|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
08-14-2018, 11:08 AM | #1 |
Senior Member
Join Date: Apr 2012
Location: Washington State
Posts: 289
|
1940 brake issue....
My 1940 Tudor is a blast to drive, but the brakes are driving me crazy. The brakes are great....as long as you pump the pedal 1 time. The first press of the pedal is soft, but the second and every consecutive pump after that is rock solid. Everything is new including master cylinder, wheel cylinders, and lines....all stock. I've done quite a bit of reading on here about brake issues and found several people swearing by residual valves, so I installed them in the front and rear lines but not change. There are no leaks visable and no damp locations that I can see anywhere. The fluid level in the MC has not dropped. Last night I removed the sections that have the residual valves and retightened everything....just to make sure. I bled all the brakes again (went through another bottle of fluid just to make sure I got ALL the air out) and still have the same result.
I press on the pedal and its soft, but on the second press its firm. This happens every single time. I even counted to 5 and tried it again....same result....first pump is soft second and all subsequent are firm. If I wait 5 seconds the first pump is soft again. Anyone have any suggestion on what to try next? Is this a sign of a bad MC or maybe I just didn't get it bench bled correctly? Any input is greatly appreciated...... |
08-14-2018, 12:19 PM | #2 |
Senior Member
Join Date: May 2010
Location: Illinois
Posts: 2,187
|
Re: 1940 brake issue....
You might check brake adjustment. If the shoes have too much travel on first pump ,it will take another one to apply brakes.
John |
Sponsored Links (Register now to hide all advertisements) |
|
08-14-2018, 12:42 PM | #3 |
Senior Member
Join Date: Apr 2012
Location: Washington State
Posts: 289
|
Re: 1940 brake issue....
That is an excellent point. I'll check them tonight. Is there a recommendation for brake adjustment or do you just set them so they just don't drag? Thanks for the suggestion.
|
08-14-2018, 02:08 PM | #4 |
Senior Member
Join Date: May 2010
Location: Solihull, England.
Posts: 8,766
|
Re: 1940 brake issue....
Tighten so they drag and then back off just enough so there is minimal drag.
Mart. |
08-14-2018, 02:16 PM | #5 |
Senior Member
Join Date: Mar 2014
Location: Jacksonville FL
Posts: 3,984
|
Re: 1940 brake issue....
Sounds like you still may have air in the master cylinder or in one of the wheel cylinders to me!!! I would double check and make sure ALL the air is out of the system!!!! You didn't specify when you bled your brakes the first time after repairs IF the peddle got hard and stayed hard THEN got to where you have to pump them to get a firm peddle??? Sometimes the master cylinder can be a pain to get the all the air out.
Last edited by rockfla; 08-14-2018 at 02:46 PM. |
08-14-2018, 02:55 PM | #6 |
Senior Member
|
Re: 1940 brake issue....
Sponsored Links (Register now to hide all advertisements)
|
08-14-2018, 04:41 PM | #7 |
Senior Member
Join Date: Jul 2016
Location: Lake worth Florida
Posts: 1,114
|
Re: 1940 brake issue....
Leaning towards improper adjustment of shoes and possible master cyl rod if changed to a new master cyl
|
08-14-2018, 06:14 PM | #8 |
Senior Member
Join Date: May 2010
Location: Mid coast Maine
Posts: 1,878
|
Re: 1940 brake issue....
Those redial valves are good for dual MVP
One thing people do to bleed is to pinch the rubber hoses That could be your problem |
08-14-2018, 11:02 PM | #9 |
Senior Member
Join Date: May 2010
Location: Mn
Posts: 2,412
|
Re: 1940 brake issue....
Below I listed a link to an older thread by Paul Garrigan on adjusting '39-'42 Ford brakes.
Deleted the Link for adjusting brakes, as it was not needed. .
__________________
If mama ain't happy, ain't nobody happy. But if daddy ain't happy...RUN Last edited by Lanny; 08-24-2018 at 12:22 PM. |
08-14-2018, 11:45 PM | #10 |
Senior Member
Join Date: Apr 2012
Location: Washington State
Posts: 289
|
Re: 1940 brake issue....
I just got done adjusting the brakes and although the rears seemed pretty close, the fronts were quite a bit off. I had to turn each adjuster almost 1/3 rotation before the drug slightly. I will take the car for a drive tomorrow or Thursday and see what it feels like, but with it on the lift it feels like the pedal is quite a bit more firm on the first push. Fingers crossed.....
I'm fairly certain I've got all the air out of the lines. I installed speed bleeders and pumped nearly a full bottle through the system....slow strokes and watching the hose closely. I know the MC can be tricky so that could be the culprit if it's still having issues. The MC is a new stock 40 Ford single pot so I'd think all the geometry is correct. Let's hope it was just br as ke adjustment. Thanks everyone for the input. I appreciate the suggestions and advice. Sent from my SM-G960U using Tapatalk |
08-16-2018, 02:16 PM | #11 |
Senior Member
Join Date: May 2010
Location: Illinois
Posts: 2,187
|
Re: 1940 brake issue....
Let us know how it turns out.
John |
08-16-2018, 10:33 PM | #12 |
Senior Member
Join Date: Aug 2012
Location: Perth, Western Australia
Posts: 2,687
|
Re: 1940 brake issue....
Dont let the pedal go all the way to the floor when you bleed a single M/C . Speedbleeders are a great help.
__________________
"Came too close to dying to stop living now!" |
08-22-2018, 01:40 PM | #13 |
Senior Member
Join Date: Apr 2012
Location: Washington State
Posts: 289
|
Re: 1940 brake issue....
Sorry for the late response. I've driven the car a couple days and although the brakes are better, they still aren't great until I pump them 1 time.
I put the car on the lift last night and went over every connection on the brake system. Everything is BONE dry from the MC to the backing plates. I checked the brakes again and was able to adjust the passenger front a hair tighter. I'm going to drive it a few more times and I'll update again. The brakes work and I can stop without pumping them, but it is a noticeable difference in pedal feel and brake pressure if I simply pump the pedal once whenever I need to use the brakes. Any suggestions on stuff to try? I can bleed them more but I've already gone through a full bottle of brake fluid the last time. Maybe I'm expecting too much from the old original system? Thanks again for all the suggestions and info. I'll post again in a week or so...... |
08-22-2018, 01:54 PM | #14 |
Senior Member
Join Date: May 2010
Location: Solihull, England.
Posts: 8,766
|
Re: 1940 brake issue....
Well it's an improvement at least.
can you give us a clue as to the state of the linings, the diameter of the drums, the fit of the shoes to the drum, (have the shoes been "arced" to the drums), the adjustment procedure, did it include the eccentrics?. I have exactly the same setup on my 41 pickup, completely stock from one end to the other and that stops pretty well, so there must be something on your car that is not as good as on my pickup. I do not have any extra valving, just a new replacement master cylinder. I arced the shoes to the drums using wet and dry inside the drum and rubbed the shoe back and forth. I adjusted them following a procedure that included the eccentrics. I swapped out an oversize drum and replaced it with one in better shape. There are lots of things that could cause loss of pedal efficiency. Mart. |
08-22-2018, 02:01 PM | #15 |
Senior Member
Join Date: May 2010
Location: Southern California
Posts: 7,046
|
Re: 1940 brake issue....
If everything is new you will need to adjust the brakes in 4 places for each wheel. Be sure to read and follow the instructions.
Charlie Stephens |
08-22-2018, 02:04 PM | #16 |
Senior Member
Join Date: May 2010
Location: Mid coast Maine
Posts: 1,878
|
Re: 1940 brake issue....
When bleeding the brakes best get the MC higher then WC jack up front or back as needed.
When I do mine I just crack the bleeder just enough to leak out and pump 10 times and when you see puddle on ground quick close bleeder. Keep MC full and do rest same way. Gravity does work that way. Make sure piston MC is all the way back. 1/8 play |
08-22-2018, 02:45 PM | #17 |
Senior Member
|
Re: 1940 brake issue....
We have the opposite problem here with a 30 Chrysler it has a 3" master cylinder matched with a 1,1/4 wheel cylinders .its a very hard unresponsive pedal ,its about fluid displacement ,give us the cylinder sizes your new cylinder maybe to small ,did it have that problem with old M/C, Ted
|
08-22-2018, 07:22 PM | #18 | |
Senior Member
Join Date: Aug 2012
Location: Perth, Western Australia
Posts: 2,687
|
Re: 1940 brake issue....
Quote:
Thats what I was thinking .. Your linings might be undersize for the drum. If you lean on the pedal will it stop properly or ......aghh not! I chased this problem in my 56 Fairlane for ages , normal braking ok but stopping hard just didnt happen.. Someone previous had just put 'standard' linings in without checking the diameter of the drum. Here in Australia we go by 1st,2nd, 3rd oversize. When measured correctly these will fit the drum correctly and no need for arcing. Boy does it stop now!
__________________
"Came too close to dying to stop living now!" |
|
08-24-2018, 10:50 AM | #19 |
Senior Member
Join Date: May 2010
Location: NorCal
Posts: 2,617
|
Re: 1940 brake issue....
Get a new Master Cylinder.
Thank me later Jim |
08-24-2018, 11:39 AM | #20 |
Senior Member
Join Date: Dec 2010
Location: North of sandy ago, CA.
Posts: 2,064
|
Re: 1940 brake issue....
Adavis
Would you be using DOT 5 silicone fluid? Bruce
__________________
Works good Lasts long time |
08-24-2018, 12:02 PM | #21 |
Senior Member
Join Date: Apr 2012
Location: Washington State
Posts: 289
|
Re: 1940 brake issue....
I pulled the front drums off last night. The shoes are basically new as well as the wheel cylinders but the drums have some grooves. The shoes dont appear to have been "arched" to match the drums as there only looks to be contact at either end of each shoe.
I have a pair of nice late style heavy drums that look excellent. I dropped them off at the local shop this morning to be cleaned and trued. I had to order new seals so I'll get them installed next week. I'm also going to sand the shoes to match the drums once I get them back. When I adjusted the brakes I first loosened the outer nuts on the lower adjusters then spun the wheel and turned one adjuster till it drug, then backed off till it was just free. I did the same to the other lower adjuster and then tightened both nuts. The I moved to the two upper adjusters (eccentrics?). I spun the wheel and turned each adjuster until it drug then backed off slightly. If this is not the correct procedure feel free to let me know. I'm using plain old DOT3 brake fluid. I have new speed bleeders installed on all corners and have ran fluid through each wheel until there are no bubbles....and then ran more fluid just to be sure. Thanks again for all the input. I still can't believe that brake adjustment would be the culprit to my brake pumping dilemma, but I'm going through everything and learning while I do it. I'll keep you posted on the outcome..... Sent from my SM-G960U using Tapatalk |
08-24-2018, 12:28 PM | #22 |
Senior Member
Join Date: May 2010
Location: Mid coast Maine
Posts: 1,878
|
Re: 1940 brake issue....
If you have new shoes there are some shoes that are made wrong.
The bottom hole is off location. If you put shoes in drum make sure the lining hits all drum, chamfer ends. Now look and see if any of the shoe is less then 1/4. What I mean is if you wore down the lining the bottom 2" should not hit drum. If you have old shoe look at new shoes at bottom hole. |
Sponsored Links (Register now to hide all advertisements) |
|
09-08-2018, 10:03 PM | #23 |
Senior Member
Join Date: Apr 2012
Location: Washington State
Posts: 289
|
Re: 1940 brake issue....
So I have an update. I swapped the front drums with a pair of freshly turned drums that measure 12.050". I pulled the master cylinder and bench bled it. After I reinstalled the MC I bled the system starting with the right rear wheel. Using speed bleeders I'm able to do everything by myself with the car on my lift. I can pump the brake pedal by pulling down on the arm from under the car....giving me the ability to watch the clear line I attach to the bleeder. It took about 25 slow pumps to get completely bubble-free fluid out of the right wheel cylinder. Moving to the left rear cylinder it only took about 10 pumps. Right front was about 10 and left front was about 3.
After all was done I can say that the brakes are as good as I would ever expect original 1940 drums brakes to be. The pedal is firm each press and feels very solid. I have found an old Ammco brake shoe arc-ing machine and will be picking it up in a week or so. When I get that machine I'll double check the shoes just to make sure, but right now I'd consider the brakes good. Thanks everyone for the information and advice. I'd say that the problem was a culmination of several things....from brake adjustment to bench bleeding the master cylinder to starting at the right rear wheel when bleeding the system. Sent from my SM-G960U using Tapatalk |
09-09-2018, 03:02 AM | #24 |
Senior Member
Join Date: May 2010
Location: Solihull, England.
Posts: 8,766
|
Re: 1940 brake issue....
Cool. Thanks for the update.
Mart. |
|
|
Sponsored Links (Register now to hide all advertisements) |
|