39 sedan front disc brake or not?

[funrunr]

Originally Posted by Tinker

Makes sense, since the drop axle will put the wheels in some. Are you running wide fives on your 40?

No 5 on 5½, If it would help I could measure my distance to the fender from the tire and someone with drums could compare with their stock set up

[dude]

Originally Posted by HCO41

While I agree with those who properly maintain the original brakes whether mechanical or hydraulic, I see no reason why someone should be referred to the HAMB just because they want to do discs!
If Alan feels so strongly about this thread then I suggest that he make up a list of modifications he would approve so we can avoid his references.
For example, I have '39 brakes on my '37, should I go to the H.A.M.B.?
I plan to replace my 60hp with an 8ba and, god forbid, I'm going to use a "78" case with later gears! Go to the H.A.M.B.?
Many people are adding a dual master cylinder, for safety, should they go to the H.A.M.B.?
How about multiple carburetors, four barrels, electric fuel pumps, non-stock cams, longer strokes, T-5 5 speed transmissions and so many more "hot rod" modifications? To the H.A.M.B.?
I think that as long as the flathead engine is the power, no matter the application, this forum can be enjoyed by all of us.
Howard

"Bingo" open minded man.....

[Robert Dip]

Right on klicker....I have stock brakes on my '39 coupe....highly modified 59AB, L-Z 25T gears, and I DRIVE. With the bias ply tires, I can easily lock up the front tires...so, what's the point. 400 HP....a/t trans...wide radials....driving like your hauling moonshine escaping the cops.....OK....get discs. Never had discs on my cars, been at it for 50 years....never needed them....but, that's me. Robert

[bgarrett]

Originally Posted by ford38v8

Try the Hamb. This forum doesn't do street rods.

The HAMB doesnt do streetrods either. Its for traditional hotrods

[V8COOPMAN]

bgarrett is absolutely correct! The HAMB has absolutely no desire to be associated with "street rods". Huge difference between a street rod and a hot rod. DD

[mrtexas]

Sponsored Links (Register now to hide all advertisements)

Originally Posted by V8COOPMAN

bgarrett is absolutely correct! The HAMB has absolutely no desire to be associated with "street rods". Huge difference between a street rod and a hot rod. DD

You are correct. My post about throttle body FI on my 37 flathead was deleted.

[rheltzel]

My '35 has '39 juice brakes in good working order. I enjoy driving just a bit more carefully when driving it. I go with the speed of traffic, but allow a bit more room between me and car in front of me. For that, the "stock" brakes are just fine. I like the fact that I have to pay attention and plan ahead. In fact, it gives me time to see what a-holes most drivers in their "moderns" are, always darting in and out of traffic, tailgating, and driving too fast for surrounding conditions.

If I want to drive fast, I drive my S-2000. In it, I can out-stop almost every car on the road. I can make unlimited panic stops from 70 mph with no fade in less than a quarter the distance required by my '35. I can drive at extra-legal and/or extra-sensible speeds on any road, in any condition, without giving a thought to whether my brakes are up to the task.

If I had to give up one to keep the other, I'd give up the S-2000 in a minute.

If I tried and somehow was successful in modifying my '35 to stop as well as my S-2000, it wouldn't be the same car. Not worse, if that's what you want, but different.

But that's just me...

[Aquaroscoe]

On the ECI 1940 setup, the hubs are kicked out about 1/2" on each side.