11-23-2018, 02:21 AM | #1 |
Senior Member
Join Date: Nov 2016
Posts: 279
|
door locks
hello everybody
i must to change the door locks in my 56 customline does anyone knows how to change door locks cylinder? thanks for the answer |
11-23-2018, 09:25 AM | #2 |
Senior Member
Join Date: Dec 2011
Location: Oakville Ontario
Posts: 586
|
Re: door locks
once you remove door panel you will see a clip holding the lock.the clip slides on to the lock from the door edge it will be behind the rubber seal.the seal should not be glued to door where clip is unless someone glued it when replacing the seal.if glued carefully trim glue from door taking care not to break-cut seal.clip can be hard to remove using a large bladed screwdriver will help.make note of the linkage position when removing from old cylinder.
|
Sponsored Links (Register now to hide all advertisements) |
|
11-24-2018, 03:12 AM | #3 |
Senior Member
Join Date: Nov 2016
Posts: 279
|
Re: door locks
does anyone have a pic of the system door lock?
|
11-24-2018, 12:04 PM | #4 |
Senior Member
Join Date: Nov 2016
Location: Now on the Land of Sun City West, AZ
Posts: 416
|
Re: door locks
Have you removed the door lock yet? Don't need to pull pull door panel. Door open push aside weather strip and pull sliding flat pin. Lock will come off door. When reinstalling, put a gasket on it if it was missing....like mine. Gasket seals out water from outside of car. Rekeying? Small screwdriver pry off small top cover on cylinder, over a towel with plenty of light. A spring pops out and then a pin. The length of pins match the new key upon Assy. You need differing lengths of pins and I canibalized other door cylinders to match mine. Make sure spring/pin cover firmly fits on cylinder...
|
11-25-2018, 01:16 PM | #5 |
Senior Member
Join Date: Nov 2016
Posts: 279
|
Re: door locks
i changed the doors locks cylinder it's ok,
but i lost one little sping of lever do you know where can i find it ? |
11-25-2018, 02:54 PM | #6 |
Senior Member
Join Date: Feb 2011
Location: SW WA state.
Posts: 564
|
Re: door locks
Sponsored Links (Register now to hide all advertisements)
__________________
1956 Ford Fairlane Town Sedan 292 V8 with Ford-o-Matic |
11-25-2018, 11:22 PM | #7 |
Senior Member
Join Date: Nov 2016
Location: Now on the Land of Sun City West, AZ
Posts: 416
|
Re: door locks
The spring for the key cover lid?
Agree above, I found one key lock part in the bottom of my door....who knows how long it was there. As a side note, I found rags, a tac rag and a paint stirring stick inside my 1/4 sheet metal! Just great work, sarc/ off. |
11-26-2018, 02:34 AM | #8 |
Senior Member
Join Date: Nov 2016
Posts: 279
|
Re: door locks
no ,the little spring of lever
|
11-26-2018, 12:12 PM | #9 |
Senior Member
Join Date: Nov 2016
Location: Now on the Land of Sun City West, AZ
Posts: 416
|
Re: door locks
Buy the piece from MAC's or other aftermarket part sources.
|
05-15-2024, 08:41 AM | #10 |
Junior Member
Join Date: Apr 2024
Posts: 16
|
Re: door locks
anyone know where i can find the linkage rods for a 1967 galaxie driverside door lock?
|
|
|
Sponsored Links (Register now to hide all advertisements) |
|