|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
06-07-2021, 02:06 PM | #1 |
Senior Member
Join Date: Jun 2010
Location: Sioux City Iowa
Posts: 196
|
What sealant to use on rear main bearing cap bolts and shims?
What is the recommended sealant to use on the rear main bearing cap bolts and shims? The engine is in the frame and the crankshaft is counter balanced so removal of the bearing cap is difficult. The oil leak is down from a stream to a drip at fast idle. I am going to remove the pan one more time since I over torqued the pan bolts, as per the Les Andrews book misprint, and replace the pan gasket with another new composite gasket. This is the same engine I have recently made posts about on here if you are following along with my exploits. I am gaining on the problems, not much though it seems. Thanks to all for the excellent advice!
|
06-07-2021, 03:46 PM | #2 |
Senior Member
Join Date: May 2010
Location: Largo Florida
Posts: 7,225
|
Re: What sealant to use on rear main bearing cap bolts and shims?
I use nothing.
|
Sponsored Links (Register now to hide all advertisements) |
|
06-07-2021, 04:00 PM | #3 |
Senior Member
Join Date: May 2010
Location: Eastern Tennessee
Posts: 11,516
|
Re: What sealant to use on rear main bearing cap bolts and shims?
Yes, we do not use anything.
If the block and the caps were machined properly during rebuilding, they will easily compress the shims to seal un-pressurized oil from escaping. |
06-09-2021, 06:26 PM | #4 |
Senior Member
Join Date: Aug 2010
Location: SF Bay Area
Posts: 193
|
Re: What sealant to use on rear main bearing cap bolts and shims?
Are you certain the leak is from the rear main cap and not the rear cam bearing?
|
06-09-2021, 08:11 PM | #5 |
Senior Member
Join Date: May 2010
Location: Largo Florida
Posts: 7,225
|
Re: What sealant to use on rear main bearing cap bolts and shims?
If you're removing the pan again, you might want to make sure of the rear bearing clearance. I like to run all of them at .0015" and the rear main just a bit tighter.
And, what Dan said. |
06-09-2021, 09:18 PM | #6 |
BANNED
Join Date: Dec 2019
Posts: 1,196
|
Re: What sealant to use on rear main bearing cap bolts and shims?
Sponsored Links (Register now to hide all advertisements)
|
06-09-2021, 09:59 PM | #7 |
Senior Member
Join Date: Jun 2010
Location: Sioux City Iowa
Posts: 196
|
Re: What sealant to use on rear main bearing cap bolts and shims?
It is not leaking from the rear of the cam shaft. I went back together with nothing on the shims or bolts. I took out 1 peel shim on each side, .002, buttoned it all up except for the dust cover and ran it for about 10 minutes. Dry as can be! Rated right up there on the excitement scale with first time engine start from total rebuild. Adjusted the brakes last night and will be doing a carb. rebuild this weekend and front wheel bearing repack as well. It's getting close, the owner is getting anxious to drive it again. Thanks everybody for the great input, my local go to Model A guy has failing health, so I'll be back with more questions.
|
06-09-2021, 10:08 PM | #8 |
Senior Member
Join Date: Apr 2015
Location: Saint Cloud Mn
Posts: 745
|
Re: What sealant to use on rear main bearing cap bolts and shims?
If you are using RTV you are doing something wrong.
|
06-09-2021, 11:09 PM | #9 |
Senior Member
Join Date: Dec 2010
Location: Verdi, Nevada
Posts: 166
|
Re: What sealant to use on rear main bearing cap bolts and shims?
Go to Antique Engine Rebuilding Website. Rich gives the total how to etc. on rear main bearing installation/troubleshooting.. bottom line is that the bearing cap surface has to perfectly match the block surface..
|
06-10-2021, 12:43 AM | #10 |
Senior Member
Join Date: May 2010
Location: Portland OR
Posts: 6,341
|
Re: What sealant to use on rear main bearing cap bolts and shims?
We put a little RTV sealer between the cork and where it meets the gasket in the chorner only and sometimes a little anarobic between the cap shims and block. Anarobic is thin enough that it should not change the clearance.
__________________
I know the voices aren't real but damn they have some good ideas! |
|
|
Sponsored Links (Register now to hide all advertisements) |
|