Go Back   The Ford Barn > General Discussion > Early V8 (1932-53)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 01-02-2019, 04:53 PM   #1
[email protected]
Senior Member
 
Join Date: Nov 2015
Location: Sharon, Conn.
Posts: 112
Default Petronix ignition question

Something came up today that you might find interesting. Apparently Petronix is now requesting that you use carbon track secondary wires with their Petronix conversion on 12 volt systems. I have a Petronix ignition on my 48 ford F-1 which I converted to 12 volts several years ago. I still use the copper core wires and have never had a problem. Petronix says that some failures of their system have been traced back to the use of copper versus carbon track spark plug (secondary) wires.

Has anyone had a problem or have anything to add to this?

Thanks!

Bill on Conn.
patbill@megahits.com is offline   Reply With Quote
Old 01-02-2019, 05:06 PM   #2
JSeery
Member Emeritus
 
JSeery's Avatar
 
Join Date: Nov 2012
Location: Wichita KS
Posts: 16,132
Default Re: Petronix ignition question

I didn't think this was anything new, I have heard this for at least several years.
JSeery is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 01-02-2019, 05:43 PM   #3
51 MERC-CT
Senior Member
 
51 MERC-CT's Avatar
 
Join Date: May 2010
Location: East Hartford, Ct
Posts: 5,898
Default Re: Petronix ignition question

Nothing new, I have been running Pertronix 12 volt conversion for well over 10 years and seem to recall that it was a recommendation back then just as this one is as provided with Mallory Unilite conversions.
You may well get away with what you are running but if you experience problems it may be time to revisit the ignition wire recommendation.
Attached Images
File Type: jpg PERT-MALL.JPG (53.0 KB, 315 views)
__________________
DON'T RECALL DOING SOMETHING FOR MYSELF BASED ON SOMEONE ELSE'S LIKES OR DISLIKES

Last edited by 51 MERC-CT; 01-03-2019 at 09:45 AM.
51 MERC-CT is offline   Reply With Quote
Old 01-02-2019, 07:37 PM   #4
Jack E/NJ
Senior Member
 
Jack E/NJ's Avatar
 
Join Date: May 2010
Posts: 2,171
Default Re: Petronix ignition question

Nothing like a good set of points, condenser & run resistor to solve all your 6 & 12 volt ignition woes. 8^) Jack E?NJ
Jack E/NJ is offline   Reply With Quote
Old 01-02-2019, 10:48 PM   #5
Ronnieroadster
Senior Member
 
Ronnieroadster's Avatar
 
Join Date: Dec 2010
Location: East Coast in CT
Posts: 1,509
Default Re: Petronix ignition question

Hard to beat the Pertronix conversions its simply a copy of the Ford and Chrysler ignition systems form the seventy's which were extremely reliable. I believe its called a hall effect switch triggered by magnets and some by a metal edge crossing the face of the module a very simple system with no wearing parts. Its always been a requirement listed in the instructions to use suppression ignition wires another important consideration is the proper coil used the instructions list the ohm rating needed. Using the copper core wires will work BUT in time that may not be the case. Using the correct wires will show an improvement in performance at least thats what I have experienced when working on similar installations like yours installed by others using the parts listed as do not use.
Ronnieroadster
__________________
I use the F word a lot no not that word these words Flathead , Focus and Finish.
"Life Member of the Bonneville 200 MPH Club using a Ford Flathead block"
Owner , Builder, Driver of the First Ford Flathead bodied roadster to run 200 MPH Record July 13, 2018 LTA timing association 200.921 in one and a half miles burning gasoline.
First ever gas burning Ford flathead powered roadster to run 200 MPH at Bonneville Salt Flats setting the record August 7th 2021 at 205.744 MPH
Ronnieroadster is offline   Reply With Quote
Old 01-02-2019, 11:12 PM   #6
fordor41
Senior Member
 
fordor41's Avatar
 
Join Date: Oct 2011
Location: elmira,ny
Posts: 1,505
Default Re: Petronix ignition question

Sponsored Links (Register now to hide all advertisements)
I've found PertroniX ignitions about bullet proof. Had one go bad but it was caused by my coil going south. 15 yrs or so and 10's of thousands of miles.
.
fordor41 is offline   Reply With Quote
Old 01-03-2019, 12:27 AM   #7
Drbrown
Senior Member
 
Drbrown's Avatar
 
Join Date: Oct 2013
Location: Glens Falls NY
Posts: 1,267
Default Re: Petronix ignition question

My '47 had a pentronix for many years, together with copper wires, but then the alternator decided to put out too much voltage and started killing the pentronix modules, one after another at the rate of $100 each. In some known cases, as soon as voltage hit more than 14.6 they would blow. After many replacements (modules and alternators) and lots of head-scratching with Bubba, I had Charlie NY set me up with a stock points crab unit and a Blue Flame coil, and Bubba set me up with a back-up unit to store in my trunk. No more problems; starts /runs like a charm. Still using the copper wires.
Drbrown is offline   Reply With Quote
Old 01-03-2019, 11:59 AM   #8
Init1
Senior Member
 
Init1's Avatar
 
Join Date: May 2010
Location: Oregon City, Oregon
Posts: 208
Default Re: Petronix ignition question

I use Pertronix in all my cars. I've never had a problem. I also use copper Packard 440 plug wires.
I do carry conventional points just in case.
Init1 is offline   Reply With Quote
Old 01-04-2019, 12:19 AM   #9
Kahuna
Senior Member
 
Kahuna's Avatar
 
Join Date: May 2010
Location: NorCal
Posts: 2,617
Default Re: Petronix ignition question

I also use the Pertronix with Packard 440 wire. My 39 is still going after 29 years & the 32 more than 11.
Just lucky, I guess. I'm too lazy to change them now
Kahuna is offline   Reply With Quote
Old 01-04-2019, 12:35 AM   #10
Vintage Copper 47
Senior Member
 
Vintage Copper 47's Avatar
 
Join Date: Mar 2017
Location: The sleepy San Fernando Valley
Posts: 394
Default Re: Petronix ignition question

Quote:
Originally Posted by Jack E/NJ View Post
Nothing like a good set of points, condenser & run resistor to solve all your 6 & 12 volt ignition woes. 8^) Jack E?NJ
This is why I choose not to go electronic.. I don't want the hassle of switching wires!
__________________
WALT

"We sleep safe in our beds because rough men stand ready in the night to visit violence on those who would do us harm".

"Old enough for the experience & too young to know better"
Vintage Copper 47 is offline   Reply With Quote
Old 01-04-2019, 05:59 PM   #11
[email protected]
Senior Member
 
Join Date: Nov 2015
Location: Sharon, Conn.
Posts: 112
Default Re: Petronix ignition question

Thanks for all of the comments. It's probably a good idea to go with carbon track wires. Really appreciate the input!

Bill in Conn.
patbill@megahits.com is offline   Reply With Quote
Old 01-04-2019, 06:38 PM   #12
Greg58
Senior Member
 
Greg58's Avatar
 
Join Date: Jul 2016
Location: Newnan Georgia
Posts: 206
Default Re: Petronix ignition question

I changed my 50 to the pertronix early 2018 along with resistor wires because of radio noise, my family gave me a custom auto sound radio for Christmas 2017. Interference would get really bad as I gained engine rpm, now the radio is clear all the time. Time will tell if it lasts but for now I can listen to Merle when I want.
__________________
Greg
Greg58 is offline   Reply With Quote
Old 01-04-2019, 08:51 PM   #13
1948F-1Pickup
Senior Member
 
1948F-1Pickup's Avatar
 
Join Date: Oct 2015
Location: Socal
Posts: 794
Default Re: Petronix ignition question

They sucked when they were called PerLux and they still suck as Pertronix.
(I ran them merely as a trigger for either Jacobs or MSD boxes back in the
day) Inside a distributor where it's hot..... just what switching electronics
like for a working environment..... sarcasm.
After having more than 2 or 3 failures over about a 5 year period, I gave
up on them.
Unilite and Alison opto electric were other solutions looking for problems.
(both with sensitive electronics around searing underhood heat)

Quote:
Originally Posted by 51 MERC-CT View Post
Nothing new, I have been running Pertronix 12 volt conversion for well over 10 years and seem to recall that it was a recommendation back then just as this one is as provided with Mallory Unilite conversions.
You may well get away with what you are running but if you experience problems it may be time to revisit the ignition wire recommendation.
Hadn't heard that about solid core wires...... seems like they're trying to
lump spiral wound core wires into that as well.
For years now I've run spiral core secondary wires, a gen 1 Jacobs box and a Hays
reluctor with a Chrysler style PU coil for a trigger. I have that same setup on a few
vehicles, including my F-1 truck's flathead.

Last edited by 1948F-1Pickup; 01-04-2019 at 08:58 PM.
1948F-1Pickup is offline   Reply With Quote
Old 01-04-2019, 11:06 PM   #14
51 MERC-CT
Senior Member
 
51 MERC-CT's Avatar
 
Join Date: May 2010
Location: East Hartford, Ct
Posts: 5,898
Default Re: Petronix ignition question

Quote:
Originally Posted by 1948F-1Pickup View Post



Hadn't heard that about solid core wires...... seems like they're trying to
lump spiral wound core wires into that as well.
For years now I've run spiral core secondary wires, a gen 1 Jacobs box and a Hays
reluctor with a Chrysler style PU coil for a trigger. I have that same setup on a few
vehicles, including my F-1 truck's flathead.
Lumping spiral wound core wires into what?
They are in fact recommending the use of spiral core wires.
Don't know what you are talking about.
__________________
DON'T RECALL DOING SOMETHING FOR MYSELF BASED ON SOMEONE ELSE'S LIKES OR DISLIKES
51 MERC-CT is offline   Reply With Quote
Old 01-04-2019, 11:26 PM   #15
fordor41
Senior Member
 
fordor41's Avatar
 
Join Date: Oct 2011
Location: elmira,ny
Posts: 1,505
Default Re: Petronix ignition question

Quote:
Originally Posted by fordor41 View Post
I've found PertroniX ignitions about bullet proof. Had one go bad but it was caused by my coil going south. 15 yrs or so and 10's of thousands of miles.
.
When mine went bad I had a spare. The new one wouldn't work either. I called them and they said to return them (both at least 8 yrs old). They sent me 2 new ones, free, with instructions on checking my coil. Great service
fordor41 is offline   Reply With Quote
Old 01-05-2019, 12:54 AM   #16
50fordcoupeman
Senior Member
 
50fordcoupeman's Avatar
 
Join Date: Mar 2016
Location: LaGrande Oregon
Posts: 865
Default Re: Petronix ignition question

I run Pertronix on two engines without a hitch-4 years now on both.
50fordcoupeman is offline   Reply With Quote
Old 01-05-2019, 07:48 AM   #17
Gene1949
Senior Member
 
Gene1949's Avatar
 
Join Date: Jun 2016
Location: Pahrump, NV
Posts: 372
Default Re: Petronix ignition question

Greg58
How do you like the custom auto sound radio?? The fitment and sound quality. My wife is very adamant on keeping the dash stock.
thankx
Gene1949 is offline   Reply With Quote
Old 01-05-2019, 08:56 AM   #18
Greg58
Senior Member
 
Greg58's Avatar
 
Join Date: Jul 2016
Location: Newnan Georgia
Posts: 206
Default Re: Petronix ignition question

Gene its good, it fits the dash without alterations, comes with a face plate that makes a clean look. The sound is good. The problem is finding high quality speakers, I've tried a few but can't find the look I'm after. I want the wedge style for the package tray like everyone had in the 70's. I found some high quality marine speakers and mounted them under the dash at the top of each kick panel, the sound is not BOSE but is good.
__________________
Greg
Greg58 is offline   Reply With Quote
Old 01-05-2019, 11:54 AM   #19
1948F-1Pickup
Senior Member
 
1948F-1Pickup's Avatar
 
Join Date: Oct 2015
Location: Socal
Posts: 794
Default Re: Petronix ignition question

Quote:
Originally Posted by 51 MERC-CT View Post
Lumping spiral wound core wires into what?
They are in fact recommending the use of spiral core wires.
Don't know what you are talking about.
Spiral wound are characterized as solid core. They don't suppress
by resistance. They also can (and do) false trigger. The Mallory statement is BS.
When spiral wound wires wear out (like all secondary wires), they leak.
1948F-1Pickup is offline   Reply With Quote
Old 01-05-2019, 01:29 PM   #20
Gene1949
Senior Member
 
Gene1949's Avatar
 
Join Date: Jun 2016
Location: Pahrump, NV
Posts: 372
Default Re: Petronix ignition question

Thankx Greg
Gene1949 is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 02:38 PM.