|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
03-22-2022, 04:40 PM | #1 |
Senior Member
Join Date: May 2014
Location: Ontario
Posts: 207
|
Water pump resurfacer tool
Has any one used this or a similar tool, trying to figure out how you use it/assemble it? I'm assuming I need to cut some sand paper disks ?
instructions are very vague |
03-22-2022, 05:17 PM | #2 |
Senior Member
Join Date: May 2012
Location: Queensland, Australia
Posts: 10,377
|
Re: Water pump resurfacer tool
Water Pump resurfacer tool, need Instructions? - rust revival |
Sponsored Links (Register now to hide all advertisements) |
|
03-23-2022, 12:52 PM | #3 |
Senior Member
Join Date: Jul 2014
Location: Iowa
Posts: 1,634
|
Re: Water pump resurfacer tool
The best choice is to send the pumps to Skip Haney. They will come back as good as new. 941-505-9085 or 941-639-0920. [email protected]
|
03-23-2022, 01:10 PM | #4 |
Senior Member
Join Date: May 2010
Location: NJ
Posts: 6,181
|
Re: Water pump resurfacer tool
I am far from an expert, but that tool may be for early head-in type or V860 pumps. I believe they have a different seal set up than later pump in block type of pumps.
Those arbors looks really long for any type of flathead type pumps though. Could it be for a Model A/B style pump that has a long shaft running through the body? |
03-27-2022, 09:43 AM | #5 |
Senior Member
Join Date: May 2014
Location: Ontario
Posts: 207
|
Re: Water pump resurfacer tool
Number 3 on the rebuild papers also indicate to resurface, I'm posting this to try and help others as well as me, don't get me wrong it's great to send every part you need rebuilt to someone else, but sometimes it's not financially visible,
for me to send water pumps to get a rebuild It would be around $400 that does not make sense to me. |
03-27-2022, 10:21 AM | #6 | |
Senior Member
Join Date: May 2010
Location: East Hartford, Ct
Posts: 5,898
|
Re: Water pump resurfacer tool
Sponsored Links (Register now to hide all advertisements)
Quote:
__________________
DON'T RECALL DOING SOMETHING FOR MYSELF BASED ON SOMEONE ELSE'S LIKES OR DISLIKES |
|
03-27-2022, 11:31 AM | #7 | |
Senior Member
Join Date: Oct 2012
Location: Eastcoast
Posts: 864
|
Re: Water pump resurfacer tool
Quote:
Skips pump rebuilds are a work of art. Better impeller nice and tight on the seal. I have a set of new aftermarket to compare to Skips and there is no comparison. I’m not sure if any of the aftermarket suppliers have the better impeller separate or water pumps with them. I have a pump kit but have been told that it can be fairly difficult to get the pulley off with out it breaking. |
|
03-28-2022, 03:46 AM | #8 |
Senior Member
Join Date: Nov 2012
Location: Tauranga, New Zealand
Posts: 726
|
Re: Water pump resurfacer tool
As I remember, you drill the impellor off, and then press the bearing out from the back. Then it is easy to set up to press off the pulley. I'm talking about a Ford bearing type (truck) pump as an example.
This reamer is just to give you a flat clean surface for the seal to run against, similar to one used to repair the seat in a water tap. |
03-28-2022, 08:11 AM | #9 |
Junior Member
Join Date: Oct 2021
Location: Belvue Kansas
Posts: 15
|
Re: Water pump resurfacer tool
Love the old tools. It is nice to see the kit complete. When you get it to work show us some pictures or video we just might learn something.
|
03-28-2022, 10:44 AM | #10 |
Senior Member
Join Date: Feb 2011
Posts: 794
|
Re: Water pump resurfacer tool
As pointed out in post #6, if there isn't any cutter with the kit, it is worthless.
|
03-28-2022, 11:29 AM | #11 |
Senior Member
Join Date: May 2014
Location: Ontario
Posts: 207
|
Re: Water pump resurfacer tool
Cutters are in bottom left corner of the red box
|
|
|
Sponsored Links (Register now to hide all advertisements) |
|