|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
12-10-2019, 08:25 PM | #1 |
Senior Member
Join Date: Aug 2010
Location: McMinnville, TN
Posts: 2,327
|
NEW products available thread
This thread is dedicated to NEW products to the market from various vendors; or recently revived previously discontinued items from various vendors. Out of respect to the thread, lets keep discussion away from this thread..
I'll start by posting a few new to us items at the time of the start of this thread 1937-40 60hp oil pump gears 1942-53 Ford generator adjuster nut and square washer (Cadmium Plated) 1932-34 Dual temp gauge lead to radiator rod clips 1933-41 Ford distributor cap bails (Cadmium plated) 1932 Ford steering wheel (will be fully available 1/20/2020) 1932-48 engine mounting bolts (Cadmium Plated) Last edited by 35fordtn; 12-10-2019 at 10:07 PM. |
12-10-2019, 08:56 PM | #2 |
Senior Member
Join Date: May 2010
Location: Coral Springs FL
Posts: 10,873
|
Re: NEW products available thread
I make these "custom" coil bracket holders when requested.
https://www.fordbarn.com/forum/showt...3+coil+bracket |
Sponsored Links (Register now to hide all advertisements) |
|
12-11-2019, 12:07 AM | #3 |
Senior Member
Join Date: Jan 2018
Posts: 412
|
Re: NEW products available thread
Those dual temp clips were selling for crazy prices. Great item Michael !
|
12-11-2019, 11:22 PM | #4 |
Senior Member
Join Date: Dec 2013
Location: Minnesota, Florida Keys
Posts: 10,260
|
Re: NEW products available thread
In addition to my "Trash Can" condensers, I have available an electronic device that allows just about any current 12 volt negative ground tachometer to be run on a 6 volt positive ground vehicle. It is simple to install and connect and will drive just about any tachometer from a $10 "swap meet special" to a $600 Autometer with memory and playback. These have been extensively tested and have proved accurate and reliable. They have sophisticated circuitry to "clean up" the power anomalies present in vintage vehicle electrical systems. In comes with a comprehensive instruction and installation manual.
Here is a link to a short video of the device in action : https://www.youtube.com/watch?v=TaxpuDkWAqc. Here are pictures on the device mounted on the firewall of my 1951 Ford Club Coupe and a picture of the Sun-Pro tachometer head I have mounted on the steering column. The third picture is of a high-end "Mooneyes" tachometer in a '49 Plymouth using the same device. They are available to board members at $125 plus $8 domestic shipping.You can PM me here or email me at [email protected] if interested. |
12-12-2019, 12:02 AM | #5 |
Senior Member
Join Date: May 2010
Location: Williamsburg, Virginia
Posts: 2,646
|
Re: NEW products available thread
Some pretty cool stuff here - well done!
|
12-12-2019, 07:26 PM | #6 |
Senior Member
Join Date: May 2010
Location: Oregon
Posts: 1,265
|
Re: NEW products available thread
Sponsored Links (Register now to hide all advertisements)
|
12-12-2019, 08:54 PM | #7 | |
Senior Member
Join Date: May 2010
Location: Capital of Corruption , NY
Posts: 810
|
Re: NEW products available thread
Quote:
|
|
12-13-2019, 02:35 AM | #8 |
Senior Member
Join Date: Jul 2019
Location: Southern Oregon
Posts: 782
|
Re: NEW products available thread
I think this link to off set crankshaft grinding would be helpful.
https://www.fordbarn.com/forum/showthread.php?t=269054
__________________
Frank '35 Ford Model 51 '48 Ford F3 '54 Ford Tudor Mainline |
12-13-2019, 04:26 PM | #9 |
Senior Member
Join Date: May 2010
Location: Kerrville, Tx
Posts: 2,768
|
Re: NEW products available thread
A friend had a very very bad experience with Tom Bay.
|
12-14-2019, 04:33 AM | #10 |
Senior Member
Join Date: Dec 2011
Location: Country Victoria Australia
Posts: 130
|
Re: NEW products available thread
Where do we find the 32 steering wheels being manufactured?
|
12-14-2019, 08:20 AM | #11 |
Senior Member
Join Date: May 2010
Location: NJ
Posts: 6,143
|
Re: NEW products available thread
|
12-15-2019, 10:53 AM | #12 |
Senior Member
Join Date: Aug 2010
Location: McMinnville, TN
Posts: 2,327
|
Re: NEW products available thread
A couple more new products that haven’t been available for a long time
1937 passenger car glove box liners (includes the door piece) —— available now 1938-39 glove box liners.——- eta 3-4 weeks |
12-20-2019, 05:34 PM | #13 |
Senior Member
Join Date: May 2010
Location: Oregon
Posts: 1,265
|
Re: NEW products available thread
Just got into production some (fiberglass) garnish moldings. These have the inside flange that goes against the glass.
Doors, 1933 5 Window, Quarter, 1933-34 5 Window, Back window, 1933-34 3 or 5 Window. Karl www.wescottsauto.com |
12-21-2019, 10:50 AM | #14 |
Senior Member
Join Date: May 2010
Location: East Shore of LAKE HOUSTON
Posts: 11,106
|
Re: NEW products available thread
Re-lining and re-furbishing BRAKE DRUM service! How many of you guys have brake drums that have been turned way past the legal (and practical) 0.060" oversize? New FORD drums dried-up long ago, and GOOD, useable drums are very rare IF you do come upon them. I know that I (like a lot of you) have at least a dozen worn-out hub/drum assemblies layin' in a corner that are far beyond any realistic use. Well now there's a service in Illinois that will re-line and refurbish (make look like new) just about any kind of brake drum you can come up with, including the aluminum Buick and Pontiac units. J&G BRAKE DRUM RELINING AND REFURBISHING is the name of this most valuable service.
I almost forgot to mention that these guys also arc brake shoes!! Click the link below! DD https://www.jgrelining.com/ Last edited by V8COOPMAN; 12-21-2019 at 06:44 PM. |
12-21-2019, 01:38 PM | #15 |
Senior Member
Join Date: Apr 2011
Location: Plainview, Texas
Posts: 757
|
Re: NEW products available thread
I wonder if they could reline 33 rear drums?
|
12-21-2019, 06:58 PM | #16 |
Senior Member
Join Date: May 2010
Location: East Shore of LAKE HOUSTON
Posts: 11,106
|
Re: NEW products available thread
I'll bet that's why they included their phone number on their web site. I'd also bet that if you call that number ( (815) 276-2578 ), they would likely tell you "yes"...or "no"! I can't imagine why they couldn't, though. Ain't nothin' that special about a '33 rear drum. Click on THIS link below for pictures of some of the REALLY weird drums they've redone. DD https://www.jgrelining.com/photos |
12-21-2019, 07:17 PM | #17 |
Senior Member
Join Date: Dec 2013
Location: Minnesota, Florida Keys
Posts: 10,260
|
Re: NEW products available thread
From the photos on the site, it looks like they specialize putting new steel liners in aluminum drums. Steel drums are a whole different kettle of fish. You better check. Report back what you find out.
Even if they do, I expect it to be an expensive process. Eight lug Pontiacs are something special. |
12-23-2019, 03:09 PM | #18 |
Senior Member
Join Date: Apr 2011
Location: Plainview, Texas
Posts: 757
|
Re: NEW products available thread
Just got off the phone with this folks, very nice, by the way. Yes, they do reline cast iron 33 ford drums, around $325 to $350 per drum, back to new specs. They also offer shoe arching and rivet/bonded shoes. 4 to 5 week turnaround as of right now.
|
02-19-2020, 07:42 PM | #19 |
Senior Member
Join Date: Aug 2010
Location: McMinnville, TN
Posts: 2,327
|
Re: NEW products available thread
The new 1932 Ford steering wheels mentioned in post #1 are finally here.. They are $379.00
If you are a Early Ford V-8 Club member, the price will be $340.00 Last edited by 35fordtn; 02-19-2020 at 08:37 PM. |
02-19-2020, 08:10 PM | #20 |
Senior Member
Join Date: Nov 2010
Location: Beamsville,Ontario,Canada
Posts: 481
|
Re: NEW products available thread
|
05-05-2020, 12:54 PM | #21 |
Senior Member
Join Date: May 2010
Location: Oregon
Posts: 1,265
|
Re: NEW products available thread
I have a customer looking for an antenna hole plug in the windshield center dowel for a 1939 Convertible. This is different than the closed car that Carpenter makes. Ford show part# 91A-7403456 for 1939 and 1940. I have never seen one.
Regardless, I made a 3D printed (pla plastic) version of what I thought the plug might look like. If anyone has one, or seen one, did I get it close? Also what color should it be? |
05-06-2020, 09:28 AM | #22 |
Senior Member
Join Date: May 2010
Location: Oregon
Posts: 1,265
|
Re: NEW products available thread
Some members have reported not seeing the pix, so I am reposting as an attachment.
|
Sponsored Links (Register now to hide all advertisements) |
|
05-06-2020, 09:32 AM | #23 | |
Senior Member
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
|
Re: NEW products available thread
Quote:
__________________
"I can explain it for you. However, I can't understand it for you". |
|
05-06-2020, 09:35 AM | #24 |
Senior Member
Join Date: May 2010
Location: Wisconsin, USA
Posts: 8,935
|
Re: NEW products available thread
Karl, It appears your customer is doing his best to properly restore his convertible. That being the case, you may want to share with him the fact that the center (interior) windshield molding had NO hole in the top if the car was not equipped with a radio.
__________________
"I can explain it for you. However, I can't understand it for you". |
05-12-2020, 05:02 PM | #25 |
Senior Member
Join Date: Nov 2010
Location: Beamsville,Ontario,Canada
Posts: 481
|
Re: NEW products available thread
Just received my steering wheels today, lightning quick shipping to Canada. The wheels are awesome! Thanks Michael.
|
05-19-2020, 01:56 PM | #26 |
Senior Member
Join Date: May 2010
Location: New Jersey
Posts: 831
|
Re: NEW products available thread
Sponsored Links (Register now to hide all advertisements)
|
05-19-2020, 02:31 PM | #27 |
Senior Member
Join Date: May 2010
Location: Oregon
Posts: 1,265
|
Re: NEW products available thread
We still make them (and have for many years) in silicone bronze, here in Oregon USA, chrome plated.
|
05-19-2020, 07:36 PM | #28 |
Senior Member
Join Date: Aug 2010
Location: McMinnville, TN
Posts: 2,327
|
Re: NEW products available thread
Anyone that hasn't had a chance to thumb through Karl Wescott's (Wescott restyling)'s offerings is really missing out. Many attach the name Wescott with the best Fiberglass products available, and while true It's amazing the other hard to find items he offers that restorers hunt for.
|
05-20-2020, 08:49 AM | #29 |
Senior Member
Join Date: May 2010
Location: New Jersey
Posts: 831
|
Re: NEW products available thread
I do have his wooden header on my '40, fit nice.
|
05-24-2020, 03:24 AM | #30 |
Junior Member
Join Date: Feb 2016
Location: Urenui, New Zealand
Posts: 5
|
Re: NEW products available thread
I make stainless windshields for 37-39 Ford cars and trucks. Also Barrel nose bonnet hinges, stainless Jail Bar bumpers etc. However, I'm in New Zealand....
|
05-26-2020, 10:38 PM | #31 |
Senior Member
Join Date: Aug 2010
Location: McMinnville, TN
Posts: 2,327
|
Re: NEW products available thread
This week I had a itch to have some 35/36 car and 35-39 pickup headlamp nuts made. They are exact as original awaiting plating. Odd size that’s unavailable these days.
Sent from my iPhone using Tapatalk |
05-26-2020, 11:15 PM | #32 |
Senior Member
Join Date: May 2010
Location: southeastern Michigan
Posts: 10,069
|
Re: NEW products available thread
I'm sure that you meant to put one in the photo alongside the original shown.
|
05-26-2020, 11:33 PM | #33 |
Senior Member
Join Date: Aug 2010
Location: McMinnville, TN
Posts: 2,327
|
Re: NEW products available thread
|
05-27-2020, 08:29 AM | #34 |
Senior Member
Join Date: May 2010
Location: southeastern Michigan
Posts: 10,069
|
Re: NEW products available thread
Dumb me; sorry. Of course you were referring to the nuts and not the bolts.
|
05-27-2020, 04:38 PM | #35 |
Senior Member
Join Date: May 2010
Location: Basking Ridge, NJ
Posts: 587
|
Re: NEW products available thread
Dave, Are you loosing your eyesight or just going nuts?
|
09-07-2020, 05:21 PM | #36 |
Senior Member
Join Date: May 2010
Location: Oregon
Posts: 1,265
|
Re: NEW products available thread
While not V8 its close. 1931 Deluxe Roadster stock height top irons. Laser cut steel (stainless main arm), investment cast header block. All made in USA. 1932 in the works.
|
09-07-2020, 06:14 PM | #37 |
Senior Member
Join Date: May 2010
Location: NJ
Posts: 6,143
|
Re: NEW products available thread
|
10-06-2020, 12:30 PM | #38 |
Senior Member
Join Date: May 2010
Location: Oregon
Posts: 1,265
|
Re: NEW products available thread
Hot out of the foundry (well warm maybe), 1935-36 Coupe/Roadster/Cabriolet trunk hinges. Made in USA (Oregon specifically). 304 stainless unpolished. Can be polished, painted, or left as is.
|
10-07-2020, 08:47 AM | #39 | |
Senior Member
Join Date: May 2010
Location: Snohomish,WA
Posts: 1,025
|
Re: NEW products available thread
Quote:
A Much needed reproduction. As with all your castings, they look great! |
|
10-26-2020, 08:32 PM | #40 |
Senior Member
Join Date: Aug 2010
Location: McMinnville, TN
Posts: 2,327
|
Re: NEW products available thread
Just had these made up. 41-48 Hood latch dowels. Made here in Tennessee out of stainless. The cupped washer and spring will be done soon... stainless as well. Pictured is next to a original (excuse my black thumb recently smashed by a hammer) |
10-27-2020, 10:24 AM | #41 |
Senior Member
Join Date: May 2010
Location: NJ
Posts: 6,143
|
Re: NEW products available thread
Looks great, Michael. Every time I see stuff like this, it makes me regret not becoming a machinist.
|
10-27-2020, 10:43 PM | #42 |
Senior Member
Join Date: May 2010
Location: Manawatu, New Zealand
Posts: 1,416
|
Re: NEW products available thread
Michael -Get a small twist drill and rotating it between your fingers bore a hole through the base of your thumb nail above the darkest area . Stop when you get blood . It will allow the blood and pressure to escape from your subungal haematoma and hopefully save your nail -Karl
__________________
Such a fine sight to see-Its a Girl, My Lord, in a Flatbed Ford slowin' down to take a look at me. |
Sponsored Links (Register now to hide all advertisements) |
|
10-28-2020, 01:10 AM | #43 | |
Senior Member
Join Date: May 2010
Location: East Shore of LAKE HOUSTON
Posts: 11,106
|
Re: NEW products available thread
Quote:
|
|
10-28-2020, 02:55 AM | #44 |
Senior Member
Join Date: Aug 2013
Location: rosemead ca.
Posts: 574
|
Re: NEW products available thread
damn those are nice. some really nice work being done here on these pages.
|
10-28-2020, 08:31 AM | #45 |
Senior Member
Join Date: May 2010
Location: New Jersey
Posts: 831
|
Re: NEW products available thread
Man I had a heck of a time finding a good pin, cup, and spring a few years ago. My friend had one on a spare '42 hood he had stored. I wound up trading him for some '49 dash knobs.
|
11-05-2020, 06:11 PM | #46 |
Senior Member
Join Date: Aug 2010
Location: McMinnville, TN
Posts: 2,327
|
Re: NEW products available thread
Sponsored Links (Register now to hide all advertisements)
Sent from my iPhone using Tapatalk |
11-05-2020, 11:34 PM | #47 |
Senior Member
Join Date: Jan 2014
Location: Orcas Island Washington
Posts: 4,846
|
Re: NEW products available thread
You guys are killing me here! Such beautiful parts, and I'm guessing not for huge profits, but as a way to add in part to the legacy of our great vehicles.... And as for McMinville Tennessee, I just finished a complete resto of my powermatic model 66 tablesaw which was made there in 1978. Had to do it over last weekend because during the week I can't earn a dime without it.
__________________
Owner/Operator of 'Jailbar Ranch' on the side of Mt. Pickett. Current stable consists of 1946 1/2 ton pickup turned woodie wagon with FH V8, 1947 Tonner Pickup (red) mostly stock with exception of a cummins 6at turbo diesel, 1946 Tonner Pickup (green) with 226 cu in 6 cyl flathead, 1979 Toyota landcruiser wagon, completely encased in 1947 Ford Jailbar sheet metal. Ok, cornbinder rear fenders..... 'Rusty ol' floorboards, hot on their feet' (Alan Jackson) |
11-05-2020, 11:48 PM | #48 | |
Senior Member
Join Date: Aug 2013
Location: rosemead ca.
Posts: 574
|
Re: NEW products available thread
Quote:
|
|
11-05-2020, 11:59 PM | #49 |
Senior Member
Join Date: May 2015
Posts: 7,926
|
Re: NEW products available thread
__________________
The only thing nice about being imperfect is the joy it brings to others.... "Silver rings, your butt! Them's washers!" "We shot our way out of that town for a dollar's worth of steel holes!" - from 'The Wild Bunch' - 1969 https://www.youtube.com/watch?v=7NReUd2_0u0 |
11-06-2020, 05:38 AM | #50 | |
Senior Member
Join Date: Aug 2010
Location: McMinnville, TN
Posts: 2,327
|
Re: NEW products available thread
Quote:
|
|
11-06-2020, 05:43 AM | #51 | |
Senior Member
Join Date: Aug 2013
Location: rosemead ca.
Posts: 574
|
Re: NEW products available thread
Quote:
|
|
11-06-2020, 05:50 AM | #52 |
Senior Member
Join Date: Aug 2010
Location: McMinnville, TN
Posts: 2,327
|
Re: NEW products available thread
|
11-09-2020, 02:56 PM | #53 |
Senior Member
Join Date: Jun 2011
Location: Australia
Posts: 244
|
Re: NEW products available thread
A new product i have recently made
Flathead V8 finned coolant pipes. [ Fits in between Radiator and heads ] |
11-09-2020, 03:02 PM | #54 | |
Senior Member
Join Date: May 2015
Posts: 7,926
|
Re: NEW products available thread
Quote:
__________________
The only thing nice about being imperfect is the joy it brings to others.... "Silver rings, your butt! Them's washers!" "We shot our way out of that town for a dollar's worth of steel holes!" - from 'The Wild Bunch' - 1969 https://www.youtube.com/watch?v=7NReUd2_0u0 |
|
11-09-2020, 03:04 PM | #55 |
Senior Member
Join Date: May 2010
Location: Oregon
Posts: 1,265
|
Re: NEW products available thread
nice!
|
11-09-2020, 03:19 PM | #56 |
Senior Member
Join Date: Dec 2013
Location: Minnesota, Florida Keys
Posts: 10,260
|
Re: NEW products available thread
Those look nice, but what years are they for? They appear to be too short for '32-'36 and not curved enough for the later models. I would also like to see a set installed.
|
11-09-2020, 04:28 PM | #57 |
Senior Member
Join Date: May 2010
Location: Oshkosh, Wi
Posts: 4,516
|
Re: NEW products available thread
Have some similar in my 39. Use an el and a straight piece of hose to connect to the radiator.
|
11-09-2020, 06:15 PM | #58 |
Senior Member
Join Date: Dec 2010
Location: Tucson, AZ
Posts: 177
|
Re: NEW products available thread
so where are they for sale?
|
11-09-2020, 08:24 PM | #59 |
Senior Member
Join Date: Jun 2011
Location: Australia
Posts: 244
|
Re: NEW products available thread
|
11-09-2020, 08:32 PM | #60 |
Senior Member
Join Date: May 2015
Posts: 7,926
|
Re: NEW products available thread
Old Time Speed > https://www.oldtimespeed.com.au/
Old Time Speed Keith Sutton 0408 289302 [email protected] Terry Wills 0450 566 337 [email protected] USA Distributors Canadian Distributor Jerry Hopkins (903) 875 9557 Don Soenen [email protected] [email protected] (403) 329-3919 Cell (403) 394-6668 SoCal Roadster Supply [email protected] (714) 583-4118 Stanton, Ca 90680
__________________
The only thing nice about being imperfect is the joy it brings to others.... "Silver rings, your butt! Them's washers!" "We shot our way out of that town for a dollar's worth of steel holes!" - from 'The Wild Bunch' - 1969 https://www.youtube.com/watch?v=7NReUd2_0u0 Last edited by petehoovie; 11-09-2020 at 08:40 PM. |
11-10-2020, 02:59 PM | #61 |
Senior Member
Join Date: May 2010
Location: Oregon
Posts: 1,265
|
Re: NEW products available thread
1937 hood latch cam. 78-16628.
Original on right, finished repro in middle, cutout blank on left. I had the cutout blanks laser cut which allows me to hand form and weld up to make the finished part without expensive tooling. |
11-23-2020, 09:12 PM | #62 |
Senior Member
Join Date: Aug 2010
Location: McMinnville, TN
Posts: 2,327
|
Re: NEW products available thread
A simple one; yet one I needed recently. now available 11A-16925 1941-51 Ford hood latch dowel spring.
https://thirdgenauto.com/product/194...-dowel-spring/ IMG_9646_InPixio.jpg |
Sponsored Links (Register now to hide all advertisements) |
|
11-25-2020, 04:44 PM | #63 |
Senior Member
Join Date: Aug 2010
Location: McMinnville, TN
Posts: 2,327
|
Re: NEW products available thread
These won’t be available until middle of February. But for the 32 guys a perfect reproduction of the transmission cover and dual temp gauge face are coming and both will be very very reasonably priced.
Sent from my iPhone using Tapatalk |
11-25-2020, 05:42 PM | #64 |
Senior Member
Join Date: May 2010
Location: Oregon
Posts: 1,265
|
Re: NEW products available thread
Just back from the polisher:
1941-48 convertible visor arms. 304 stainless and polished. The mounting end is modified to use a "C" clip rather than being riveted as original. I have the springs also available. |
11-25-2020, 05:45 PM | #65 |
Senior Member
Join Date: May 2010
Location: Oregon
Posts: 1,265
|
Re: NEW products available thread
Also back from the polisher:
Late 1939-1940 convertible visor arms. 304 stainless and polished. Spring is available. Carpenter had been making these but discontinued them about a year ago. |
11-25-2020, 05:49 PM | #66 |
Senior Member
Join Date: May 2010
Location: Oregon
Posts: 1,265
|
Re: NEW products available thread
Sponsored Links (Register now to hide all advertisements)
Late 1935-1936 Roadster/Phaeton windwing brackets. Investment cast 304 stainless and polished. Kit will include hardware as shown. |
11-25-2020, 06:54 PM | #67 |
Senior Member
Join Date: Aug 2010
Location: McMinnville, TN
Posts: 2,327
|
Re: NEW products available thread
Excellent work Karl!
|
11-25-2020, 07:06 PM | #68 |
Senior Member
Join Date: May 2010
Location: southeastern Michigan
Posts: 10,069
|
Re: NEW products available thread
Karl,
Good show; right down to the correct lock nuts. Will you offer the rubber inserts to retain the glass? |
11-25-2020, 08:22 PM | #69 |
Senior Member
Join Date: May 2010
Location: Oregon
Posts: 1,265
|
Re: NEW products available thread
No rubber inserts at this time, Carpenters are slightly off. There is some emerging technology to 3D print elastic materials at a reasonable price... but not affordable to me yet. The lock nuts are a commercial stainless nylock... that happens to look like the original.
|
11-25-2020, 09:45 PM | #70 |
Senior Member
Join Date: Jan 2018
Posts: 412
|
Re: NEW products available thread
Michael, you have to make the dual temp gauge faces for the 33/34 gauges. I have 6 of them that need face restoring.
|
11-26-2020, 09:14 AM | #71 |
Senior Member
Join Date: Jun 2018
Posts: 134
|
Re: NEW products available thread
I see that you have visor arms, do you have the bracket? I broke mine.
Sent from my SM-G973U using Tapatalk |
11-26-2020, 12:44 PM | #72 | |
Senior Member
Join Date: May 2010
Location: Northridge, CA
Posts: 234
|
Re: NEW products available thread
Quote:
Michael I have about a dozen of the 11A cups that go with your 11A dowel and spring if you are interested. 40larry |
|
12-12-2020, 02:58 PM | #73 |
Member
Join Date: Oct 2016
Posts: 59
|
Re: NEW products available thread
Hello all
Does anyone know where to find the seal for a 1932 Ford Cabriolet header bow? Drake has quit making them. Realized too late that I should have snagged one. Insight appreciated. |
12-12-2020, 11:22 PM | #74 |
Senior Member
Join Date: May 2010
Location: Williamsburg, Virginia
Posts: 2,646
|
Re: NEW products available thread
Check with Drake suppliers - they may have some stock. Try Joe’s Antique Auto Parts. Nice folks to deal with .....
Good luck .... |
12-14-2020, 10:04 PM | #75 |
Senior Member
Join Date: Aug 2010
Location: McMinnville, TN
Posts: 2,327
|
Re: NEW products available thread
Another simple item that is newly available.
Spring shackle bar for 32-40 fords made exact as original, with the correct shape. Sent from my iPhone using Tapatalk |
12-15-2020, 10:42 AM | #76 |
Senior Member
Join Date: Dec 2014
Location: Columbus, IN
Posts: 1,401
|
Re: NEW products available thread
Michael, excellent looking shackle bars. Thank you
|
12-15-2020, 12:10 PM | #77 |
Senior Member
Join Date: May 2010
Location: Northridge, CA
Posts: 234
|
Re: NEW products available thread
|
12-15-2020, 12:17 PM | #78 |
Senior Member
Join Date: May 2010
Location: southeastern Michigan
Posts: 10,069
|
Re: NEW products available thread
The M only appeared on the forged version and only on those supplied by Moore Drop Forgings, which were in a minority of the originals that I've seen, NOS or used.
|
12-15-2020, 03:07 PM | #79 |
Junior Member
Join Date: Jan 2014
Location: buxton maine
Posts: 25
|
Re: NEW products available thread
Can we buy directly from you or eBay only?
|
12-15-2020, 03:13 PM | #80 |
Senior Member
Join Date: Aug 2010
Location: McMinnville, TN
Posts: 2,327
|
Re: NEW products available thread
We sell on ebay, but prices are a bit higher as is shipping on there. Best to call direct, or use thirdgenauto.com
|
12-15-2020, 04:24 PM | #81 | |
Senior Member
Join Date: May 2010
Location: Northridge, CA
Posts: 234
|
Re: NEW products available thread
Quote:
I have about 40 originals here I keep for restorations and they are about 90% with the big M. Most of these have come from 1939 and 1940 cars which I have parted out over the years. I will check those restorations book as I think the V8 club expects to see the M during judging. |
|
12-15-2020, 04:35 PM | #82 |
Senior Member
Join Date: May 2010
Location: Northridge, CA
Posts: 234
|
Re: NEW products available thread
Okay I checked the 1938 1939 Book which states that these shackle bars changed in 1939 to the 91A-5468 and increased the length from 1.50" to 1.56" and they were marked with the M for identification. Most likely the reproduction here is 1.50" and is only correct up through 1938.
|
Sponsored Links (Register now to hide all advertisements) |
|
12-22-2020, 11:17 AM | #83 |
Senior Member
Join Date: Aug 2010
Location: McMinnville, TN
Posts: 2,327
|
Re: NEW products available thread
Another new small item. I only made 200 of these and will not make anymore in the future. B-2075 1932-34 Ford front brake actuating pin. Seems like these become lost frequently.
Sent from my iPhone using Tapatalk |
01-15-2021, 02:04 PM | #84 |
Senior Member
Join Date: Aug 2010
Location: McMinnville, TN
Posts: 2,327
|
Re: NEW products available thread
Another simple and silly but useful new item. A reproduction of the 32-38 KR Wilson synchronizer hub tool. If you’ve rebuilt one of these you know it can be a pain to compress all 6 springs and balls while sliding the hub into the sleeve. With this tool, as you push the hub down it compresses the springs making it a 3 second job. I use my Kr Wilson one all the time. We only made a limited one time run of them. They are zinc plated.
Sent from my iPhone using Tapatalk |
01-15-2021, 04:05 PM | #85 |
Senior Member
Join Date: Dec 2014
Location: Columbus, IN
Posts: 1,401
|
Re: NEW products available thread
Wow, now I can get rid of the popsicle sticks and hose clamps that I used for this job.
|
01-26-2021, 10:51 PM | #86 |
Senior Member
Join Date: Aug 2010
Location: McMinnville, TN
Posts: 2,327
|
Re: NEW products available thread
Sponsored Links (Register now to hide all advertisements)
Sent from my iPhone using Tapatalk |
01-26-2021, 11:40 PM | #87 |
Senior Member
Join Date: Aug 2013
Location: rosemead ca.
Posts: 574
|
Re: NEW products available thread
super nice.
|
03-06-2021, 11:18 AM | #88 |
Senior Member
Join Date: May 2010
Location: Cincinnati, OH
Posts: 1,356
|
Re: NEW products available thread
We just introduced a new item.....the special hardware kit for the Borg Warner overdrive lockout levers. The kit fits all versions of the BW lockout levers. These are the pieces needed to properly clamp the lockout cable to the lever, allowing the lever to rotate without twisting or binding the cable. The special stepped washer and the fine thread bolt (drilled for the wire cable end) are often lost, misplaced, or damaged. You can now buy these pieces, along with the related washers and nut to complete your overdrive transmission installation. Our part number is VP-7689K and is listed in our Overdrive Transmission Parts Prices.
__________________
VANPELT SALES LLC Cincinnati, Ohio Office: 513-724-9486 www.vanpeltsales.com www.classictransmission.com |
03-06-2021, 11:20 AM | #89 | |
Senior Member
Join Date: May 2015
Posts: 7,926
|
Re: NEW products available thread
Quote:
__________________
The only thing nice about being imperfect is the joy it brings to others.... "Silver rings, your butt! Them's washers!" "We shot our way out of that town for a dollar's worth of steel holes!" - from 'The Wild Bunch' - 1969 https://www.youtube.com/watch?v=7NReUd2_0u0 |
|
04-15-2022, 01:50 PM | #90 |
Senior Member
Join Date: May 2010
Location: Oregon
Posts: 1,265
|
Re: NEW products available thread
Just a teaser today. In from the foundry:
Door dovetail for Station Wagons 1928-32 front and rear doors (and 1933-34 rear doors only). Inside door handle for 1932 roadster / phaeton. The importers of the Taiwan ones are sold out and do not expect any for a year or more. Cabriolet top latch handle 1932-36 (when finished will include roller) Cabriolet top latch handle 1937-38 (when finished will include roller) These are all 304 stainless. Next steps are polishing and assembly of the handles. I will post again when finished. |
04-15-2022, 02:34 PM | #91 | |
Senior Member
Join Date: May 2015
Posts: 7,926
|
Re: NEW products available thread
Quote:
__________________
The only thing nice about being imperfect is the joy it brings to others.... "Silver rings, your butt! Them's washers!" "We shot our way out of that town for a dollar's worth of steel holes!" - from 'The Wild Bunch' - 1969 https://www.youtube.com/watch?v=7NReUd2_0u0 |
|
04-16-2022, 09:14 AM | #92 |
Senior Member
Join Date: May 2010
Location: southeastern Michigan
Posts: 10,069
|
Re: NEW products available thread
Karl,
Thanks for creating those items! |
10-20-2022, 10:02 AM | #93 |
Senior Member
Join Date: Aug 2010
Location: McMinnville, TN
Posts: 2,327
|
Re: NEW products available thread
Thought I'd share this. I have been using these on my driver cars as they appear somewhat original compared to the Pete and Jakes etc out there.. Polyurethane shackles that use slotted nuts and original type shackle bars..
https://thirdgenauto.com/product/new...g-shackle-set/ |
12-15-2022, 01:55 PM | #94 |
Senior Member
Join Date: May 2010
Location: Oregon
Posts: 1,265
|
Re: NEW products available thread
1936 Hood latch front catch. "Correct" reproductions from Drake have been unavailable for some time, so I am making these "REPLACEMENT" style without the embossed area. 304 Stainless. Note the hole in the middle is for a rubber bumper.
|
12-15-2022, 02:47 PM | #95 |
Senior Member
Join Date: May 2010
Posts: 2,460
|
Re: NEW products available thread '32 Cabriolet door part
Had these made as a few of us cabriolet restorers needed them. The guide the window mechanisms I believe. Each door needs two, a left and a right. Very limited production. Need correct top pivot bolts, made at one time by "True Blue 32' [deceased now]. PM me Newc
|
12-15-2022, 02:57 PM | #96 |
Senior Member
Join Date: May 2015
Posts: 7,926
|
Re: NEW products available thread
__________________
The only thing nice about being imperfect is the joy it brings to others.... "Silver rings, your butt! Them's washers!" "We shot our way out of that town for a dollar's worth of steel holes!" - from 'The Wild Bunch' - 1969 https://www.youtube.com/watch?v=7NReUd2_0u0 |
12-15-2022, 02:58 PM | #97 | |
Senior Member
Join Date: May 2015
Posts: 7,926
|
Re: NEW products available thread '32 Cabriolet door part
Quote:
__________________
The only thing nice about being imperfect is the joy it brings to others.... "Silver rings, your butt! Them's washers!" "We shot our way out of that town for a dollar's worth of steel holes!" - from 'The Wild Bunch' - 1969 https://www.youtube.com/watch?v=7NReUd2_0u0 |
|
12-15-2022, 09:19 PM | #98 |
Senior Member
Join Date: May 2010
Location: Above the gnat line in Georgia
Posts: 7,009
|
Re: NEW products available thread
I'll bet that's why they included their phone number on their web site. I'd also bet that if you call that number ( (815) 276-2578 ), they would likely tell you "yes"...or "no"!
Coop: Sarcasm is not a virtue. Amen.
__________________
Life is like a roll of toilet paper. The closer to the end, the faster it goes. It is better to be seen, than viewed. "We sleep safe in our beds because rough men stand ready in the night to visit violence on those who would do us harm". |
12-15-2022, 10:13 PM | #99 | |
Senior Member
Join Date: May 2010
Location: East Shore of LAKE HOUSTON
Posts: 11,106
|
Re: NEW products available thread
Quote:
Wow.... you had to go back THREE years for that one. Nevertheless, what you refer to as "sarcasm" is only pointing out what MOST folks either overlook, or find too troublesome to undertake by themselves. Coop . |
|
12-16-2022, 11:34 AM | #100 |
Senior Member
Join Date: May 2010
Location: Napa,California
Posts: 6,007
|
Re: NEW products available thread
Karl, thanks for posting and making the '36 hood catch. Had a young guy ask me about a pair at the Albany Swap Meet. Luckily I kept his phone number and called him back yesterday and sent him your way.
|
01-04-2023, 09:05 PM | #101 |
Senior Member
Join Date: Aug 2010
Location: McMinnville, TN
Posts: 2,327
|
Re: NEW products available thread
A new simple part available now. 1932-40 wishbone ball cap. Will be available on our site Tommorow.
Sent from my iPhone using Tapatalk |
03-08-2023, 08:14 PM | #102 |
Senior Member
Join Date: May 2010
Location: Oregon
Posts: 1,265
|
1928-32 Station Wagon Dovetail (also rear 1933-34)
Station Wagon dovetail, cast stainless, polished
Wescotts Auto |
Sponsored Links (Register now to hide all advertisements) |
|
03-08-2023, 08:28 PM | #103 |
Senior Member
Join Date: Aug 2013
Location: rosemead ca.
Posts: 574
|
Re: NEW products available thread
who will start making 36' bumpers again? so many things i still need/want are now not being made. rear view mirror, sun visor frames, bumpers could be had in chrome or stainless steel. whos got the dies?
|
03-08-2023, 09:37 PM | #104 |
Senior Member
Join Date: Aug 2021
Location: Upstate N.Y.
Posts: 434
|
Re: NEW products available thread
35’ / 36’ 3 Window Coupe Sill Plates / Scuff Plates ?
|
03-08-2023, 09:57 PM | #105 |
Senior Member
Join Date: Aug 2013
Location: rosemead ca.
Posts: 574
|
Re: NEW products available thread
|
06-08-2023, 05:31 PM | #106 |
Senior Member
Join Date: Aug 2010
Location: McMinnville, TN
Posts: 2,327
|
Re: NEW products available thread
Sponsored Links (Register now to hide all advertisements)
https://thirdgenauto.com/product/new...h-release-arm/ |
06-08-2023, 06:35 PM | #107 |
Senior Member
Join Date: May 2010
Posts: 191
|
Re: NEW products available thread
How about some 1938/39 woodie rear seat legs? I can't find them any where.
These are shorter size ( About 2" tall) |
06-08-2023, 06:49 PM | #108 | |
Senior Member
Join Date: May 2010
Location: NJ
Posts: 6,143
|
Re: NEW products available thread
Quote:
|
|
02-13-2024, 04:05 PM | #109 |
Senior Member
Join Date: Nov 2020
Location: SW WA
Posts: 639
|
Re: NEW products available thread
Coming soon… 1935-1939 steering column tubes. I will have these available for both passenger cars as well as pickups. I am making these from a thicker 18 gauge tubing rather than the factory used 20g. Harder to dent, harder to bend. The bottom end of the tube is bored out in order for the thicker tube to fit over the steering box. The top is flared with the exact same profile as the factory tubes. I have made 12 of each and wanted to offer them to Barn members first.
Please PM me for more information or contact me thru www.nwclassicparts.com. Thanks! Last edited by OldGold360; 02-13-2024 at 04:14 PM. |
02-13-2024, 06:46 PM | #110 | |
Senior Member
Join Date: May 2015
Posts: 7,926
|
Re: NEW products available thread
Quote:
__________________
The only thing nice about being imperfect is the joy it brings to others.... "Silver rings, your butt! Them's washers!" "We shot our way out of that town for a dollar's worth of steel holes!" - from 'The Wild Bunch' - 1969 https://www.youtube.com/watch?v=7NReUd2_0u0 |
|
02-13-2024, 07:14 PM | #111 |
Senior Member
Join Date: Aug 2013
Location: rosemead ca.
Posts: 574
|
Re: NEW products available thread
does anybody know what happened to the 35-36 bumper supplier? someone has to have the dies to make more. no one has any. i need a pair for my project.
|
02-13-2024, 11:11 PM | #112 |
Senior Member
Join Date: May 2010
Posts: 2,460
|
Re: NEW products available thread
Greg Edwards made 6 of the '32 car steering tubes correctly- Very expensive and sloow selling. I found the correct steel in a 20ft length. Never again. Newc
|
02-13-2024, 11:26 PM | #113 |
Senior Member
Join Date: May 2010
Posts: 420
|
Re: NEW products available thread
[
Precision-engineered stone guards designed for 1946-1948 Ford Woodie, meticulously crafted through cutting-edge 3D printing technology. Surpassing the performance of original and now unavailable vulcanized reproductions, these guards offer enhanced durability without the risk of steel rusting. Designed with integrated "studs," these guards ensure easy and secure mounting. Alternatively, they can be attached using a variety of adhesive options for added flexibility. Expected to be available in June 2024, exclusively on demand!
__________________
Pennsylvania has two seasons. Hershey week, and everything else https://sites.google.com/site/eastcoastwoodies/ Last edited by sawzall; 02-13-2024 at 11:32 PM. |
02-14-2024, 02:22 AM | #114 | |
Senior Member
Join Date: Nov 2020
Location: SW WA
Posts: 639
|
Re: NEW products available thread
Quote:
Dale, Thank you for clarifying what you meant in your post. That was my fault for misunderstanding what you said. Last edited by OldGold360; 02-14-2024 at 05:24 PM. |
|
02-14-2024, 09:16 AM | #115 |
Senior Member
Join Date: May 2010
Location: Coral Springs FL
Posts: 10,873
|
Re: NEW products available thread
THANK YOU to all those who spend the $, time, effort and knowledge to make all the repro. parts shown in this thread.
|
02-14-2024, 12:01 PM | #116 |
Senior Member
Join Date: May 2010
Posts: 2,460
|
Re: NEW products available thread
'32 Cabriolet top iron PIVOT bolts. Made with Stainless Steel. One time only-two sets [6 bolts] left [$95 shipped]. Paypal/MO Newc
|
02-14-2024, 12:21 PM | #117 |
Senior Member
Join Date: May 2015
Posts: 7,926
|
Re: NEW products available thread
__________________
The only thing nice about being imperfect is the joy it brings to others.... "Silver rings, your butt! Them's washers!" "We shot our way out of that town for a dollar's worth of steel holes!" - from 'The Wild Bunch' - 1969 https://www.youtube.com/watch?v=7NReUd2_0u0 |
02-14-2024, 05:25 PM | #118 |
Senior Member
Join Date: Nov 2020
Location: SW WA
Posts: 639
|
Re: NEW products available thread
|
02-14-2024, 05:27 PM | #119 |
Senior Member
Join Date: May 2010
Location: southeastern Michigan
Posts: 10,069
|
Re: NEW products available thread
They are better than nice.
|
02-14-2024, 05:42 PM | #120 |
Senior Member
Join Date: Nov 2020
Location: SW WA
Posts: 639
|
Re: NEW products available thread
|
02-14-2024, 07:01 PM | #121 |
Senior Member
Join Date: May 2010
Location: Basking Ridge, NJ
Posts: 587
|
Re: NEW products available thread
Yipes, is that semantics or grammer that invaded a compliment ?
|
02-15-2024, 02:52 PM | #122 |
Senior Member
Join Date: May 2010
Location: NJ
Posts: 6,143
|
Re: NEW products available thread
|
Sponsored Links (Register now to hide all advertisements) |
|
Thread Tools | |
Display Modes | |
|
|
Sponsored Links (Register now to hide all advertisements) |
|