Go Back   The Ford Barn > General Discussion > Early V8 (1932-53)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 09-20-2016, 05:54 PM   #1
Bdupes
Junior Member
 
Join Date: Sep 2016
Location: Michigan
Posts: 6
Default 1939 - 1942 brake problems

I have a 1937 ford truck with the 1939 - 1942 drum brakes, I had a L/F wheel cylinder go bad and for the life of me I can't get the brakes back. I'm sure I'm missing something small. I have replaced all the wheel cylinders on the truck but I can't get the pedal back. any help is greatly appreciated. the truck has a master cylinder from a 1968 chev 4 drum brake system on it. prior to losing the L/F wheel cylinder the brakes were fine. PLEASE HELP
Bdupes is offline   Reply With Quote
Old 09-20-2016, 05:55 PM   #2
petehoovie
Senior Member
 
petehoovie's Avatar
 
Join Date: May 2015
Posts: 7,933
Default Re: 1939 - 1942 brake problems

DOT 5 Brake Fluid???
__________________
The only thing nice about being imperfect is the joy it brings to others....

"Silver rings, your butt! Them's washers!"
"We shot our way out of that town for a dollar's worth of steel holes!" - from 'The Wild Bunch' - 1969

https://www.youtube.com/watch?v=7NReUd2_0u0
petehoovie is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 09-20-2016, 06:05 PM   #3
hotcoupe
Senior Member
 
hotcoupe's Avatar
 
Join Date: May 2010
Location: imperial,mo
Posts: 685
Default Re: 1939 - 1942 brake problems

Unless you have a monstrous leak, my guess is the master cylinder is at fault. Did you bench bleed the master cylinder?

Sent from my 6045O using Tapatalk
hotcoupe is offline   Reply With Quote
Old 09-20-2016, 06:10 PM   #4
Bdupes
Junior Member
 
Join Date: Sep 2016
Location: Michigan
Posts: 6
Default Re: 1939 - 1942 brake problems

bench bled the master and put a new one in there
Bdupes is offline   Reply With Quote
Old 09-20-2016, 06:37 PM   #5
Talkwrench
Senior Member
 
Talkwrench's Avatar
 
Join Date: Aug 2012
Location: Perth, Western Australia
Posts: 2,687
Default Re: 1939 - 1942 brake problems

AS the others have said try bench bleeding the master cylinder and also add speed bleeders to your wheel cylinders your life will be so much easier. How old are your lines?
http://www.speedbleeder.com
__________________
"Came too close to dying to stop living now!"
Talkwrench is offline   Reply With Quote
Old 09-20-2016, 08:14 PM   #6
Bdupes
Junior Member
 
Join Date: Sep 2016
Location: Michigan
Posts: 6
Default Re: 1939 - 1942 brake problems

Sponsored Links (Register now to hide all advertisements)
everything is new on this system, the master has been bench bled.
Bdupes is offline   Reply With Quote
Old 09-20-2016, 09:56 PM   #7
38bill
Senior Member
 
38bill's Avatar
 
Join Date: Apr 2014
Location: Minnesota
Posts: 1,163
Default Re: 1939 - 1942 brake problems

Maybe see if you can find somebody with a power type bleeder. I finally purchased a air powered venturi bleeder and it makes it much easier to bleed, especially when starting from scratch.
38bill is offline   Reply With Quote
Old 09-20-2016, 09:59 PM   #8
Kurt in NJ
Senior Member
 
Kurt in NJ's Avatar
 
Join Date: May 2010
Location: on the Littlefield
Posts: 6,140
Default Re: 1939 - 1942 brake problems

This "new" wheel cylinder---did you take it apart to see if the holes are drilled properly---i have seen the bleeder passage drilled 1/2 way down---no way to get air out, and have seen the "fill" passage drilled behind the travel of the cups

used to have a 39, and a 46, now have A and 36 because they have reliable mechanical brakes

I just replaced wheel cylinders on a 36 Packard, ones from a full page advertizer in Hemmings were made wrong too----had to get them from another place that had 'usa" ones---and they wanted the old original ones back
Kurt in NJ is offline   Reply With Quote
Old 09-20-2016, 10:08 PM   #9
SofaKing
Senior Member
 
SofaKing's Avatar
 
Join Date: Jun 2014
Location: Salt Lake City, Utah
Posts: 756
Default Re: 1939 - 1942 brake problems

Since no one mentioned it yet , if you haven't adjusted all eight shoes individually you may be using pedal throw to compensate for the shoes being too far from the drum.
SofaKing is offline   Reply With Quote
Old 09-21-2016, 11:31 AM   #10
Bdupes
Junior Member
 
Join Date: Sep 2016
Location: Michigan
Posts: 6
Default Re: 1939 - 1942 brake problems

Thanks sofaking. I"ll give that a try. It"s kind of embarrassing it"s such a simple system but I"m stuck on this one. Haven"t worked on this style brake before I"ll let you know how it goes.
Bdupes is offline   Reply With Quote
Old 09-21-2016, 11:53 AM   #11
39topless
Senior Member
 
Join Date: Sep 2013
Posts: 1,027
Default Re: 1939 - 1942 brake problems

Kurt in NJ may be on to something. Did you look at the LF wheel cylinder, while someone pumped the brake pedal, with the drums off, to make sure it was working? The shoes should be moving.
39topless is offline   Reply With Quote
Old 09-21-2016, 12:43 PM   #12
Pamlico
Member
 
Pamlico's Avatar
 
Join Date: May 2010
Location: Eastern North Carolina
Posts: 56
Default Re: 1939 - 1942 brake problems

If the brake hose to that wheel cylinder is old (and rubber) it could be deteriorated internally. This usually (in my experience) shows itself by a sticking wheel when the petal is released.
Pamlico is offline   Reply With Quote
Old 09-21-2016, 12:45 PM   #13
Bdupes
Junior Member
 
Join Date: Sep 2016
Location: Michigan
Posts: 6
Default Re: 1939 - 1942 brake problems

The shoes are moving I'm going to try sofa kings suggestion on the brake adjustments and I'll let you know. Thanks for the input.
Bdupes is offline   Reply With Quote
Old 09-21-2016, 12:47 PM   #14
Bdupes
Junior Member
 
Join Date: Sep 2016
Location: Michigan
Posts: 6
Default Re: 1939 - 1942 brake problems

Pamlico all lines and hoses are new and clean.
Bdupes is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 08:51 AM.