|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
04-04-2024, 12:00 AM | #1 |
Member
Join Date: May 2017
Posts: 56
|
D Nut Hole Punch
Hello all,
Making progress on the 1931 Pickup I recently purchased. I have the cab off the frame and replacing the floor channels/ cross brases when I discovered there are D Nuts for the wooden floor board and rivets. I want to find a D Nut Hole Punch tool, but I need to know what exactly the size D Nuts are offered in the catalogs, as McMasters is pretty pricy to just guess https://www.mcmaster.com/products/d-...ockout-punches Also, does anyone have a drawing or any information that is specific about rivet sizes for these cross brace pieces? |
04-04-2024, 06:11 AM | #2 | |
Senior Member
Join Date: May 2010
Location: Eastern Tennessee
Posts: 11,543
|
Re: D Nut Hole Punch
Quote:
|
|
Sponsored Links (Register now to hide all advertisements) |
|
04-04-2024, 01:17 PM | #3 |
Senior Member
Join Date: Jun 2010
Location: San Antonio, Texas
Posts: 16,483
|
Re: D Nut Hole Punch
From the looks of the illustration for the McMaster Carr punches, they are a different shape. The Model A "D" nuts only have a small area of flat for the diameter of the hole. I have always done them the hard way. I compass the circle on the known center line then straight edge the flat for size in the original location. I use a single flute step drill to enlarge the starter hole then grind & file the aperture to fit the D-nut going in. I go for as tight a fit as I can get prior to setting the D-nut.
To fabricate the die it takes to punch an aperture of that shape would take a special broach to get it right. Not impossible but the equipment to do it is expensive. The die and the punch have to have hardened edges to use them on thick sheet metal such as is common to the model A in the places where they were used. The aperture shape is common to key lock cylinders but they are generally a larger size. |
04-04-2024, 01:32 PM | #4 |
Senior Member
Join Date: Jun 2015
Location: Signal Mtn, TN (SE TN)
Posts: 2,378
|
Re: D Nut Hole Punch
For the minimal amount required, you’ll be best served to follow Brent’s info.
Unless you’re doing many, you won’t recoup the outlay. Also, you need to decide what actual machine/ punch will do the job and then seek the actual punch. I have them but the punch fits a 5 ton foot punch; therefore not real portable. You bring the job to the punch; not the punch to the job |
04-05-2024, 12:01 AM | #5 |
Member
Join Date: May 2017
Posts: 56
|
Re: D Nut Hole Punch
All great advice, and I realize now how much work and effort there is in punching a "D" hole...
Here's my thought, to cut out the original "D" nuts from the damaged section and weld them into the cross pieces. Thoughts? |
04-05-2024, 06:23 AM | #6 |
Senior Member
Join Date: May 2010
Location: Eastern Tennessee
Posts: 11,543
|
Re: D Nut Hole Punch
Sponsored Links (Register now to hide all advertisements)
|
04-05-2024, 07:25 AM | #7 |
Senior Member
Join Date: May 2010
Location: Long Island, NY
Posts: 3,498
|
Re: D Nut Hole Punch
Make templates from card-stock of the various size D-Nuts you need to install. Tape the template in place & use a marking pen to transfer the shape onto the body. Drill an under-size diameter hole through the shape, then use a router bit in a Dremel type tool to finish the shape.
You can weld, solder or clinch the D-Nuts into place.
__________________
Bob Bidonde |
04-05-2024, 09:29 AM | #8 |
Senior Member
Join Date: Jun 2015
Location: Red Deer, Alberta
Posts: 5,067
|
Re: D Nut Hole Punch
I would drill a hole (the diameter of the D from the flat side to the opposite side), then take a rat tail (tapered round) file, (the diameter of the wide part of the D), grind a flat on one side to make a "D" file, then file out the hole.
__________________
If you don't hear a rumor by 10 AM, start one!. Got my education out behind the barn! |
04-06-2024, 09:13 AM | #9 |
Senior Member
Join Date: May 2012
Location: Chillicothe, Missouri
Posts: 1,204
|
Re: D Nut Hole Punch
I was just gonna post what Katy just posted. We both have same idea!
__________________
"If I asked people what they wanted they would have said faster horses." -Henry Ford "Primitive technology is not a design flaw" 1928 Ford Model A Roadster Pickup 1930 Gordon Smith Air Compressor 1941 Willy's Pickup 1960 Thunderbird-For Sale 1964 Buick Riviera 2x4 425 1965 Pontiac GTO, 455 Super Duty 2004 Dodge Ram SRT-10, V-10 Viper 1977 Charger Jet Boat,460 Ford,Jacuzzi Jet Front Engine Nostalgia Dragster,Supercharged 296 "Fullrace Flathead" Ford Engine Build up on DVD ask |
|
|
Sponsored Links (Register now to hide all advertisements) |
|