The Ford Barn

mike kilger · 03-07-2012, 08:29 PM

any one make one that fits a 34 rear end, Is model A the same center??

Elmo Rodge · 03-07-2012, 08:38 PM

Mike, my first call would be to Nick and Ken Smith at Hot Rod Works. They should know. 208 463 1068 They're in Idaho and Landspeed Racers. Not to mention good Humans. Wayno

uncle buck · 03-07-2012, 09:55 PM

You can also contact Dick Spadaro here on the barn. He sells a Winters version and can offer great advice.

mike kilger · 03-07-2012, 11:03 PM

Thanks Wayne, I will call them.

Bassman/NZ · 03-08-2012, 03:21 AM

Or PM Quickchange over in the model A section. He makes the Model A Kiwi q/c's and I know he's heading to the US in a couple of weeks.

itslow · 03-08-2012, 12:33 PM

Sponsored Links (Register now to hide all advertisements)

Your axle housings will fit on the "V8" size quickchanges, such as the Halibrand 201, but they'll be "clocked" wrong due to the change in bolt pattern orientation in '35, and will wind up being slightly wider due to the increase in center section width. The "V8" quickchanges are intended to be used with the '35+ parts.

The "A" quickchanges, such as the Halibrand 101, are too small and internally different. It will not work and is best left for use in an A.

Given the number of other modifications required to run a quickchange in a '34, you're better off just starting with the components from a later rearend and modifying as necessary.

mike kilger · 03-09-2012, 10:35 AM

well I lnow what I have ti do now , anyway thanks for all the info

03-07-2012, 08:29 PM	#1
mike kilger BANNED Join Date: Jun 2010 Location: riverside ca Posts: 218	34 quick change any one make one that fits a 34 rear end, Is model A the same center??

03-07-2012, 08:38 PM	#2
Elmo Rodge Senior Member Join Date: May 2010 Location: Salina, Utah Posts: 327	Re: 34 quick change Mike, my first call would be to Nick and Ken Smith at Hot Rod Works. They should know. 208 463 1068 They're in Idaho and Landspeed Racers. Not to mention good Humans. Wayno __________________ Life is not a spectator sport.

03-07-2012, 09:55 PM	#3
uncle buck Senior Member Join Date: May 2010 Location: Snohomish,WA Posts: 1,031	Re: 34 quick change You can also contact Dick Spadaro here on the barn. He sells a Winters version and can offer great advice.

03-07-2012, 11:03 PM	#4
mike kilger BANNED Join Date: Jun 2010 Location: riverside ca Posts: 218	Re: 34 quick change Thanks Wayne, I will call them.

03-08-2012, 03:21 AM	#5
Bassman/NZ Senior Member Join Date: May 2010 Location: Napier, New Zealand Posts: 2,001	Re: 34 quick change Or PM Quickchange over in the model A section. He makes the Model A Kiwi q/c's and I know he's heading to the US in a couple of weeks.

03-08-2012, 12:33 PM	#6
itslow Senior Member Join Date: May 2010 Location: Central Iowa Posts: 693	Re: 34 quick change Sponsored Links (Register now to hide all advertisements) Your axle housings will fit on the "V8" size quickchanges, such as the Halibrand 201, but they'll be "clocked" wrong due to the change in bolt pattern orientation in '35, and will wind up being slightly wider due to the increase in center section width. The "V8" quickchanges are intended to be used with the '35+ parts. The "A" quickchanges, such as the Halibrand 101, are too small and internally different. It will not work and is best left for use in an A. Given the number of other modifications required to run a quickchange in a '34, you're better off just starting with the components from a later rearend and modifying as necessary. __________________ Mike Wanted: - '32-34 Open Cab Pickup (RPU) parts and documents/articles/info - ARDUN parts

03-09-2012, 10:35 AM	#7
mike kilger BANNED Join Date: Jun 2010 Location: riverside ca Posts: 218	Re: 34 quick change well I lnow what I have ti do now , anyway thanks for all the info