Go Back   The Ford Barn > General Discussion > Model A (1928-31)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 05-16-2021, 07:50 PM   #1
Pilotdave
Senior Member
 
Pilotdave's Avatar
 
Join Date: Oct 2010
Location: Grafton, MA
Posts: 1,226
Default LED Tail Lights - Adding Resistors

After installing Signal Stat 900 turn signals a few years ago, I recently converted the tail lights to LED units. The flasher is the old style bimetal type, and the flash rate is quite high. Today I tried to add a 25 watt, 6.5 ohm resistor in parallel to the flasher circuit wiring near the tail lights: one lead attached to the turn signal/brake wire, the other attached to ground. This made zero difference in the flash rate, and I'm hoping to find some hints that will correct this. Any and all ideas are welcome!

Thanks much.
Dave
Pilotdave is offline   Reply With Quote
Old 05-16-2021, 08:08 PM   #2
Synchro909
Senior Member
 
Synchro909's Avatar
 
Join Date: Jun 2014
Location: Melbourne, Australia
Posts: 7,471
Default Re: LED Tail Lights - Adding Resistors

While I've never heard of a Signal Stat 900 (what ever that is!), the usual fix for this is you get yourself an electronic flasher unit. They are made for LED lights and their low energy consumption.
__________________
I'm part of the only ever generation with an analogue childhood and a digital adulthood.
Synchro909 is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 05-16-2021, 08:19 PM   #3
Pilotdave
Senior Member
 
Pilotdave's Avatar
 
Join Date: Oct 2010
Location: Grafton, MA
Posts: 1,226
Default Re: LED Tail Lights - Adding Resistors

The Signal Stat 900 is a US-made turn signal brand. Synder's catalog pictures it (or one just like it) on page A-170 of their 2021 catalog.

Thanks for the suggestion. I've tried the electronic flasher units with no luck - I've read on here that they're very sensitive to electronic noise from the engine, though there may be a way to shield them.

I'm hoping to get some ideas about what I did wrong installing the resistor - according to the videos online I've done it correctly.......and it's a very simple concept that logic says should do the trick!

Thanks.
Dave
Pilotdave is offline   Reply With Quote
Old 05-16-2021, 08:32 PM   #4
shew01
Senior Member
 
shew01's Avatar
 
Join Date: Sep 2016
Location: Roanoke, VA USA
Posts: 1,905
Default Re: LED Tail Lights - Adding Resistors

https://www.snydersantiqueauto.com/P...earchByKeyword


Sent from my iPhone using Tapatalk
shew01 is offline   Reply With Quote
Old 05-16-2021, 08:42 PM   #5
Pilotdave
Senior Member
 
Pilotdave's Avatar
 
Join Date: Oct 2010
Location: Grafton, MA
Posts: 1,226
Default Re: LED Tail Lights - Adding Resistors

Thanks for the link, shew01. The resistors I have are similar, though lower wattage and slightly higher resistance.

I think I've installed the resistors correctly - if anyone has done this and could comment on how I installed them, it'd be a real help.

Thanks!
Pilotdave is offline   Reply With Quote
Old 05-16-2021, 08:53 PM   #6
jayvee34
Senior Member
 
jayvee34's Avatar
 
Join Date: Apr 2021
Location: St. Augustine, Fl.
Posts: 437
Default Re: LED Tail Lights - Adding Resistors

Sponsored Links (Register now to hide all advertisements)
My turn signals are front cowl lights with the O.E. type bulbs, rear are tail lights with
L.E.D. lights. I have a 6 volt system and use a standard 6V flasher unit. My flashers,
right turn, left turn, and emergency flashers works perfectly. My flasher controller system
is made by "EVERLASTING".
John
__________________
IN GOD WE TRUST - SEMPER FIDELIS
John
jayvee34 is offline   Reply With Quote
Old 05-16-2021, 10:27 PM   #7
bruceincam
Senior Member
 
bruceincam's Avatar
 
Join Date: Mar 2021
Location: Camarillo, Ca
Posts: 163
Default Re: LED Tail Lights - Adding Resistors

Dave, I've done the same as you with a 12V neg ground conversion. I'm using a 50W, 6 ohm resistor at each LED tail light. The results are acceptable and what I would call "normal". Same Signal Stat system. Sound like mine are wired just as you describe --- one end to the turn signal wire and the other end to ground. Maybe add a little resistance -- 6.5 ohms isn't much.

Last edited by bruceincam; 05-18-2021 at 12:20 PM.
bruceincam is offline   Reply With Quote
Old 05-17-2021, 12:30 AM   #8
CarlG
Senior Member
 
CarlG's Avatar
 
Join Date: Nov 2010
Location: Anchorage, Alaska
Posts: 9,109
Default Re: LED Tail Lights - Adding Resistors

Dave, you didn't say if you were 6 or 12 volt. I am running 12 volts and found this flasher that works for me perfectly with a Signal Stat 900.
Attached Images
File Type: jpg Flasher.jpg (8.2 KB, 31 views)
__________________
Alaskan A's
Antique Auto Mushers of Alaska
Model A Ford Club of America
Model A Restorers Club
Antique Automobile Club of America
Mullins Owner's Club
CarlG is offline   Reply With Quote
Old 05-17-2021, 04:59 AM   #9
Bruce of MN
Senior Member
 
Bruce of MN's Avatar
 
Join Date: May 2010
Location: VA
Posts: 1,394
Default Re: LED Tail Lights - Adding Resistors

Tom Wesenberg has posted on this, I think. See if there is an answer here:

https://www.fordbarn.com/forum/searc...rchid=22793566
Bruce of MN is offline   Reply With Quote
Old 05-17-2021, 05:33 AM   #10
Patrick L.
Senior Member
 
Patrick L.'s Avatar
 
Join Date: May 2010
Location: Largo Florida
Posts: 7,225
Default Re: LED Tail Lights - Adding Resistors

If you are still using incandescent front lights for the turns, then just replace them with higher candle power bulbs. They'll be available locally or from the vendors. When the 3 cp are replaced with 10cp bulbs there is enough resistance to fire the thermal 535 flasher. I use the cowls and parks as front turns.

I've tried the resisters and electronic flashers too, thats why I just change bulbs.

However since I've played with this there is supposed to be a flasher that will work on 6v, but, I haven't tried it.
Patrick L. is offline   Reply With Quote
Old 05-17-2021, 06:39 AM   #11
Pilotdave
Senior Member
 
Pilotdave's Avatar
 
Join Date: Oct 2010
Location: Grafton, MA
Posts: 1,226
Default Re: LED Tail Lights - Adding Resistors

Thanks very much for all the suggestions. The car is 6v, + ground. The front flashers are the amber lights that mount between the bumper bars. I'll check their wattage and/or see if there's a higher wattage version of the bulb for them.

The 6.5 ohm resistors installed in parallel is intended to lower the resistance of the circuit, thereby increasing the current flow enough to make the flasher unit happy. Thus far the results are defying Ohm's Law!
Pilotdave is offline   Reply With Quote
Old 05-17-2021, 07:38 AM   #12
nkaminar
Senior Member
 
nkaminar's Avatar
 
Join Date: Jan 2012
Location: Western North Carolina
Posts: 3,817
Default Re: LED Tail Lights - Adding Resistors

Pilot Dave,

Check the ground connection using an ohm meter. I chased a problem with my resistors until I found that what I assumed was a good ground point was not. If that does not work, try a resistor with a lower resistance. You can buy these online that are used for modern cars that are converted to LED's.

The flasher modules made for LED's sometimes have a different pinout. Check the letters on the module to see if the pins are in different places. You can wire up an adapter to change the pinout or rewire the socket. Try the adapter first to make sure the LED flasher will work with your car. Also, check the wattage or amperage of the LED flasher module to see if it will handle the current of your turn indicators.
__________________
A is for apple, green as the sky.
Step on the gas, for tomorrow I die.
Forget the brakes, they really don't work.
The clutch always sticks, and starts with a jerk.
My car grows red hair, and flies through the air.
Driving's a blast, a blast from the past.
nkaminar is online now   Reply With Quote
Old 05-17-2021, 07:57 AM   #13
Badpuppy
Senior Member
 
Join Date: Dec 2017
Location: Guthrie, OK
Posts: 1,140
Default Re: LED Tail Lights - Adding Resistors

Your resistors are the right size, I suspect bad ground to the battery. (The return current has to go all the way.)
Badpuppy is offline   Reply With Quote
Old 05-17-2021, 09:55 AM   #14
Y-Blockhead
Senior Member
 
Y-Blockhead's Avatar
 
Join Date: Jul 2011
Location: Redondo Beach, CA
Posts: 5,817
Default Re: LED Tail Lights - Adding Resistors

Quote:
Originally Posted by CarlG View Post
Dave, you didn't say if you were 6 or 12 volt. I am running 12 volts and found this flasher that works for me perfectly with a Signal Stat 900.
That is the same flasher I use in my "self wired" hidden system. I hate the look of the add-on turn signal switch.
Y-Blockhead is offline   Reply With Quote
Old 05-17-2021, 10:48 AM   #15
AL in NY
Senior Member
 
AL in NY's Avatar
 
Join Date: May 2010
Location: Southern Upstate New York
Posts: 1,149
Default Re: LED Tail Lights - Adding Resistors

I have a 6 volt positive ground system with LED directional lights and I've been using this electronic flasher for a couple of years with no problems.
Attached Images
File Type: jpg 6 volt LED flasher.jpg (43.2 KB, 65 views)
__________________
AL in NY
AL in NY is offline   Reply With Quote
Old 05-17-2021, 12:32 PM   #16
Bob Johnson
Senior Member
 
Bob Johnson's Avatar
 
Join Date: May 2010
Location: California
Posts: 976
Default Re: LED Tail Lights - Adding Resistors

I believe that the resistors are only needed if the flasher flashes too SLOW. The resistor increases the current that goes through the bi-metal switch which results in it heating up faster increasing the flash rate.


Bob
Bob Johnson is offline   Reply With Quote
Old 05-17-2021, 05:50 PM   #17
Patrick L.
Senior Member
 
Patrick L.'s Avatar
 
Join Date: May 2010
Location: Largo Florida
Posts: 7,225
Default Re: LED Tail Lights - Adding Resistors

I didn't know you were using the bumper bar lites. I thought you were trying to use the original lights. I think the bumper lites are LED and would then probably need an electronic flasher.
Patrick L. is offline   Reply With Quote
Old 05-17-2021, 07:08 PM   #18
Bruce of MN
Senior Member
 
Bruce of MN's Avatar
 
Join Date: May 2010
Location: VA
Posts: 1,394
Default Re: LED Tail Lights - Adding Resistors

I was able to find 6v bulbs for the trailer marker lites I have on my bumper.
Bruce of MN is offline   Reply With Quote
Old 05-17-2021, 07:13 PM   #19
nkaminar
Senior Member
 
nkaminar's Avatar
 
Join Date: Jan 2012
Location: Western North Carolina
Posts: 3,817
Default Re: LED Tail Lights - Adding Resistors

Bob, the resistors are meant to cure hyperflashing. I know it does not sound logical but that is what they are for. See https://www.superbrightleds.com/blog...rflashing/275/.
__________________
A is for apple, green as the sky.
Step on the gas, for tomorrow I die.
Forget the brakes, they really don't work.
The clutch always sticks, and starts with a jerk.
My car grows red hair, and flies through the air.
Driving's a blast, a blast from the past.
nkaminar is online now   Reply With Quote
Old 05-17-2021, 08:21 PM   #20
Synchro909
Senior Member
 
Synchro909's Avatar
 
Join Date: Jun 2014
Location: Melbourne, Australia
Posts: 7,471
Default Re: LED Tail Lights - Adding Resistors

Quote:
Originally Posted by Pilotdave View Post
After installing Signal Stat 900 turn signals a few years ago, I recently converted the tail lights to LED units. The flasher is the old style bimetal type, and the flash rate is quite high. Today I tried to add a 25 watt, 6.5 ohm resistor in parallel to the flasher circuit wiring near the tail lights: one lead attached to the turn signal/brake wire, the other attached to ground. This made zero difference in the flash rate, and I'm hoping to find some hints that will correct this. Any and all ideas are welcome!

Thanks much.
Dave
What has changing the tail lights got to do with the turn indicators?
__________________
I'm part of the only ever generation with an analogue childhood and a digital adulthood.
Synchro909 is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 07:06 AM.