|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
06-05-2021, 07:44 PM | #1 |
Senior Member
Join Date: May 2010
Location: Kerrville, Tx
Posts: 2,769
|
32 brake lever sector dimension
I would like to modify a Model A brake lever sector to use on a 32. The A part has the pivot hole 1.75” below a line thru the mounting holes. I need the dimension for a 32. Thanks!
Last edited by Andy; 06-05-2021 at 07:53 PM. |
06-05-2021, 08:24 PM | #2 |
Senior Member
Join Date: May 2010
Location: southeastern Michigan
Posts: 10,096
|
Re: 32 brake lever sector dimension
See post #8 in the thread "32 emergency brake lever" further down the first page in this forum showing the Model A and '32 sectors side by side. If the pawl has been punched out of your Model A sector, it looks as though there isn't room for the hole you wish to make.
|
Sponsored Links (Register now to hide all advertisements) |
|
06-05-2021, 09:46 PM | #3 |
Senior Member
Join Date: May 2010
Location: Kerrville, Tx
Posts: 2,769
|
Re: 32 brake lever sector dimension
I was not going to move the lever pivot hole. I was thinking of moving the mounting holes down. I think I can play with the photos by cutting out the shape of the 32 sector and compairing it to the A sector. The A lever is in bad shape so I am not working with a rare desirable part.
|
06-05-2021, 10:17 PM | #4 |
Senior Member
Join Date: Feb 2017
Location: Rochester Wa
Posts: 574
|
Re: 32 brake lever sector dimension
I have an original complete '32 E brake handle. See thread below. Can you sketch which exact dimension you need and I can measure it. Tom
https://www.fordbarn.com/forum/showthread.php?t=298862 |
06-05-2021, 11:15 PM | #5 |
Senior Member
Join Date: May 2010
Location: Southern France
Posts: 5,301
|
Re: 32 brake lever sector dimension
Here is the one CW Moss sells for $12.95
Last edited by deuce lover; 06-06-2021 at 08:32 AM. |
06-06-2021, 08:14 AM | #6 |
Senior Member
Join Date: May 2010
Location: Kerrville, Tx
Posts: 2,769
|
Re: 32 brake lever sector dimension
Sponsored Links (Register now to hide all advertisements)
|
06-06-2021, 08:56 AM | #7 |
Senior Member
Join Date: May 2010
Location: Solihull, England.
Posts: 8,745
|
Re: 32 brake lever sector dimension
Andy I can do this for you. Give me 10 mins.
Ok. My best guess would be 1/8". The center bolt is 1/8" above the mounting holes. In the pic the center bolt is centered on the edge of the wood bench top. Last edited by Mart; 06-06-2021 at 09:06 AM. |
06-06-2021, 10:15 AM | #8 |
Senior Member
Join Date: May 2010
Location: Kerrville, Tx
Posts: 2,769
|
Re: 32 brake lever sector dimension
Thanks, That is perfect.
I finally realized what the funny lighting hole in the middle is. That is where the paul was stamped out! I would love to help you sometime if I can. |
06-06-2021, 11:15 AM | #9 |
Senior Member
Join Date: May 2010
Location: southeastern Michigan
Posts: 10,096
|
Re: 32 brake lever sector dimension
While you're looking, please note which side the teeth are on, which precludes moving the mounting holes as there is only thin air where they would move to on the Model A sector in replicating the '32 hole pattern.
|
06-06-2021, 11:39 AM | #10 |
Senior Member
Join Date: May 2010
Location: Kerrville, Tx
Posts: 2,769
|
Re: 32 brake lever sector dimension
I will take care!
Deuce Lover, THANKS, I sure was unaware of it being repo'd. Last edited by Andy; 06-06-2021 at 08:16 PM. |
|
|
Sponsored Links (Register now to hide all advertisements) |
|