Go Back   The Ford Barn > General Discussion > Late V8 (1954+)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 07-12-2019, 09:48 AM   #1
jsprengeler
Member
 
Join Date: May 2013
Location: Eau Claire, WI
Posts: 42
Default Carb Spacer

Does anyone know where, if anywhere, I can find a 2 bbl carb spacer for the 272 y block in my 55 Ford? Is it possible to make one? I'm looking for one of these to hopefully reduce some vapor locking. Thanks!
__________________
If you haven't screwed things up, you haven't done anything at all!
jsprengeler is offline   Reply With Quote
Old 07-12-2019, 10:42 AM   #2
Hot Rod Reverend
Senior Member
 
Hot Rod Reverend's Avatar
 
Join Date: May 2010
Location: Loveland, Ohio
Posts: 915
Default Re: Carb Spacer

check out this link:

https://www.speedwaymotors.com/Strom...acer,5638.html

not sure if this is what you want to pay but this is what you need IMO.
__________________
Lancaster, California
Visit hotrodreverend.com to view hundreds of pictures and videos of the build of the 1955 Ford Club Sedan!
Hot Rod Reverend is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 07-12-2019, 11:09 AM   #3
fordrodsteven
Member
 
fordrodsteven's Avatar
 
Join Date: Aug 2017
Posts: 66
Default Re: Carb Spacer

Quote:
Originally Posted by jsprengeler View Post
Does anyone know where, if anywhere, I can find a 2 bbl carb spacer for the 272 y block in my 55 Ford? Is it possible to make one? I'm looking for one of these to hopefully reduce some vapor locking. Thanks!
If you decide to make one. you should use the gasket as your template for cutting the holes into the new, thicker material. I don't know what materials, tools you have available. Personally, I would use aluminum to make a plate. You will need to be sure to get the bores nice and smooth or it could disrupt the air / fuel flow into the manifold.
fordrodsteven is offline   Reply With Quote
Old 07-12-2019, 11:52 AM   #4
scicala
Senior Member
 
scicala's Avatar
 
Join Date: Jun 2010
Location: Detroit suburb, MI
Posts: 3,697
Default Re: Carb Spacer

I would buy one of the phenolic ones like hot rod reverend showed you. They transfer way less heat than aluminum to the carb. Also, if you really have vapor lock, it isn't a condition caused by the carb. It's heat in the fuel line or fuel pump that vaporizes the fuel and causes it to not flow.
The carb spacer will help eliminate fuel boiling in the carb after the engine is shut off hot.


Sal
scicala is offline   Reply With Quote
Old 07-12-2019, 12:40 PM   #5
Bob-93021
Member
 
Bob-93021's Avatar
 
Join Date: May 2016
Location: Moorpark, CA
Posts: 72
Default Re: Carb Spacer

I agree that the phenolic spacer would be a good option. I had to make one 40 years ago for my 55 so that I could add a PCV system to meet CA emissions. I do not remember all the details but I made a slot in the spacer and smashed down maybe a 3/8 piece of copper tubing to connect to.

There is a specialize vendor that advertises in the Early Ford V8 magazine that sells a 1/2" thick phenolic spacer, 2 gaskets and longer studs for $30ppd. He can be reached at [email protected]. His name is Robert Schuman. If you do not have a PCV system in your car this spacer could be reworked to include a fitting to connect to.
Bob-93021 is offline   Reply With Quote
Old 07-12-2019, 10:34 PM   #6
wellcraft17
Senior Member
 
Join Date: Feb 2012
Location: Tampa fl
Posts: 130
Default Re: Carb Spacer

Sponsored Links (Register now to hide all advertisements)
This has woken up the old memory bank, I use to make spacers and adapters out of hard wood, ash and red oak, in shop class back in the 60s. They worked great until I got out of school, employed and could afford the real thing.
wellcraft17 is offline   Reply With Quote
Old 07-12-2019, 10:47 PM   #7
1ton
Senior Member
 
Join Date: Jun 2012
Location: North Aurora,Il.
Posts: 154
Default Re: Carb Spacer

Could be a fuel pump problem. I was recently having a vapor lock problem with a 77 chevy truck with a 400 small block and a good rebuilt quadrajet. Kept seeing online that the fuel pump could be weak so I replaced mine with new and , wow, what a difference. That changed how the truck runs dramatically. If you need a spacer made, I can machine one for you.
1ton is offline   Reply With Quote
Old 07-13-2019, 10:47 AM   #8
jsprengeler
Member
 
Join Date: May 2013
Location: Eau Claire, WI
Posts: 42
Default Re: Carb Spacer

Thanks everyone. I do plan to either insulate the fuel lines or replace them with a braided line. My 272 runs fantastic. I just ran into a vapor lock problem the other night when I took my 55 to a local cruise in, and it wouldn’t start when it was time to leave. It was a very hot evening, and the carb wasn’t getting any gas. Several hours later, it started right up. Vapor lock was the obvious problem.
__________________
If you haven't screwed things up, you haven't done anything at all!
jsprengeler is offline   Reply With Quote
Old 07-13-2019, 01:57 PM   #9
19Fordy
Senior Member
 
19Fordy's Avatar
 
Join Date: May 2010
Location: Coral Springs FL
Posts: 10,872
Default Re: Carb Spacer

Why not install an electric fuel pump? That will solve the problem.
19Fordy is offline   Reply With Quote
Old 07-13-2019, 07:56 PM   #10
Ole Don
Senior Member
 
Ole Don's Avatar
 
Join Date: May 2010
Location: St. Michael, Minnesota
Posts: 1,713
Default Re: Carb Spacer

Be sure the heat riser is not stuck closed. A wood spacer works fine, don't slam the hood on the air cleaner wing nut.
Ole Don is offline   Reply With Quote
Old 07-13-2019, 10:30 PM   #11
miker98038
Senior Member
 
miker98038's Avatar
 
Join Date: Mar 2013
Location: Kent, WA. Tucson, AZ
Posts: 1,373
Default Re: Carb Spacer

That happened all the time on my bird. I finally figured out that at a show where I opened the hood, the car started right up. So I open the hood when I park in the garage. I blame ethanol fuel for most of it.
miker98038 is offline   Reply With Quote
Old 07-13-2019, 10:44 PM   #12
Daves55Sedan
Senior Member
 
Daves55Sedan's Avatar
 
Join Date: May 2010
Location: Granite City, Illinois
Posts: 3,008
Default Re: Carb Spacer

I made two of them many decades ago out of thick phenolic material. Still using one in my '55 Y-block with Ford EBU carb. The other one has never been used.
Don't remember where I got the material. Used a hole-saw in a standard 3/8" drill two cut out the two venture holes and a regular steel drill-bit in a drill-press (to make sure the holes were perfectly perpendicular to the intake mounting surface). Used an old carb gasket as a pattern.
If worse comes to worse, contact me by private message here and I can send you my un-used spacer.
You will need longer carb mounting studs, available at many hardware stores.
PS; are you sure the gas is not draining out thru your accelerator pump rather than vapor locking???
Daves55Sedan is offline   Reply With Quote
Old 07-15-2019, 07:32 AM   #13
jsprengeler
Member
 
Join Date: May 2013
Location: Eau Claire, WI
Posts: 42
Default Re: Carb Spacer

Thanks to everyone for your help and expertise! Love this site....
__________________
If you haven't screwed things up, you haven't done anything at all!
jsprengeler is offline   Reply With Quote
Old 07-15-2019, 08:26 AM   #14
Hot Rod Reverend
Senior Member
 
Hot Rod Reverend's Avatar
 
Join Date: May 2010
Location: Loveland, Ohio
Posts: 915
Default Re: Carb Spacer

Quote:
Originally Posted by miker98038 View Post
That happened all the time on my bird. I finally figured out that at a show where I opened the hood, the car started right up. So I open the hood when I park in the garage. I blame ethanol fuel for most of it.
I think Miker is right on the money here... I have experienced the same with Ethanol fuel because of the boiling point being so much lower. Check out a post on my website that I just wrote:
https://www.hotrodreverend.com/singl...with-the-Devil
__________________
Lancaster, California
Visit hotrodreverend.com to view hundreds of pictures and videos of the build of the 1955 Ford Club Sedan!
Hot Rod Reverend is offline   Reply With Quote
Old 07-15-2019, 01:54 PM   #15
50fordcoupeman
Senior Member
 
50fordcoupeman's Avatar
 
Join Date: Mar 2016
Location: LaGrande Oregon
Posts: 865
Default Re: Carb Spacer

Quote:
Originally Posted by Hot Rod Reverend View Post
I think Miker is right on the money here... I have experienced the same with Ethanol fuel because of the boiling point being so much lower. Check out a post on my website that I just wrote:
https://www.hotrodreverend.com/singl...with-the-Devil
Thank you for your ministry passion!! My avatar runs a 302. I always run non ethanol in it and all my stuff that has a carb. Costs a little more but NEVER any fuel related problems. Should not be a question whether or not to use it IMHO.
50fordcoupeman is offline   Reply With Quote
Old 07-18-2019, 01:25 PM   #16
bobss396
Senior Member
 
bobss396's Avatar
 
Join Date: Aug 2014
Posts: 721
Default Re: Carb Spacer

I used to make them out of phenolic for the stock cars, we stocked it at work in 1" sheets. Mills very easily, but can't beat to buy one for $20 and be done with it.
bobss396 is offline   Reply With Quote
Old 07-18-2019, 03:43 PM   #17
KULTULZ
Senior Member
 
KULTULZ's Avatar
 
Join Date: Aug 2012
Location: IN A 'GALAXIE' FAR FAR AWAY
Posts: 6,413
Question Re: Carb Spacer

Quote:
I use to make spacers and adapters out of hard wood

WOOD one need an annual inspection and certificate issued?

__________________
*****

- DISCLAIMER -

The above posted information is in my opinion only (IMO) and may contain copy and paste material(s).

In addition, any above tech information is supplied in good faith. No responsibility implied or otherwise can be accepted for the way others use or interpret provided data.

Your experience(s), opinion(s) and mileage may vary.

DIAGNOSED CDO - (OCD In Correct Alphabetical Order)
KULTULZ is offline   Reply With Quote
Old 07-18-2019, 03:49 PM   #18
KULTULZ
Senior Member
 
KULTULZ's Avatar
 
Join Date: Aug 2012
Location: IN A 'GALAXIE' FAR FAR AWAY
Posts: 6,413
Default Re: Carb Spacer

Quote:
I blame ethanol fuel for most of it.

The same problem(s) existed well before Ethanol Blended Gasolines ...

The main problem with the 55/57 BIRD is stuffing 10# of engine in a 5# bag. That and FORD's design of the cooling system.
Attached Images
File Type: jpg Gasoline Hot Soak - ShopTips NOV 63 #10.jpg (21.6 KB, 7 views)
__________________
*****

- DISCLAIMER -

The above posted information is in my opinion only (IMO) and may contain copy and paste material(s).

In addition, any above tech information is supplied in good faith. No responsibility implied or otherwise can be accepted for the way others use or interpret provided data.

Your experience(s), opinion(s) and mileage may vary.

DIAGNOSED CDO - (OCD In Correct Alphabetical Order)
KULTULZ is offline   Reply With Quote
Old 07-18-2019, 06:21 PM   #19
dmsfrr
Senior Member
 
dmsfrr's Avatar
 
Join Date: Aug 2012
Location: Abq, NM
Posts: 3,598
Default Re: Carb Spacer

Quote:
Originally Posted by KULTULZ View Post
...
The main problem with the 55/57 BIRD is stuffing 10# of engine in a 5# bag. That and FORD's design of the cooling system.
Along with rust debris buildup in the coolant passages toward the rear of the block...
(see photos, bottom of the page at this link)
https://www.ctci.org/gilsgarage/Overheating.php

... the design of the T-bird water pump spacer left a fair amount to be desired.
A fellow named Chris Ames has recently redesigned and improved it, with very good results.
(photos at this link)
https://thunderbird.us/
.

Last edited by dmsfrr; 07-18-2019 at 07:06 PM.
dmsfrr is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 08:22 AM.