The Ford Barn

Lyle · 10-15-2010, 09:59 PM

I received a phone call from a fellow (Arizona I think)wanting parts off my 53 mercury.Please call. My Grand Daughter erased my Call log. I have removed the speedometer,light switch, radio and other stuff. Please call. Also Mr. Merc Cruzer I have the horn ring, steering wheel and center emblem. Will send soon. I have a pair of finder skirts. If some one wont's them I am not advertising for sale. The stuff is for a person that needs them for a hopefully keeper project. The skirts are A 1 condition. I think they will fit fords also I held one of them up to my 52 ford looked like a fit also. Lyle

37fatfender · 10-26-2010, 05:42 PM

I need a 49-53 merc pass oil pan.

rotorwrench · 10-26-2010, 06:16 PM

There are two distinctly different style pans in the 49 to 53 Mercury range. The 49 to early 51 had the rear sump with the three studs on the bottom that attach to the starter plate/ bellhousing assembly. The mid 51 to end did away with the three studs but is still pretty much the same. The 52 & 53 ribbed center sump pan is more like the center sump pan on the 49 thru 51 Ford car and same as the 52 & 53 Ford car pan.

If this is going into an older car with wishbone front axle set up, you will need a pan from a 49 thru 51 Mercury.

Kerby

37fatfender · 10-26-2010, 07:12 PM

Thanks, I appreciate the info, that helps very much. I'll need the 49-51 rear sump. I am trying to get my 8ba in a 40, but have run into steering linkage clearence issures. I was attempting a rear sump truck pan but that ain't workin.........

Merc Cruzer · 10-26-2010, 08:00 PM

Lyle:

Sent you a PM

Roy
Conifer, Colorado

Lyle · 10-26-2010, 08:45 PM

Sponsored Links (Register now to hide all advertisements)

I have a 49 mercury pan. I do not think you would wont it. It is rusted through in places. the block was cracked and everything was rusted and or rust pitted bad.The intake,heads,bell housing were the only thing that looked worth a flip.

Lyle · 10-26-2010, 08:48 PM

Hello Merc Cruzer I talked to you over the phone. Thanks for the call back. I have your number now!

r doud · 08-24-2011, 01:54 PM

Hi, i am looking for rocker molding and a trunk lock for a two door mercury Monterrey. also some emblems . thanks Bob

10-15-2010, 09:59 PM	#1
Lyle Senior Member Join Date: May 2010 Location: Tyler Texas Posts: 226	53 Mercury parts I received a phone call from a fellow (Arizona I think)wanting parts off my 53 mercury.Please call. My Grand Daughter erased my Call log. I have removed the speedometer,light switch, radio and other stuff. Please call. Also Mr. Merc Cruzer I have the horn ring, steering wheel and center emblem. Will send soon. I have a pair of finder skirts. If some one wont's them I am not advertising for sale. The stuff is for a person that needs them for a hopefully keeper project. The skirts are A 1 condition. I think they will fit fords also I held one of them up to my 52 ford looked like a fit also. Lyle

10-26-2010, 05:42 PM	#2
37fatfender Senior Member Join Date: May 2010 Location: Mesquite, NV / Gurnee, IL Posts: 298	Re: 53 Mercury parts I need a 49-53 merc pass oil pan.

10-26-2010, 06:16 PM	#3
rotorwrench Senior Member Join Date: Jun 2010 Location: San Antonio, Texas Posts: 16,431	Re: 53 Mercury parts There are two distinctly different style pans in the 49 to 53 Mercury range. The 49 to early 51 had the rear sump with the three studs on the bottom that attach to the starter plate/ bellhousing assembly. The mid 51 to end did away with the three studs but is still pretty much the same. The 52 & 53 ribbed center sump pan is more like the center sump pan on the 49 thru 51 Ford car and same as the 52 & 53 Ford car pan. If this is going into an older car with wishbone front axle set up, you will need a pan from a 49 thru 51 Mercury. Kerby Last edited by rotorwrench; 10-26-2010 at 06:24 PM.

10-26-2010, 07:12 PM	#4
37fatfender Senior Member Join Date: May 2010 Location: Mesquite, NV / Gurnee, IL Posts: 298	Re: 53 Mercury parts Thanks, I appreciate the info, that helps very much. I'll need the 49-51 rear sump. I am trying to get my 8ba in a 40, but have run into steering linkage clearence issures. I was attempting a rear sump truck pan but that ain't workin.........

10-26-2010, 08:00 PM	#5
Merc Cruzer Senior Member Join Date: Jul 2010 Location: Conifer, Colorado Posts: 2,429	Re: 53 Mercury parts Lyle: Sent you a PM Roy Conifer, Colorado

10-26-2010, 08:45 PM	#6
Lyle Senior Member Join Date: May 2010 Location: Tyler Texas Posts: 226	Re: 53 Mercury parts Sponsored Links (Register now to hide all advertisements) I have a 49 mercury pan. I do not think you would wont it. It is rusted through in places. the block was cracked and everything was rusted and or rust pitted bad.The intake,heads,bell housing were the only thing that looked worth a flip.

10-26-2010, 08:48 PM	#7
Lyle Senior Member Join Date: May 2010 Location: Tyler Texas Posts: 226	Re: 53 Mercury parts Hello Merc Cruzer I talked to you over the phone. Thanks for the call back. I have your number now!

08-24-2011, 01:54 PM	#8
r doud Junior Member Join Date: Dec 2010 Posts: 5	Re: 53 Mercury parts Hi, i am looking for rocker molding and a trunk lock for a two door mercury Monterrey. also some emblems . thanks Bob