The Ford Barn

MrBruce · 02-15-2016, 04:01 PM

Has anyone used the new points from Standard? I only say new because I was just showed a set this week and hadn't seen them or heard anything about them. The part number on them is FD 1718 and the major change is the wear block is made of modern material. Otherwise I think they are just like the original? That's the main complaint for going with modern points over the past years? contact_set_oem_fd1718.jpg

Flathead · 02-15-2016, 05:34 PM

Very interesting, I didn't know these were available.

MrBruce · 02-15-2016, 05:45 PM

Flathead
I didn't know until last week one of our members asked if I had seen them. I said I wasn't aware of any new points and then looked at them. I googled that number online and they were all over. The one thing I noticed is the price is quite high I thought. I paid $12.00 and online they were anywhere from $29.00 - $15.00. I might start to build some distributors with these but will try to get the price down.

1955cj5 · 02-15-2016, 07:36 PM

I recently bought points from O'reilly ...was a little surprised that they had them..

BWD brand, but they look just like the Standard brand pictured above...

http://www.oreillyauto.com/site/c/de...A123/02766.oap

http://www.summitracing.com/parts/smp-fd1718

What would an original points set look like?

The picture is of the BWD set being installed..

Mitch//pa · 02-15-2016, 08:22 PM

I use the standard points all the time I get them from my shop jobber...

The PN as mentioned is FD1718
The condenser is FD11 and have yet to have one fail...I think there's are short proof also

redmodelt · 02-16-2016, 11:30 AM

Sponsored Links (Register now to hide all advertisements)

Does anyone know if they make them for the "B" distributor?

BILL WILLIAMSON · 02-16-2016, 11:51 AM

Remember, QUICK & UNEVEN rubbing block wear can happen, if the pivot post for the point arm is LOOSE & WOBBLY! It can be tightened, under the plate, with a punch & a TAP-TAP-TAP! Both of mine were LOOSE as a GOOSE!
Bill Tap

02-15-2016, 04:01 PM	#1
MrBruce Senior Member Join Date: Oct 2014 Location: Charlotte, NC Posts: 310	New Distributor Points for Model A Has anyone used the new points from Standard? I only say new because I was just showed a set this week and hadn't seen them or heard anything about them. The part number on them is FD 1718 and the major change is the wear block is made of modern material. Otherwise I think they are just like the original? That's the main complaint for going with modern points over the past years? contact_set_oem_fd1718.jpg

02-15-2016, 05:34 PM	#2
Flathead Senior Member Join Date: May 2010 Location: Southern Maine Posts: 1,497	Re: New Distributor Points for Model A Very interesting, I didn't know these were available.

02-15-2016, 05:45 PM	#3
MrBruce Senior Member Join Date: Oct 2014 Location: Charlotte, NC Posts: 310	Re: New Distributor Points for Model A Flathead I didn't know until last week one of our members asked if I had seen them. I said I wasn't aware of any new points and then looked at them. I googled that number online and they were all over. The one thing I noticed is the price is quite high I thought. I paid $12.00 and online they were anywhere from $29.00 - $15.00. I might start to build some distributors with these but will try to get the price down.

02-16-2016, 11:30 AM	#6
redmodelt Senior Member Join Date: May 2010 Location: Portland OR Posts: 6,340	Re: New Distributor Points for Model A Sponsored Links (Register now to hide all advertisements) Does anyone know if they make them for the "B" distributor?

02-16-2016, 11:51 AM	#7
BILL WILLIAMSON Senior Member Join Date: Dec 2010 Location: FRESNO, CA Posts: 12,560	Re: New Distributor Points for Model A Remember, QUICK & UNEVEN rubbing block wear can happen, if the pivot post for the point arm is LOOSE & WOBBLY! It can be tightened, under the plate, with a punch & a TAP-TAP-TAP! Both of mine were LOOSE as a GOOSE! Bill Tap __________________ "THE ASSISTANT GURU OF STUFF"