|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
04-30-2022, 10:02 PM | #1 |
Senior Member
Join Date: Feb 2020
Location: BC Canada
Posts: 573
|
0.083 over piston rings
I've got a set of pistons 0.083" over stock 3 3/16". Were these made for use after removal of stock sleeves? Any ideas where I can track down a set of rings? Tried hastings and no such luck...
__________________
Sometimes, ingenuity gets in the way of sense and sanity. |
05-01-2022, 02:36 AM | #2 | |
Senior Member
Join Date: May 2010
Location: East Shore of LAKE HOUSTON
Posts: 11,113
|
Re: 0.083 over piston rings
Quote:
Will....Did you try contacting Fred Wilner at Southside Obsolete, "barnfind08"(via PM) here on F'Barn? OR James Saccoccio Gotham Auto Parts,LLC 340 Cherry Street Bedford Hills, NY 10507 [email protected] Tel: (718) 878-3699 Coop . |
|
Sponsored Links (Register now to hide all advertisements) |
|
05-01-2022, 10:31 AM | #3 | |
Senior Member
Join Date: May 2010
Location: Wisconsin, USA
Posts: 9,007
|
Re: 0.083 over piston rings
Quote:
The availability of those pistons dried up decades ago making them valuable. I do not know whether or not they are now being reproduced.
__________________
"I can explain it for you. However, I can't understand it for you". |
|
05-01-2022, 11:38 AM | #4 |
Senior Member
Join Date: Feb 2011
Posts: 2,113
|
Re: 0.083 over piston rings
I bought my pistons from Egge for my 8BA. They were their stock 4 ring piston spcl order so it takes a couple of weeks to get them.
Seems like I ran stock Hastings .080 rings, the .003 dia difference shouldn’t translate into a appreciable difference in the final end gap measurement...... Also used total seal to seat the rings.
__________________
Tim Downtown, Ca Last edited by CA Victoria; 05-01-2022 at 11:45 AM. |
05-01-2022, 11:45 AM | #5 |
Senior Member
Join Date: Apr 2019
Location: Kansas
Posts: 921
|
Re: 0.083 over piston rings
I believe JWL posted that he may have some of the .083" over stuff he'd sell. Might contact him to see.
__________________
"It don't take but country smarts to solve the problem" (Smokey Yunick) '41 Merc Town Sedan / 260" 8CM engine '66 Fairlane four door / "warmed up" 302 |
05-01-2022, 03:06 PM | #6 |
Senior Member
Join Date: May 2010
Location: Alabama
Posts: 3,260
|
Re: 0.083 over piston rings
Sponsored Links (Register now to hide all advertisements)
|
05-01-2022, 04:24 PM | #7 |
Senior Member
Join Date: May 2010
Location: Chester Vt
Posts: 8,860
|
Re: 0.083 over piston rings
Might as well go to .125 over. @0 more cubs and one point in CR. Angle mill the heads .070 and get another point in CR. Make a nice driver, with good mirage,
Gramps |
05-01-2022, 05:11 PM | #8 |
Senior Member
Join Date: Sep 2011
Location: Christchurch New Zealand
Posts: 1,611
|
Re: 0.083 over piston rings
I had some plus 83 rings from Egge.
Try them may still have them. Phil NZ |
05-02-2022, 07:09 PM | #9 |
Senior Member
Join Date: Feb 2020
Location: BC Canada
Posts: 573
|
Re: 0.083 over piston rings
Thank you for all the input👍
__________________
Sometimes, ingenuity gets in the way of sense and sanity. |
05-03-2022, 06:50 PM | #10 |
Senior Member
Join Date: May 2010
Location: KC
Posts: 266
|
Re: 0.083 over piston rings
Couple of years ago I got them from Hastings.
|
|
|
Sponsored Links (Register now to hide all advertisements) |
|