Go Back   The Ford Barn > General Discussion > Early V8 (1932-53)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 09-15-2019, 09:50 PM   #1
Bubsyouruncle
Senior Member
 
Join Date: Aug 2013
Location: Gurnee, Illinois
Posts: 269
Default Ignition timing

1947 59A standard ignition
Looking down on the distributor sitting on my bench. The vacuum brake is at the top.
The right ignition point gauges at about .015. Which is in spec.
The left one, however, gauges at .009 or a little less.
What effect does the smaller gap have, if any, on the timing?
What effect does the smaller gap have, if any, on anything else?
Bubsyouruncle is offline   Reply With Quote
Old 09-16-2019, 07:08 AM   #2
JWL
Member Emeritus
 
Join Date: May 2010
Location: Fitzgerald, Georgia
Posts: 2,204
Default Re: Ignition timing

Smaller gaps delay or retard timing. Gaps too small can reduced point life and foul or shunt as a result of corrosion/erosion/dirt.
JWL is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 09-16-2019, 07:37 AM   #3
G.M.
Senior Member
 
Join Date: May 2010
Location: Florida and Penna.
Posts: 4,471
Default Re: Ignition timing

The points are NOT set with a feeler gauge. They are
on a Ford~Heyer strobe machine on a dwell meter. G.M.
__________________
www.fordcollector.com
G.M. is offline   Reply With Quote
Old 09-16-2019, 08:43 AM   #4
fordwife
Senior Member
 
Join Date: Dec 2015
Posts: 287
Default Re: Ignition timing

There are other ways to do this, such as a sun distributor machine or a k. r. Wilson timing fixture. My ford service manual calls for .014 to .016 setting and shows how to set the points using a straight edge.
fordwife is offline   Reply With Quote
Old 09-16-2019, 09:47 AM   #5
marko39
Senior Member
 
Join Date: Oct 2016
Location: harpursville ny
Posts: 1,038
Default Re: Ignition timing

When set up on a sun machine,the right points are adj. to an initial dwell with the left ones blocked off with a piece of fiber such as a match pack. That is then removed and the total dwell is set buy adj. the left set.
marko39 is offline   Reply With Quote
Old 09-16-2019, 03:37 PM   #6
FlatheadTed
Senior Member
 
FlatheadTed's Avatar
 
Join Date: May 2010
Location: Auckland
Posts: 4,691
Send a message via AIM to FlatheadTed
Default Re: Ignition timing

Sponsored Links (Register now to hide all advertisements)
The 9th gap will most likely add a premature failure facture into it due to the rubbing block ware ,the and closing up .015 ect is only a starting measurement ,could end up different at the end of adjustment .I noticed in the U tube Ford Factory video setting them ,looks like no feeler gauges are used ,some sort of Heyer or Vane machine ,
__________________
http://www.flatheadted.com


Flathead Ted brake Floaters ,

Last edited by FlatheadTed; 09-16-2019 at 06:24 PM.
FlatheadTed is offline   Reply With Quote
Old 09-16-2019, 09:09 PM   #7
GB SISSON
Senior Member
 
GB SISSON's Avatar
 
Join Date: Jan 2014
Location: Orcas Island Washington
Posts: 4,846
Default Re: Ignition timing

Anyone have a pic of the straightedge method? I remember seeing it in one of the books I have somewhere. Thanks
__________________
Owner/Operator of 'Jailbar Ranch' on the side of Mt. Pickett. Current stable consists of 1946 1/2 ton pickup turned woodie wagon with FH V8, 1947 Tonner Pickup (red) mostly stock with exception of a cummins 6at turbo diesel, 1946 Tonner Pickup (green) with 226 cu in 6 cyl flathead, 1979 Toyota landcruiser wagon, completely encased in 1947 Ford Jailbar sheet metal. Ok, cornbinder rear fenders..... 'Rusty ol' floorboards, hot on their feet' (Alan Jackson)
GB SISSON is offline   Reply With Quote
Old 09-16-2019, 09:36 PM   #8
slowforty
Senior Member
 
slowforty's Avatar
 
Join Date: May 2010
Location: Tinley Park Ill
Posts: 1,055
Default Re: Ignition timing

Some of the early edition Motor Manuals have it in them probably before 1949.
Those manuals dont bring a lot of money
slowforty is offline   Reply With Quote
Old 09-16-2019, 09:38 PM   #9
JSeery
Member Emeritus
 
JSeery's Avatar
 
Join Date: Nov 2012
Location: Wichita KS
Posts: 16,132
Default Re: Ignition timing

Look on VanPelts site.
JSeery is offline   Reply With Quote
Old 09-16-2019, 11:23 PM   #10
FlatheadTed
Senior Member
 
FlatheadTed's Avatar
 
Join Date: May 2010
Location: Auckland
Posts: 4,691
Send a message via AIM to FlatheadTed
Default Re: Ignition timing

Here's some tips
http://www.btc-bci.com/~billben/flathead.htm
Distributor timing .32to 48 timing fixture don't need em ,
__________________
http://www.flatheadted.com


Flathead Ted brake Floaters ,
FlatheadTed is offline   Reply With Quote
Old 09-16-2019, 11:57 PM   #11
35fordtn
Senior Member
 
35fordtn's Avatar
 
Join Date: Aug 2010
Location: McMinnville, TN
Posts: 2,327
Default Re: Ignition timing

If you are using quality points although not ideal you could set them by gap not dwell. If you are using cheap quality points it’s a crap shoot. Send it to someone with a sun machine and for little to no money they can adjust to the proper dwell and set the timing.
35fordtn is offline   Reply With Quote
Old 09-17-2019, 05:17 PM   #12
Lawrie
Senior Member
 
Lawrie's Avatar
 
Join Date: May 2010
Location: Qld, Australia
Posts: 4,195
Default Re: Ignition timing

There are static jigs around for setting the dwell, there are two on ebay now,exspensive though.
keep a lookout for them .
Lawrie
Lawrie is offline   Reply With Quote
Old 09-17-2019, 07:29 PM   #13
edhd58
Senior Member
 
edhd58's Avatar
 
Join Date: Jul 2014
Location: Guston,ky
Posts: 653
Default Re: Ignition timing

I am a poor guy, I set mine with a set of feeler gauges, like my Dad did before me all the way up till mid 70s when Dad 75 Lincoln.
edhd58 is offline   Reply With Quote
Old 09-17-2019, 07:36 PM   #14
tubman
Senior Member
 
tubman's Avatar
 
Join Date: Dec 2013
Location: Minnesota, Florida Keys
Posts: 10,260
Default Re: Ignition timing

Ya' know, I was in your camp until about 3 months ago, when I replaced the points on the Mallory dual point on the '51 Merc in my '51 Ford. For some reason, that particular setup didn't have the little slots they usually have where you can insert a small screwdriver to move the points a little bit at a time. I bought an old universal dwell/tach meter off of eBay for $20. Now I realize I should have done it 50 years ago.
tubman is offline   Reply With Quote
Old 09-18-2019, 09:45 AM   #15
Hoop
Senior Member
 
Hoop's Avatar
 
Join Date: May 2010
Location: Jacksonville FL
Posts: 1,137
Default Re: Ignition timing

One of the problems in these discussions is terminology.

TIMING an early flathead distributor is a little different than TESTING a distributor.

TIMING involves setting the dwell and adjusting the initial advance.

TESTING means checking the distributor for wear, bad parts, faulty operation, etc.

TIMNG and TESTING can be done at the same time ... with aging distributors and questionable new parts, it's a good idea.

BUT, claiming that one cannot TIME a flathead distributor using feeler gauges to set the dwell ... ?

THINK about it. Ford designed, patented and produced the distributor with the intent of having points set with feeler gauges. Ford did not design it so that owners had to send their distributors to G.M. and Skip Haney to be timed.:roll eyes:

The misinformation, much from using the wrong descriptions, has given the distributors a bad reputation.

Am all for testing distributors. But, when someone asks how to time one, please give a knowledgable answer.
__________________
"Remember that when it comes to intelligence, half of all of us are below average."
Hoop is offline   Reply With Quote
Old 09-18-2019, 09:54 AM   #16
35fordtn
Senior Member
 
35fordtn's Avatar
 
Join Date: Aug 2010
Location: McMinnville, TN
Posts: 2,327
Default Re: Ignition timing

Hoop i would agree with that last part if all we used were genuine Ford parts. Ever set up a 32-36 with a feeler gauge using reproduction points and checked the dwell?

The 49 and later guys and 4/6 cylinder guys should have no issues using a feeler gauge to set dwell
35fordtn is offline   Reply With Quote
Old 09-18-2019, 10:19 AM   #17
Hoop
Senior Member
 
Hoop's Avatar
 
Join Date: May 2010
Location: Jacksonville FL
Posts: 1,137
Default Re: Ignition timing

Michael,

The "knowledgable answer" would include exactly what you've said.

Further, there is no guarantee that sending your distributor out for rebuilding will have it TIMED correctly. That includes units that have been "set up" on Sun or Allen strobers and the rebuilder does not understand initial advance. There are a bunch of guys running around losing 20% or more of their advance because of improper settings.

I know you are well aware of the issue and that distributors leave your shop correctly set.
__________________
"Remember that when it comes to intelligence, half of all of us are below average."
Hoop is offline   Reply With Quote
Old 09-18-2019, 10:27 AM   #18
35fordtn
Senior Member
 
35fordtn's Avatar
 
Join Date: Aug 2010
Location: McMinnville, TN
Posts: 2,327
Default Re: Ignition timing

Hoop,
Yes I agree. I tested many “rebuilt” distributors that the initial timing was not set they just seemed to guess at it.
35fordtn is offline   Reply With Quote
Old 09-18-2019, 10:34 AM   #19
philipswanson
Senior Member
 
Join Date: Oct 2015
Location: Bonita, CA
Posts: 1,374
Default Re: Ignition timing

Quote:
Originally Posted by marko39 View Post
When set up on a sun machine,the right points are adj. to an initial dwell with the left ones blocked off with a piece of fiber such as a match pack. That is then removed and the total dwell is set buy adj. the left set.
That's how I do it. Also what Bubba recommends.
philipswanson is offline   Reply With Quote
Old 09-18-2019, 12:14 PM   #20
flatjack9
Senior Member
 
flatjack9's Avatar
 
Join Date: May 2010
Location: Oshkosh, Wi
Posts: 4,516
Default Re: Ignition timing

Also the way Ford recommends.
flatjack9 is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 03:09 PM.