The Ford Barn

Safari bob · 05-22-2023, 09:35 PM

I have a 4 speed transmission that I believe started it life in a ford 150 truck. It was adapted to fit a Model A. I am searching for a part number for the clutch disc. The hub of the Model A clutch disc is too large. Any help would be very much appreciated.

J Franklin · 05-22-2023, 11:20 PM

Find the disk for that year transmission.

kenparker0703 · 05-23-2023, 07:52 AM

The disc that fits the 1984 - 1987 F150 truck will not work in the Model A adaption. Disc to large diameter.

I ordered and received one that will work last month. It is installed now.
Part number D923. Ordered thru Auto Zone. Clutch disc fits the 1969 Ford Falcon with a 200 cu in engine.

Safari bob · 05-23-2023, 04:45 PM

The F 150's had n 11" disc where mine is 9". Thanks for responding.

Safari bob · 05-23-2023, 04:47 PM

I am off too Auto Zone to place an order. I assume you have the converted F 150 Transmission as I do. Easy to drive with it but a little tough on some hills.
Thanks for your response.

Bob

AL in NY · 05-23-2023, 05:28 PM

Sponsored Links (Register now to hide all advertisements)

Go to your locate parts store and get a clutch out of a 1986 T-Bird with the 4 cylinder turbo engine. The clutch is 9" with the correct 1 1/16" x 10 spline.

Safari bob · 05-26-2023, 03:04 PM

Thank You for your response. I have ordered that part.

Bob

Gene F · 05-26-2023, 04:23 PM

This is great information guys. My local NAPA store has one counter clerk that knows about parts. I have a streetrod, that I did not engineer. The original builder died. Sometimes finding the right part is like a treasure hunt. I have helped myself more than anything, or any one else. That one good counter person is not too bad, but I have to point him in a direction.

AutoZone is a complete joke as far as parts knowledge. Advance is not too bad if I get one guy. He does at least try.

05-22-2023, 09:35 PM	#1
Safari bob Member Join Date: Sep 2010 Posts: 46	Clutch disk - 4 speed transmission I have a 4 speed transmission that I believe started it life in a ford 150 truck. It was adapted to fit a Model A. I am searching for a part number for the clutch disc. The hub of the Model A clutch disc is too large. Any help would be very much appreciated.

05-22-2023, 11:20 PM	#2
J Franklin Senior Member Join Date: May 2010 Location: Oregon Posts: 5,963	Re: Clutch disk - 4 speed transmission Find the disk for that year transmission.

05-23-2023, 07:52 AM	#3
kenparker0703 Member Join Date: Sep 2018 Posts: 88	Re: Clutch disk - 4 speed transmission The disc that fits the 1984 - 1987 F150 truck will not work in the Model A adaption. Disc to large diameter. I ordered and received one that will work last month. It is installed now. Part number D923. Ordered thru Auto Zone. Clutch disc fits the 1969 Ford Falcon with a 200 cu in engine.

05-23-2023, 04:45 PM	#4
Safari bob Member Join Date: Sep 2010 Posts: 46	Re: Clutch disk - 4 speed transmission The F 150's had n 11" disc where mine is 9". Thanks for responding.

05-23-2023, 04:47 PM	#5
Safari bob Member Join Date: Sep 2010 Posts: 46	Re: Clutch disk - 4 speed transmission I am off too Auto Zone to place an order. I assume you have the converted F 150 Transmission as I do. Easy to drive with it but a little tough on some hills. Thanks for your response. Bob

05-23-2023, 05:28 PM	#6
AL in NY Senior Member Join Date: May 2010 Location: Southern Upstate New York Posts: 1,160	Re: Clutch disk - 4 speed transmission Sponsored Links (Register now to hide all advertisements) Go to your locate parts store and get a clutch out of a 1986 T-Bird with the 4 cylinder turbo engine. The clutch is 9" with the correct 1 1/16" x 10 spline. __________________ AL in NY

05-26-2023, 03:04 PM	#7
Safari bob Member Join Date: Sep 2010 Posts: 46	Re: Clutch disk - 4 speed transmission Thank You for your response. I have ordered that part. Bob

05-26-2023, 04:23 PM	#8
Gene F Senior Member Join Date: Mar 2012 Location: Ohio Posts: 1,973	Re: Clutch disk - 4 speed transmission This is great information guys. My local NAPA store has one counter clerk that knows about parts. I have a streetrod, that I did not engineer. The original builder died. Sometimes finding the right part is like a treasure hunt. I have helped myself more than anything, or any one else. That one good counter person is not too bad, but I have to point him in a direction. AutoZone is a complete joke as far as parts knowledge. Advance is not too bad if I get one guy. He does at least try.