Go Back   The Ford Barn > General Discussion > Model A (1928-31)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 09-24-2021, 12:00 PM   #1
Russell Reay
Senior Member
 
Join Date: May 2021
Location: NH/ VT
Posts: 329
Default Torque wrench

This isn't specific to Model As, but that is the challenge du jour. I just replaced an axle shaft, and need to reassemble the carrier. Fortunately I was able to punch the corresponding halves to be sure they went back together correctly, and was able to hold the spider gears in place so they are all back where they belong. The book says to torque the carrier nuts to 30-35 lbs. I have a torque wrench--probably from NAPA- that I haven't used for 15 yrs. It is the type with a knurled handled which you turn to the desired setting, then lock in place with a knob at the bottom. When the setting is reached the handle snaps--very easy to use. However, the nuts never get tight enough to trip the wrench. I set a nut and bolt into the frame of my A to use as a test site, and the wrench trips every time at a modest pressure-35 lbs seems realistic. Having no luck with my wrench, I borrowed a neighbor's. His is the same design, made by Tekton, but my experience is almost the same. In tightening the carrier nuts, I think they are way too tight before tripping the wrench. I was able to trip two, did not dare tighten others any more, then stripped the threads on one before it tripped. Fortunately I have another carrier I can rob nuts and bolts from. Do they still make the torque wrenches with a needle pointer ? What's the problem?
Russell Reay is offline   Reply With Quote
Old 09-24-2021, 12:26 PM   #2
Ivan in southeast va.
Senior Member
 
Ivan in southeast va.'s Avatar
 
Join Date: Oct 2012
Location: Portsmouth, Virginia
Posts: 303
Default Re: Torque wrench

At this point I would set the torque wrench aside and just snug them up real good without over tightening. Sometimes you just have to go by feel.
Ivan in southeast va. is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 09-24-2021, 12:32 PM   #3
Patrick L.
Senior Member
 
Patrick L.'s Avatar
 
Join Date: May 2010
Location: Largo Florida
Posts: 7,225
Default Re: Torque wrench

I agree with Ivan.

If a torque has been sitting around for quite awhile, especially if it hasn't been backed off, it'll need to be exercised quite a but before it'll work right.
Patrick L. is offline   Reply With Quote
Old 09-24-2021, 12:36 PM   #4
Russell Reay
Senior Member
 
Join Date: May 2021
Location: NH/ VT
Posts: 329
Default Re: Torque wrench

Thanks, guys. Mine was stored w/o being backed off, but the neighbor's was backed off all the way. Except for head bolts, I feel more confident with the 'feel' method.
Russell Reay is offline   Reply With Quote
Old 09-24-2021, 12:43 PM   #5
Werner
Senior Member
 
Werner's Avatar
 
Join Date: Jan 2019
Location: Germany, near Aachen
Posts: 1,151
Default Re: Torque wrench

Russel,

the instruction manual for my high-quality 'Hazet' torque wrench says:

"It must always be stored relaxed. After a long period of non-use, it should be set to the highest level and operated 20 - 30 times in a row until it is triggered."
__________________
Beste Gruesse aus Deutschland,
Werner


Ford Model A, Roadster, 1928
Citroen 11 CV, 1947
Hercules W 2000, 1976; (with NSU-Wankel Rotary Engine), Canadian version
Werner is offline   Reply With Quote
Old 09-24-2021, 03:56 PM   #6
Kurt in NJ
Senior Member
 
Kurt in NJ's Avatar
 
Join Date: May 2010
Location: on the Littlefield
Posts: 6,132
Default Re: Torque wrench

Sponsored Links (Register now to hide all advertisements)
Surprisingly the harbor freight torque wrenches I tested on the snap on truck were all dead on at several different torque settings
Kurt in NJ is offline   Reply With Quote
Old 09-25-2021, 12:38 PM   #7
katy
Senior Member
 
katy's Avatar
 
Join Date: Jun 2015
Location: Red Deer, Alberta
Posts: 4,992
Default Re: Torque wrench

Get new grade 8 bolts and nuts and start over.
__________________
If you don't hear a rumor by 10 AM, start one!.
Got my education out behind the barn!
katy is offline   Reply With Quote
Old 09-25-2021, 01:22 PM   #8
Dean Lemoine
Senior Member
 
Dean Lemoine's Avatar
 
Join Date: Nov 2018
Location: Dahlonega, Ga
Posts: 251
Default Re: Torque wrench

There are several ways to easily calibrate a torque wrench. Do a search and take your pick. I use a hand held luggage scale, it literally only takes a minute
Dean Lemoine is offline   Reply With Quote
Old 09-25-2021, 01:33 PM   #9
nkaminar
Senior Member
 
nkaminar's Avatar
 
Join Date: Jan 2012
Location: Western North Carolina
Posts: 3,772
Default Re: Torque wrench

Except for large fasteners, mechanics have a good feel for the correct torque.

At a given torque, the stress on the bolt or stud varies depends on whether the nut has been lubricated and what kind of lubrication was used.
__________________
A is for apple, green as the sky.
Step on the gas, for tomorrow I die.
Forget the brakes, they really don't work.
The clutch always sticks, and starts with a jerk.
My car grows red hair, and flies through the air.
Driving's a blast, a blast from the past.
nkaminar is offline   Reply With Quote
Old 09-25-2021, 03:25 PM   #10
Crankster
Senior Member
 
Crankster's Avatar
 
Join Date: Oct 2017
Posts: 563
Default Re: Torque wrench

There is no technical reason why a torque wrench would not achieve the correct clamping force in any particular task (unless the wrench is out of calibration or, maybe there's a typo in the specifications).
Crankster is offline   Reply With Quote
Old 09-25-2021, 03:55 PM   #11
40 Deluxe
Senior Member
 
Join Date: May 2010
Location: now Kuna, Idaho
Posts: 3,773
Default Re: Torque wrench

Maybe a few drops of oil on the head would help after sitting so long.
40 Deluxe is online now   Reply With Quote
Old 09-25-2021, 04:25 PM   #12
Ruth
Senior Member
 
Join Date: May 2016
Location: Glide, Oregon
Posts: 1,329
Default Re: Torque wrench

Quote:
Originally Posted by Kurt in NJ View Post
Surprisingly the harbor freight torque wrenches I tested on the snap on truck were all dead on at several different torque settings
There was a comparison test in a magazine (I think it was Hot Rod) a few years ago that said the Harbor Freight torque Wrench to be one of the more accurate ones tested.
__________________
Ruth
"Sometimes you really DO need to read the whole thread"

Last edited by Ruth; 09-25-2021 at 04:32 PM.
Ruth is offline   Reply With Quote
Old 09-25-2021, 08:11 PM   #13
Ray in La Mesa
Senior Member
 
Join Date: May 2010
Location: La Mesa Ca
Posts: 1,152
Default Re: Torque wrench

I've had a Sears craftsman torque wrench for 50 years and it started to vary in settings so I went on line and found an article on how to disassemble it, clean it, lube it & put it back together. To reset it, the end of the handle had solder in it, melted that out to access the adjustment knob. Then compared it with 5 other torque wrenches had access to and adjusted accordingly, now it works great, in fact the click feature is very quiet & subtle .
Ray in La Mesa is offline   Reply With Quote
Old 09-27-2021, 12:23 PM   #14
redmodelt
Senior Member
 
redmodelt's Avatar
 
Join Date: May 2010
Location: Portland OR
Posts: 6,339
Default Re: Torque wrench

I would say dry or lubed threads come into play. If the threads are lubed, it will take longer to reach the 30-35 foot pound reading, which could result in pulled thread. Charts show 2 readings for each type bolt/nut, dry or lubed. You might try a beam type torque wrench and see if that helps. At this point, would look at the thread on both the nut and bolt to see if they are pulled. Often in the past they may have been over tightened so now you are working with compromised thread, which is not allowing the correct torque.
__________________
I know the voices aren't real but damn they have some good ideas!
redmodelt is offline   Reply With Quote
Old 09-27-2021, 01:18 PM   #15
Patrick L.
Senior Member
 
Patrick L.'s Avatar
 
Join Date: May 2010
Location: Largo Florida
Posts: 7,225
Default Re: Torque wrench

Torque beam type torque wrenches can still be found. I'm not sure if they can be found new. Mine are quite old and I like them.
Patrick L. is offline   Reply With Quote
Old 09-28-2021, 08:23 PM   #16
katy
Senior Member
 
katy's Avatar
 
Join Date: Jun 2015
Location: Red Deer, Alberta
Posts: 4,992
Default Re: Torque wrench

Quote:
Originally Posted by Patrick L. View Post
Torque beam type torque wrenches can still be found. I'm not sure if they can be found new.
There's lots of new ones available, 1/4" 3/8" and 1/2" drive.
I recently picked up an old 3/4" drive one at restore.
__________________
If you don't hear a rumor by 10 AM, start one!.
Got my education out behind the barn!
katy is offline   Reply With Quote
Old 09-28-2021, 09:59 PM   #17
Russell Reay
Senior Member
 
Join Date: May 2021
Location: NH/ VT
Posts: 329
Default Re: Torque wrench

Quote:
Originally Posted by Patrick L. View Post
Torque beam type torque wrenches can still be found. I'm not sure if they can be found new. Mine are quite old and I like them.
I just ordered a 1/2" drive. After this experience I don't dare trust the adjustables.
Russell Reay is offline   Reply With Quote
Old 09-30-2021, 10:01 AM   #18
katy
Senior Member
 
katy's Avatar
 
Join Date: Jun 2015
Location: Red Deer, Alberta
Posts: 4,992
Default Re: Torque wrench

Quote:
Originally Posted by Russell Reay View Post
After this experience I don't dare trust the adjustables.
I've been using the same Proto click type 1/2" drive since around 1960, always stored relaxed, never any problems w/it. I test it w/a beam type every few years and it's always bang on.
__________________
If you don't hear a rumor by 10 AM, start one!.
Got my education out behind the barn!
katy is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 09:34 PM.