Location: Lakeville, MN
Posts: 5,159
|
Re: Bead blast cabinet
I to, had a hole develop in the media pickup tube after a lot of blasting in my TP Tool's blast cabinet. The glass beads must really wear on the plastic tubing, especially where there is a bend in the tube. I never though glass beads would cause a hole like other shape edged media would, but they did. Being cheap, I just taped the hole up with electrical tape and so far it is holding. I will soon need to replace the tube with a new one. If your gun looses effectiveness (assuming the pickup tubing isn't clogged), the first thing I would do is inspect the media pickup tubing for a hole.
Rusty Nelson |
01-08-2018, 11:58 AM | #10 |
Senior Member
Join Date: May 2010
Location: Auburn Washington
Posts: 2,550
|
Re: Bead blast cabinet
I to have had to replace three or four times the steel pick up tube, the sand wares a hole on the back side of the bend. speaking of that part, I have my last spare in there now. I will order a couple today.
|
01-08-2018, 12:52 PM | #11 |
Senior Member
Join Date: May 2010
Location: Eastern Tennessee
Posts: 11,485
|
Re: Bead blast cabinet
Because it is the Fordbarn protocol to hi-jack threads ( ), I'm gonna hi-jack Bill's thread a bit and ask, what are y'all using for media in your cabinets??
|
01-08-2018, 01:23 PM | #12 |
Senior Member
Join Date: May 2010
Location: Lakeville, MN
Posts: 5,159
|
Re: Bead blast cabinet
I have used Tractor Supply glass beads in my cabinet. The round container holds 50# I believe. Since I don't use the bead blaster a lot, a 50# container last me 6 months to one year. As everyone knows that uses glass beads, after blasting items for a while the beads turn into a powder. I use a like new Sears 12 gallon wet or dry vacuum with my cabinet. It works very well and only cost me $12 on Craigslist. I have to clean it out about every 3 or 4 months as the filter gets packed with glass bead dust and doesn't work well. I just check the Tractor Supply website and I don't see the glass beads I have purchased in the past. Maybe it isn't on their website.
Rusty Nelson |
01-08-2018, 02:03 PM | #13 |
Senior Member
Join Date: Jun 2015
Location: Signal Mtn, TN (SE TN)
Posts: 2,359
|
Re: Bead blast cabinet
Since I'm going rabbit trails too. The shop vac...I've seen where a 5 gallon bucket put in line with the vac with water in the base used to trap a lot of particles. Once I get the blaster back working, I'm going to try that. I saw a sheet rock guy with the exact set up catching sheet rock dust. He had to change the water daily or more.
|
01-08-2018, 02:17 PM | #14 |
Senior Member
Join Date: May 2010
Location: Lakeville, MN
Posts: 5,159
|
Re: Bead blast cabinet
Oldbluoval,
When you get your water bucket setup done, please take some pictures of it and post them here. My problem is my shop is mostly unheated and here in MN it gets real cold and the water would freeze and probably split the bucket. But in the spring, summer and fall the water bucket setup seems like it would prolong the time to clean out the vacuum filter. Rusty Nelson |
01-08-2018, 08:14 PM | #15 |
Senior Member
Join Date: May 2010
Location: Bismarck ND
Posts: 1,189
|
Re: Bead blast cabinet
I am using glass beads. A friend works for a highway contractor and they use glass beads to make the center stripe on the highway reflective. They had a huge tote that got rained on and I got it for free. I laid it out on tarps in the sum and dried it. I got 2 55gal drums full of dry beads. They are slightly smaller than beads used for blasting, but they work great. I have a lifetime supply.
|
Thread Tools | |
Display Modes | |
|
|
Sponsored Links (Register now to hide all advertisements) |
|