Go Back   The Ford Barn > General Discussion > Model A (1928-31)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 09-23-2021, 03:04 PM   #1
griffin
Junior Member
 
Join Date: Oct 2010
Location: North of Houston, Tex.
Posts: 27
Default Champion 3x electrode

Looking at my 1st set of 3x plugs, it appears the side electrode points to the side of the center electrode, not hover over the top as most other plugs do.

Am I correct or am I looking at plugs somebody has gotten their mileage out of? Another issue that appears to me is the corrosion on the body of the plug. I have no idea the age of these plugs. These are flat-top 3 plugs.

My plugs are gapped at .045, which is obviously waaaayy too much.

I'm not going to reuse these plugs, just curious how the electrodes are supposed to be positioned.
Attached Images
File Type: jpg 20210923_144342.jpg (28.1 KB, 564 views)

Last edited by griffin; 09-24-2021 at 11:58 AM.
griffin is offline   Reply With Quote
Old 09-23-2021, 03:35 PM   #2
Werner
Senior Member
 
Werner's Avatar
 
Join Date: Jan 2019
Location: Germany, near Aachen
Posts: 1,151
Default Re: Champion 3x electrode

Griffin,

this is an ancient spark plug like the one used in the past. Collectible. Nowadays the ground electrode sits above the middle electrode.


btw.: Modern iridium spark plugs are recommended.
__________________
Beste Gruesse aus Deutschland,
Werner


Ford Model A, Roadster, 1928
Citroen 11 CV, 1947
Hercules W 2000, 1976; (with NSU-Wankel Rotary Engine), Canadian version
Werner is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 09-23-2021, 04:43 PM   #3
AL in NY
Senior Member
 
AL in NY's Avatar
 
Join Date: May 2010
Location: Southern Upstate New York
Posts: 1,147
Default Re: Champion 3x electrode

The 3X plugs are the best plugs (IMHO) for the Model A. They can be gapped on the side of the electrode with no performance problems. Remember, this is a very low compression, low HP engine.
__________________
AL in NY
AL in NY is offline   Reply With Quote
Old 09-23-2021, 05:18 PM   #4
woofa.express
Senior Member
 
woofa.express's Avatar
 
Join Date: Jan 2018
Location: Tocumwal, NSW, Australia
Posts: 1,741
Default Re: Champion 3x electrode

This is perhaps some worthless information for you Al.
I remember the negative electrodes on early aviation sparkplugs. Like one in the picture below but two opposing platinum wires. The second picture is a modern aviation spark plug using plug electrodes which is probably the only type available on today’s market. pictures from the internet.
Attached Images
File Type: jpg Screen Shot 2021-09-24 at 08.08.33.jpg (10.8 KB, 75 views)
File Type: jpg Screen Shot 2021-09-24 at 08.08.59.jpg (9.9 KB, 82 views)
__________________
I know many things,
But I don't know everything,
Sometimes I forget things.

And there are times when I have a long memory.
woofa.express is offline   Reply With Quote
Old 09-23-2021, 07:20 PM   #5
mercman from oz
Senior Member
 
mercman from oz's Avatar
 
Join Date: May 2012
Location: Queensland, Australia
Posts: 10,266
Default Re: Champion 3x electrode


I think that it needs replacing?
mercman from oz is offline   Reply With Quote
Old 09-23-2021, 07:33 PM   #6
nkaminar
Senior Member
 
nkaminar's Avatar
 
Join Date: Jan 2012
Location: Western North Carolina
Posts: 3,775
Default Re: Champion 3x electrode

Sponsored Links (Register now to hide all advertisements)
The plugs were made that way so that any oil or liquid gasoline (remember that gasoline was at one time close to kerosene) would drip off the electrodes to clear them.

Years ago there was a machine that was used to sandblast plugs to clean them up. You may try that on these plugs. You can just use a blast cabinet.
__________________
A is for apple, green as the sky.
Step on the gas, for tomorrow I die.
Forget the brakes, they really don't work.
The clutch always sticks, and starts with a jerk.
My car grows red hair, and flies through the air.
Driving's a blast, a blast from the past.
nkaminar is offline   Reply With Quote
Old 09-23-2021, 11:45 PM   #7
J Franklin
Senior Member
 
J Franklin's Avatar
 
Join Date: May 2010
Location: Oregon
Posts: 5,941
Default Re: Champion 3x electrode

Quote:
Originally Posted by mercman from oz View Post

I think that it needs replacing?
Those too young won't remember rebuilt spark plugs, with new electrodes welded on to replace the worn ones. Things were rebuilt in the golden years. Maybe those still have some life.
J Franklin is offline   Reply With Quote
Old 09-24-2021, 10:38 AM   #8
katy
Senior Member
 
katy's Avatar
 
Join Date: Jun 2015
Location: Red Deer, Alberta
Posts: 4,992
Default Re: Champion 3x electrode

Just set the gap at .035", put them back in and go.
__________________
If you don't hear a rumor by 10 AM, start one!.
Got my education out behind the barn!
katy is offline   Reply With Quote
Old 09-24-2021, 01:10 PM   #9
Werner
Senior Member
 
Werner's Avatar
 
Join Date: Jan 2019
Location: Germany, near Aachen
Posts: 1,151
Default Re: Champion 3x electrode

Quote:
Originally Posted by J Franklin View Post
Those too young won't remember rebuilt spark plugs, with new electrodes welded on to replace the worn ones. Things were rebuilt in the golden years. Maybe those still have some life.
I thought such little things were only repaired in the poor times in Germany.



Here are some interesting things from my old spark plug collection. There were also spark plugs that could be dismantled, new seals and a new insulated center electrode were put in.

Repaired spark plugs were embossed and stamped with "Repariert" and the name of the repair company
Attached Images
File Type: jpg P1120268.JPG (55.5 KB, 55 views)
File Type: jpg P1120263.JPG (172.5 KB, 47 views)
__________________
Beste Gruesse aus Deutschland,
Werner


Ford Model A, Roadster, 1928
Citroen 11 CV, 1947
Hercules W 2000, 1976; (with NSU-Wankel Rotary Engine), Canadian version
Werner is offline   Reply With Quote
Old 09-24-2021, 03:13 PM   #10
Kurt in NJ
Senior Member
 
Kurt in NJ's Avatar
 
Join Date: May 2010
Location: on the Littlefield
Posts: 6,132
Default Re: Champion 3x electrode

One of the ways to change the gap is to loosen the nut holding the ceramic and rotate to less worn area of center electrode
Kurt in NJ is offline   Reply With Quote
Old 09-24-2021, 04:33 PM   #11
Gene F
Senior Member
 
Gene F's Avatar
 
Join Date: Mar 2012
Location: Ohio
Posts: 1,890
Default Re: Champion 3x electrode

Anyone ever use those E-3 spark plugs before?
Gene F is offline   Reply With Quote
Old 09-24-2021, 05:31 PM   #12
woofa.express
Senior Member
 
woofa.express's Avatar
 
Join Date: Jan 2018
Location: Tocumwal, NSW, Australia
Posts: 1,741
Default Re: Champion 3x electrode

Some more worthless information for you.
It doesn’t seem so long ago, but probably 30 years, when aviation fuel (avgas) had a lead component. At a 100hly service it was necessary to remove lead in the upper reach of the ceramic insulating cylinder. One could purchase a special cleaning tool but I used to use a disused hacksaw blade which I had ground down on a bench grinder to a blunt point with a reach of about 1 and quarter inch. This was followed by a clean on a spark plug cleaner. I didn’t put platinum electrode plugs on a cleaner.
__________________
I know many things,
But I don't know everything,
Sometimes I forget things.

And there are times when I have a long memory.

Last edited by woofa.express; 09-24-2021 at 07:01 PM.
woofa.express is offline   Reply With Quote
Old 09-24-2021, 05:42 PM   #13
Utopia Texas
Senior Member
 
Utopia Texas's Avatar
 
Join Date: Apr 2016
Location: Brookshire & Cat Spring,Texas
Posts: 222
Default Re: Champion 3x electrode

Snyder’s sells a replacement base for the 3X.

Utopia Texas is offline   Reply With Quote
Old 09-24-2021, 11:26 PM   #14
1930artdeco
Senior Member
 
1930artdeco's Avatar
 
Join Date: May 2010
Location: Lynden, Wa
Posts: 3,548
Default Re: Champion 3x electrode

How does one rebuild the 3X plugs? I have a set that were acting up so I want to clean and rebuild them. Where does one get new seals for them?

Thanks,

Mike
__________________
1930 TownSedan (Briggs)
1957 Country Sedan
1930artdeco is offline   Reply With Quote
Old 09-25-2021, 01:55 PM   #15
Brad in Germany
Senior Member
 
Brad in Germany's Avatar
 
Join Date: May 2010
Location: Potomac, Maryland
Posts: 908
Default Re: Champion 3x electrode

Quote:
Originally Posted by Werner View Post
I thought such little things were only repaired in the poor times in Germany.

Here are some interesting things from my old spark plug collection. There were also spark plugs that could be dismantled, new seals and a new insulated center electrode were put in.

Repaired spark plugs were embossed and stamped with "Repariert" and the name of the repair company
Hi Werner,

FWIW, according to era Bosch documents, the original spark plugs for German assembled Model A's for 1928-1930 are the BOSCH DZ 20/3 (detachable) or BOSCH Z 20/3 (non-detachable).


For 1931 (and newer), according to era Ford and Bosch documents, original spark plugs for German built Model A's are the BOSCH DZ 45/1 (detachable) or the BOSCH Z 45/1 (non-detachable).


Brad in Maryland
Attached Images
File Type: jpeg fullsizeoutput_283e.jpeg (74.2 KB, 329 views)
File Type: jpg fullsizeoutput_3a9e.jpg (18.6 KB, 323 views)
File Type: jpg fullsizeoutput_3aa1.jpg (25.1 KB, 327 views)
Brad in Germany is offline   Reply With Quote
Old 09-25-2021, 04:10 PM   #16
Werner
Senior Member
 
Werner's Avatar
 
Join Date: Jan 2019
Location: Germany, near Aachen
Posts: 1,151
Default Re: Champion 3x electrode

Guten Abend Brad,


thanks for nice informations! It's looking good.
__________________
Beste Gruesse aus Deutschland,
Werner


Ford Model A, Roadster, 1928
Citroen 11 CV, 1947
Hercules W 2000, 1976; (with NSU-Wankel Rotary Engine), Canadian version
Werner is offline   Reply With Quote
Old 12-06-2021, 10:21 PM   #17
PinoleMike
Junior Member
 
Join Date: Nov 2021
Posts: 7
Default Re: Champion 3x electrode

I have the same plugs in my 1929 Town Sedan. They were in it when I purchased it 8 years ago. This thread has answered many of my questions. Thanks guys!
PinoleMike is offline   Reply With Quote
Old 12-06-2021, 11:37 PM   #18
Gary WA
Senior Member
 
Gary WA's Avatar
 
Join Date: May 2010
Location: Clinton,WA/Whidbey Island
Posts: 4,085
Default Re: Champion 3x electrode

Quote:
Originally Posted by 1930artdeco View Post
How does one rebuild the 3X plugs? I have a set that were acting up so I want to clean and rebuild them. Where does one get new seals for them?

Thanks,

Mike
Take them apart and clean them,Bead blast base interior only, not ceramic part. There is a very thin washer between ceramic and base,!http://modelabasics.com/3xplug.htm seals only one are usually good .
__________________
www.whidbeymodelaclub.com
Gary WA is offline   Reply With Quote
Old 12-06-2021, 11:49 PM   #19
J Franklin
Senior Member
 
J Franklin's Avatar
 
Join Date: May 2010
Location: Oregon
Posts: 5,941
Default Re: Champion 3x electrode

Quote:
Originally Posted by 1930artdeco View Post
How does one rebuild the 3X plugs? I have a set that were acting up so I want to clean and rebuild them. Where does one get new seals for them?

Thanks,

Mike
I ran accross this post with good info.

https://modeltfordfix.com/cleaning-t...rk-plug-t1386/
J Franklin is offline   Reply With Quote
Old 12-07-2021, 10:55 AM   #20
katy
Senior Member
 
katy's Avatar
 
Join Date: Jun 2015
Location: Red Deer, Alberta
Posts: 4,992
Default Re: Champion 3x electrode

Quote:
Originally Posted by PinoleMike View Post
I have the same plugs in my 1929 Town Sedan. They were in it when I purchased it 8 years ago.
Does it get driven much?
__________________
If you don't hear a rumor by 10 AM, start one!.
Got my education out behind the barn!
katy is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 06:33 AM.