The Ford Barn

pzxzqg · 11-04-2015, 02:20 PM

Bought the antique ford green from Synder's to get the engine color right on the 1939 A-model but unclear about painting things like the firewall, generator, starter, water pipes, steering column (engine side), exhaust pipes, ... . I'd like not to get to far off the original track on color but want to use something as durable as possible (rustoleum black gloss enamel paint?). Suggestions?

31Tudor · 11-04-2015, 02:28 PM

Firewall - lower body color
Engine Green- Block, Head, water pump, Water outlet & inlet, Valve cover, intake manifold, flywheel housing, bell housing, transmission, 1st piece of the clamshell that bolts to the rear of the transmission, both timing covers, crank pully

Black Enamel- Fan, lower water pipe, oil return pipe, starter, generator, distributor body, oil fill pipe, accelerator assembly, oil pan, crescent shaped cover that covers the rear main area, two pieces of the clam shell. steering column, coil

Exhaust Manifold- Could be high temp black, cast blast.

Gaskets were not painted

Tom Wesenberg · 11-04-2015, 03:25 PM

Radiator support rods are black also.

Cast iron sediment bulb is semi-gloss black.

Be sure to buy the "STANDARDS" book, as it's a must have book for every Model A owner.

pzxzqg · 11-04-2015, 08:05 PM

Thanks guys. Lot of work ahead.

pzxzqg · 12-05-2015, 12:27 PM

Should I tape off the main lower engine and valve bolts/nuts or OK to paint green as well? I also saw a picture of the engagement mechanism on top of the starter was unpainted. I painted it black. Which is correct? I'd rather correct it now.

Tom Wesenberg · 12-05-2015, 03:08 PM

Sponsored Links (Register now to hide all advertisements)

The bolts and nuts are not painted. I'd leave the starter switch cad plated, but the earlier STANDARDS said it could also be black. I haven't read the latest version of the STANDARDS to see if black is still OK.

11-04-2015, 02:20 PM	#1
pzxzqg Junior Member Join Date: Oct 2015 Location: Allen, TX Posts: 11	Engine compartment/component paint type/color Bought the antique ford green from Synder's to get the engine color right on the 1939 A-model but unclear about painting things like the firewall, generator, starter, water pipes, steering column (engine side), exhaust pipes, ... . I'd like not to get to far off the original track on color but want to use something as durable as possible (rustoleum black gloss enamel paint?). Suggestions?

11-04-2015, 02:28 PM	#2
31Tudor Senior Member Join Date: May 2010 Location: North Carolina Posts: 611	Re: Engine compartment/component paint type/color Firewall - lower body color Engine Green- Block, Head, water pump, Water outlet & inlet, Valve cover, intake manifold, flywheel housing, bell housing, transmission, 1st piece of the clamshell that bolts to the rear of the transmission, both timing covers, crank pully Black Enamel- Fan, lower water pipe, oil return pipe, starter, generator, distributor body, oil fill pipe, accelerator assembly, oil pan, crescent shaped cover that covers the rear main area, two pieces of the clam shell. steering column, coil Exhaust Manifold- Could be high temp black, cast blast. Gaskets were not painted Last edited by 31Tudor; 11-04-2015 at 03:08 PM.

11-04-2015, 03:25 PM	#3
Tom Wesenberg Senior Member Join Date: May 2010 Location: Mpls, MN Posts: 27,582	Re: Engine compartment/component paint type/color Radiator support rods are black also. Cast iron sediment bulb is semi-gloss black. Be sure to buy the "STANDARDS" book, as it's a must have book for every Model A owner.

11-04-2015, 08:05 PM	#4
pzxzqg Junior Member Join Date: Oct 2015 Location: Allen, TX Posts: 11	Re: Engine compartment/component paint type/color Thanks guys. Lot of work ahead.

12-05-2015, 12:27 PM	#5
pzxzqg Junior Member Join Date: Oct 2015 Location: Allen, TX Posts: 11	Re: Engine compartment/component paint type/color Should I tape off the main lower engine and valve bolts/nuts or OK to paint green as well? I also saw a picture of the engagement mechanism on top of the starter was unpainted. I painted it black. Which is correct? I'd rather correct it now. Last edited by pzxzqg; 12-05-2015 at 01:23 PM.

12-05-2015, 03:08 PM	#6
Tom Wesenberg Senior Member Join Date: May 2010 Location: Mpls, MN Posts: 27,582	Re: Engine compartment/component paint type/color Sponsored Links (Register now to hide all advertisements) The bolts and nuts are not painted. I'd leave the starter switch cad plated, but the earlier STANDARDS said it could also be black. I haven't read the latest version of the STANDARDS to see if black is still OK.