|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
11-30-2021, 09:57 PM | #1 |
Senior Member
Join Date: May 2010
Posts: 2,480
|
'32 reinforcing plate 4 slotted frame holes steering
Hi; I have a late '32 frame with slotted frame holes and need the reinforcing plate- have a chrome one tho. Are these available or shall I have 10 made for you all? Will fit 33/34 also. Newc
|
11-30-2021, 10:13 PM | #2 |
Senior Member
Join Date: May 2010
Posts: 4,460
|
Re: '32 reinforcing plate 4 slotted frame holes steering
I think the slotted hole steering holes were so the same frame could be used on the passenger car and pickup. As for the plate, try Neal Jennings. I got one from him earlier this year.
|
Sponsored Links (Register now to hide all advertisements) |
|
11-30-2021, 11:02 PM | #3 |
Senior Member
Join Date: Jan 2011
Location: sw minnesota
Posts: 4,567
|
Re: '32 reinforcing plate 4 slotted frame holes steering
The frame holes are slotted, but the plate is not supposed to be. They are often missing, and you can see the damage done to a frame without them. Not too hard to make, but someone should repo them I would think
|
11-30-2021, 11:04 PM | #4 |
Senior Member
Join Date: May 2015
Posts: 8,074
|
Re: '32 reinforcing plate 4 slotted frame holes steering
__________________
The only thing nice about being imperfect is the joy it brings to others.... "Silver rings, your butt! Them's washers!" "We shot our way out of that town for a dollar's worth of steel holes!" - from 'The Wild Bunch' - 1969 https://www.youtube.com/watch?v=7NReUd2_0u0 |
11-30-2021, 11:11 PM | #5 |
Senior Member
Join Date: May 2010
Location: southeastern Michigan
Posts: 10,093
|
Re: '32 reinforcing plate 4 slotted frame holes steering
Dale,
I'd like a couple for my '33s, please, if you proceed to make them. While late '32 frames had slotted holes to eliminate the need for separate steering sector housings for commercial vehicles as Krylon32 indicates, that plate did not come into use until late in the '33 model year. They are a good idea, however, as castle or slotted hex nuts do a number on the paint on the frame when slotted holes are present. |
12-01-2021, 07:40 AM | #6 |
Senior Member
Join Date: Mar 2014
Location: Jacksonville FL
Posts: 3,946
|
Re: '32 reinforcing plate 4 slotted frame holes steering
Sponsored Links (Register now to hide all advertisements)
|
12-01-2021, 07:48 AM | #7 |
Senior Member
Join Date: Jun 2010
Location: St Croix Falls WI
Posts: 2,080
|
Re: '32 reinforcing plate 4 slotted frame holes steering
And 2 here also ,
|
12-01-2021, 09:20 AM | #8 |
Senior Member
Join Date: May 2010
Location: Montgomery, NY & Port St. Lucie Florida
Posts: 935
|
Re: '32 reinforcing plate 4 slotted frame holes steering
Maybe you want to make 20?
I'm in for 2 or 3 soooo
__________________
Early Ford Lock & Key Service http://www.fordbarn.com/forum/showthread.php?t=46583 |
12-01-2021, 09:23 AM | #9 |
Senior Member
Join Date: May 2010
Posts: 4,460
|
Re: '32 reinforcing plate 4 slotted frame holes steering
As I said above I got mine from Neal Jennings. He's NealinCA on here and specializes in early steering and parts.
|
12-01-2021, 09:46 AM | #10 |
Senior Member
Join Date: May 2010
Location: Coral Springs FL
Posts: 10,919
|
Re: '32 reinforcing plate 4 slotted frame holes steering
Have them water jet cut for a nice clean edge.
|
12-01-2021, 11:23 AM | #11 |
Senior Member
Join Date: Jun 2012
Location: Long Island,NY
Posts: 1,554
|
Re: '32 reinforcing plate 4 slotted frame holes steering
Make more than you anticipate selling. I'll give you and example. I started reproducing '41 thru '48 Station Wagon, tailgate hangers. I tooled up and made six and kept on receiving orders and the final tally was 41 set's sold.
|
12-01-2021, 09:40 PM | #12 | |
Senior Member
Join Date: May 2010
Location: Central Coast, Calif.
Posts: 839
|
Re: '32 reinforcing plate 4 slotted frame holes steering
Quote:
See pics below, comparing my version to an original 34 plate. If interested in one please send me a PM. Thanks, Neal |
|
12-01-2021, 10:34 PM | #13 |
Senior Member
Join Date: Jan 2011
Location: sw minnesota
Posts: 4,567
|
Re: '32 reinforcing plate 4 slotted frame holes steering
Nice job Neal, as usual !
|
Thread Tools | |
Display Modes | |
|
|
Sponsored Links (Register now to hide all advertisements) |
|