|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
01-01-2021, 02:33 PM | #1 |
Senior Member
Join Date: May 2010
Posts: 4,484
|
32 Ford door lock cylinder
I lost the contact information of the man who rebuilds and re keys 32 lock cylinders. He did a couple for me several years ago and they worked good. Can anyone help? I need another one done. Thanks
|
01-01-2021, 02:37 PM | #2 |
Senior Member
Join Date: May 2010
Location: Kerrville, Tx
Posts: 2,770
|
Re: 32 Ford door lock cylinder
You may be looking for 32Phil
|
Sponsored Links (Register now to hide all advertisements) |
|
01-01-2021, 02:40 PM | #3 |
Senior Member
Join Date: May 2010
Location: southeastern Michigan
Posts: 10,101
|
Re: 32 Ford door lock cylinder
Likely 32Phil of upstate New York. I highly recommend him, however he may have escaped to Florida for the winter.
|
01-01-2021, 03:44 PM | #4 |
Senior Member
Join Date: May 2010
Location: Southern France
Posts: 5,307
|
Re: 32 Ford door lock cylinder
You might have to wait until April unless you contact the other locksmith who is a member here.
|
01-01-2021, 04:13 PM | #5 |
Senior Member
Join Date: May 2010
Posts: 4,484
|
Re: 32 Ford door lock cylinder
I'm in no hurry, I won't need the cylinder until early summer.
|
01-01-2021, 07:36 PM | #6 |
Senior Member
Join Date: Jul 2012
Location: Bellingham, WA
Posts: 213
|
Re: 32 Ford door lock cylinder
Sponsored Links (Register now to hide all advertisements)
|
01-01-2021, 07:43 PM | #7 |
Senior Member
Join Date: Nov 2020
Location: SW WA
Posts: 639
|
Re: 32 Ford door lock cylinder
|
01-02-2021, 12:30 AM | #8 |
Senior Member
Join Date: Jan 2011
Location: sw minnesota
Posts: 4,577
|
Re: 32 Ford door lock cylinder
32 Phil has done some work for me also. even though he is down south, i'll bet he visits the barn occasionally, and a PM would get his attention to get the ball in motion.
|
01-02-2021, 07:05 AM | #9 |
Senior Member
Join Date: May 2010
Posts: 4,751
|
Re: 32 Ford door lock cylinder
Also a member here John McClure in N.C.
|
01-02-2021, 08:08 AM | #10 |
Senior Member
Join Date: May 2010
Location: Minnesota
Posts: 558
|
Re: 32 Ford door lock cylinder
32phil. 845-551-5132. Early Ford lock & Key Service
|
01-02-2021, 06:32 PM | #11 |
Senior Member
Join Date: Jul 2012
Location: Bellingham, WA
Posts: 213
|
Re: 32 Ford door lock cylinder
John McClure "FlatHeadCoupe" did all the locks for my '40. Excellent work and had them back to me in a week...
|
01-03-2021, 12:39 PM | #12 |
Senior Member
Join Date: May 2010
Location: QUICKSBURG VA
Posts: 707
|
Re: 32 Ford door lock cylinder
2nd John McClure. Excellent work & reasonable
|
01-03-2021, 03:21 PM | #13 |
Senior Member
Join Date: May 2012
Location: Raleigh, NC 27616
Posts: 208
|
Re: 32 Ford door lock cylinder
Thanks for the compliments. Welcome all lock work/questions from '32 to '56.
Many handles, column drops, and lock assemblies in stock, all OEM, some NOS parts. "cut-keys-to-code", but better to have lock in hand for tweaking. Regards, FlatHeadCoupe |
01-19-2021, 07:30 PM | #14 |
Senior Member
Join Date: Nov 2011
Location: Gonzales, LA
Posts: 457
|
Re: 32 Ford door lock cylinder
I have a door lock cylinder that I need keyed to the ignition key. Anybody know how to disassemble the door lock cylinder on these old Fords?
__________________
Brad Williamson |
01-19-2021, 07:55 PM | #15 |
Senior Member
Join Date: May 2010
Location: Napa,California
Posts: 6,037
|
Re: 32 Ford door lock cylinder
Usually if you look in the door jamb in the area where the lock enters the door you will spot a small hole in the jamb. In that hole you will spot a set screw. That screw holds the lock assembly in the door. Many times that screw has been in there for a long time so you need to use something like PB Blaster to soak it to try to get it loose. If the set screw has a slot for a regular screw driver be very careful not to put too much pressure when trying to loosen the screw. Once the set screw is backed out the lock assembly can be pulled out. If one side of the slot breaks off you are basically doomed to ever get the lock out.
|
01-20-2021, 08:39 AM | #16 |
Senior Member
Join Date: Nov 2011
Location: Gonzales, LA
Posts: 457
|
Re: 32 Ford door lock cylinder
Yes, I have the lock cylinder removed. My question was regarding the lock cylinder itself. I have seen that the later Ford lock cylinders have an easy to remove cover holding the pins and springs in and removing that cover and rearranging the pins allows one to rekey the lock.
The lock I have has a cover but I have no idea how to open it up. I only have one ignition key so I am hesitant to mail it off with the cylinder to have the cylinder rekeyed plus I like to attempt to do things myself if it is possible.
__________________
Brad Williamson |
01-20-2021, 08:54 AM | #17 |
Senior Member
Join Date: May 2010
Location: Wildwood, MO. (near St. Louis)
Posts: 1,792
|
Re: 32 Ford door lock cylinder
Does your lock cylinder have a code stamped on the side. It should have 2 letters followed by 3 numbers...FD123 for example. If you have that you can get a key cut with out too much trouble.
|
01-20-2021, 09:01 AM | #18 |
Senior Member
Join Date: Nov 2011
Location: Gonzales, LA
Posts: 457
|
Re: 32 Ford door lock cylinder
I didn't see one Don but I'll double check.
BTW.. I was born in Cape Girardeau and my car was my grandpa's and spent most of its life in Essex, MO.
__________________
Brad Williamson |
01-20-2021, 09:06 AM | #19 |
Senior Member
Join Date: Nov 2011
Location: Gonzales, LA
Posts: 457
|
Re: 32 Ford door lock cylinder
Also... I Just realized I have kinda hijacked this thread. My apologies. I have PM'd Flatheadcoupe.
__________________
Brad Williamson |
01-20-2021, 12:47 PM | #20 |
Senior Member
Join Date: May 2010
Location: Montgomery, NY & Port St. Lucie Florida
Posts: 936
|
Re: 32 Ford door lock cylinder
Hi Guys
Thanks for the kind compliments. I'm in Florida till April I'll be glad to help when I get back. I'm on the Barn at least once a day sooo you can PM me or call my cell 845 551 5132 Stay safe and well
__________________
Early Ford Lock & Key Service http://www.fordbarn.com/forum/showthread.php?t=46583 |
|
|
Sponsored Links (Register now to hide all advertisements) |
|