|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
12-09-2017, 06:18 PM | #1 |
Senior Member
Join Date: Oct 2015
Location: Bay City Michigan
Posts: 1,050
|
is the throw out bearing supposed to have play?
im cleaning the engine bay to weld the cross member and paint what i can get too while the engine is out. And i look at the throw out bearing and give it a shake there is enough play to make it click is this ok?
|
12-09-2017, 06:56 PM | #2 |
Senior Member
Join Date: May 2010
Posts: 332
|
Re: is the throw out bearing supposed to have play?
If it makes any kind of noise I would recommend changing it and the small bering in the flywheel . Now is the best time to do this job .
|
Sponsored Links (Register now to hide all advertisements) |
|
12-09-2017, 08:06 PM | #3 |
Senior Member
Join Date: Dec 2010
Location: FRESNO, CA
Posts: 12,560
|
Re: is the throw out bearing supposed to have play?
Even if you replace the bearings, re-pack them with a Wheel Bearing Packer. The grease they pack them with is almost like VASELINE!
Bill Practical
__________________
"THE ASSISTANT GURU OF STUFF" |
12-09-2017, 08:19 PM | #4 |
Senior Member
Join Date: May 2010
Location: Eastern CT
Posts: 2,732
|
Re: is the throw out bearing supposed to have play?
I never use a bearing in the flywheel. The original were open bearings and got gunked up with clutch material and seized, ruining the input shaft. The new replacements are sealed, and the seals are so tight that the shaft spins in the bearing and the bearing does not spin. I use a bronze bushing, like Ford did in later years. If a bushing is good enough for a 427 with 4 speed, it is plenty good enough for a model A. the correct bushing can be gotten at NAPA and other auto retailers.
|
12-09-2017, 10:15 PM | #5 | |
Senior Member
Join Date: Mar 2017
Location: southern California
Posts: 725
|
Re: is the throw out bearing supposed to have play?
Quote:
Many folks are concerned about lubricant in the plain bearings (bushings), but the right ones are oil impregnated, so lubrication is not a problem.
__________________
"That's my wild unsubstantiated guess, and I'm sticking to it regardless of the facts!" |
|
12-10-2017, 09:31 AM | #6 |
Senior Member
Join Date: May 2010
Location: ca.
Posts: 2,522
|
Re: is the throw out bearing supposed to have play?
Sponsored Links (Register now to hide all advertisements)
__________________
V4f |
12-10-2017, 12:33 PM | #7 |
Senior Member
Join Date: Dec 2011
Location: SW Idaho
Posts: 970
|
Re: is the throw out bearing supposed to have play?
Off track fellas. T/O bearing and not Pilot bearing. I like the older bearings that have a hole at the inner diameter for the grease to enter the bearing and not just lube the bearing retainer sleeve. The new stuff I've seen have been sealed and would be difficult to even hand pack.
|
12-10-2017, 12:54 PM | #8 |
Senior Member
Join Date: Oct 2015
Location: Bay City Michigan
Posts: 1,050
|
Re: is the throw out bearing supposed to have play?
I looked around And macs had a bronze bushing listed for early v8s 32 trucks and on for 9$. Would that one be a fit? Napa has abandoned my area. There is a auto value affiliated owner operated parts shop ill go to with my mics and the bearing.
On the throw out bearing I'll have to get a new one. https://www.macsautoparts.com/store/...Product_Viewed |
12-10-2017, 03:16 PM | #9 | |
Senior Member
Join Date: May 2010
Location: Eastern CT
Posts: 2,732
|
Re: is the throw out bearing supposed to have play?
Quote:
|
|
|
|
Sponsored Links (Register now to hide all advertisements) |
|