Go Back   The Ford Barn > General Discussion > Early V8 (1932-53)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 03-03-2021, 06:56 PM   #1
jason78613
Junior Member
 
jason78613's Avatar
 
Join Date: Oct 2020
Location: Cedar Park, TX
Posts: 20
Default carb leaking gas, what did I do wrong?

Got a rebuilt Stromberg 81 carb from Uncle max, and a new fuel pump from Charlie NY for my '38 60hp. Car is smooth at idle but sputtering when I accelerate hard. After extensively reading through the forum, figured I'd check the float level...

I removed the screws around the top of the carb and lifted the top, cranked the engine a bit and it filled up the float bowl just fine... I'm not an expert, but everything looked right based on reading.

I put the top back on, tried to start the car, but it wasn't starting at all, and after a bit of cranking, quite a bit of gas seeped out of the hole where the accelerator pump goes into the top of the float bowl. (see attached picture) I removed the top again and checked the accelerator pump rod and the felt washer is there, along with the metal washer, springs, etc, but not sure if I'm missing something else?

Did I do something wrong? What typically prevents gas from coming out of that hole? what is causing gas to come out of that hole now?

I'm a noob, go easy on me.
Attached Images
File Type: jpg IMG_3444.jpg (38.8 KB, 369 views)

Last edited by jason78613; 03-03-2021 at 11:32 PM.
jason78613 is offline   Reply With Quote
Old 03-03-2021, 07:02 PM   #2
petehoovie
Senior Member
 
petehoovie's Avatar
 
Join Date: May 2015
Posts: 7,924
Default Re: Not sure what I did wrong, carb leaking gas

Quote:
Originally Posted by jason78613 View Post
Got a rebuilt Stromberg 81 carb from Uncle max, and a new fuel pump from Charlie NY for my '38 60hp. Car is smooth at idle but sputtering when I accelerate hard. After extensively reading through the forum, figured I'd check the float level...

I removed the screws around the top of the carb and lifted the top, cranked the engine a bit and it filled up the float bowl just fine... I'm not an expert, but everything looked right based on reading.

I put the top back on, tried to start the car, but it wasn't starting at all, and after a bit of cranking, quite a bit of gas seeped out of the hole where the accelerator pump goes into the top of the float bowl. (see attached picture) I removed the top again and checked the accelerator pump rod and the felt washer is there, along with the metal washer, springs, etc, but not sure if I'm missing something else?

Did I do something wrong? What typically prevents gas from doing out of that hole? what is causing gas to come out of that hole now?

I'm a noob, go easy on me.
__________________
The only thing nice about being imperfect is the joy it brings to others....

"Silver rings, your butt! Them's washers!"
"We shot our way out of that town for a dollar's worth of steel holes!" - from 'The Wild Bunch' - 1969

https://www.youtube.com/watch?v=7NReUd2_0u0
petehoovie is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 03-03-2021, 07:26 PM   #3
Ken hash
Member
 
Ken hash's Avatar
 
Join Date: Dec 2020
Location: Ellensburg wa
Posts: 58
Default Re: Not sure what I did wrong, carb leaking gas

The 81 is a nice carb. When you take the top of the carb you see a float that is attached to a needle. When the gas rises the needle goes into the seat and stop the gas from coming in. It could be that the float is not correctly adjusted. Stomberg has a website with lots of information and diagrams. Good luck
Ken hash is offline   Reply With Quote
Old 03-03-2021, 07:35 PM   #4
51 MERC-CT
Senior Member
 
51 MERC-CT's Avatar
 
Join Date: May 2010
Location: East Hartford, Ct
Posts: 5,898
Default Re: Not sure what I did wrong, carb leaking gas

Sputtering on acceleration seems to indicate issues with the accelerator pump (bad pump leather/rubber etc.)
__________________
DON'T RECALL DOING SOMETHING FOR MYSELF BASED ON SOMEONE ELSE'S LIKES OR DISLIKES
51 MERC-CT is offline   Reply With Quote
Old 03-03-2021, 10:04 PM   #5
Charlie ny
BANNED
 
Join Date: May 2010
Posts: 3,019
Default Re: Not sure what I did wrong, carb leaking gas

Jason,
Your pump delivered 2 1/2 psi on my test motor, it should be very close to that
on yours. I'm upset but never surprised when something like this occurs. Uncle Max
will be here shortly....I think I just heard him.
Charlie ny
Charlie ny is offline   Reply With Quote
Old 03-03-2021, 10:06 PM   #6
jason78613
Junior Member
 
jason78613's Avatar
 
Join Date: Oct 2020
Location: Cedar Park, TX
Posts: 20
Default Re: Not sure what I did wrong, carb leaking gas

Sponsored Links (Register now to hide all advertisements)
Thanks Charlie, I’m sure your fuel Pump and Max’s carb are good based on all the forum reviews and recommendations, I’m just wondering of I did something wrong?

It was running without leaks until I opened the top of the carb... so not sure what the culprit is. I just wished I hadn’t messed with it.
jason78613 is offline   Reply With Quote
Old 03-03-2021, 10:07 PM   #7
drolston
Senior Member
 
drolston's Avatar
 
Join Date: Jun 2014
Location: Williamsburg, VA
Posts: 1,622
Default Re: Not sure what I did wrong, carb leaking gas

Nothing keeps gas from coming out of that hole where the accelerator pump plunger rod enters the float bowl. That felt washer is only there to keep dirt from getting in; there is no pressure seal because the float bowl must be vented to atmospheric pressure.

So, your test proved that under low fuel pressure from the fuel pump at cranking speed, the float needle shut off fuel at the correct level. When running, I suspect that fuel pressure from the fuel pump is exceeding the pressure that the float needle can withstand. Anything over 3.5 psi can cause problems. I use a pressure regulator set at 2.5 psi, and that is still plenty of flow for drag racing (just kidding; don't do that any more).

If too much pressure is the case, the bowl will fill too high and tend to flood the engine. It will run really rough. You will probably have a strong smell of gas under the hood, or even in the car.
drolston is offline   Reply With Quote
Old 03-03-2021, 10:35 PM   #8
jason78613
Junior Member
 
jason78613's Avatar
 
Join Date: Oct 2020
Location: Cedar Park, TX
Posts: 20
Default Re: Not sure what I did wrong, carb leaking gas

Quote:
Originally Posted by drolston View Post
Nothing keeps gas from coming out of that hole where the accelerator pump plunger rod enters the float bowl. That felt washer is only there to keep dirt from getting in; there is no pressure seal because the float bowl must be vented to atmospheric pressure.

So, your test proved that under low fuel pressure from the fuel pump at cranking speed, the float needle shut off fuel at the correct level. When running, I suspect that fuel pressure from the fuel pump is exceeding the pressure that the float needle can withstand. Anything over 3.5 psi can cause problems. I use a pressure regulator set at 2.5 psi, and that is still plenty of flow for drag racing (just kidding; don't do that any more).

If too much pressure is the case, the bowl will fill too high and tend to flood the engine. It will run really rough. You will probably have a strong smell of gas under the hood, or even in the car.
I have a rebuilt fuel pump from Charlie set at 2.5 psi, and it was running fine with no leaks before I opened the carb... I didn’t change anything else??

I just tried it again and it started up but after a few seconds, the gas started pouring out of that hole, so I shut it down again! Don’t know what else to do, :-(

Last edited by jason78613; 03-03-2021 at 10:46 PM.
jason78613 is offline   Reply With Quote
Old 03-03-2021, 11:36 PM   #9
Charlie ny
BANNED
 
Join Date: May 2010
Posts: 3,019
Default Re: carb leaking gas, what did I do wrong?

Jason,
Let's do this....send me the pump and carb, I'll install both on my test motor
and get back to you on the Barn with an assessment. No charge. I'll cover return

shipping. The moment the parts get here I'll install them and have them heading back

to CEDAR PARK the next day.
Charlie
Charles Schwendler
5845 Cole Rd.
Orchard Park, N.Y.
14127

Last edited by Charlie ny; 03-03-2021 at 11:36 PM. Reason: h missing in chalie
Charlie ny is offline   Reply With Quote
Old 03-03-2021, 11:56 PM   #10
Anteek29
Senior Member
 
Anteek29's Avatar
 
Join Date: Dec 2014
Location: Santa Maria, CA
Posts: 984
Default Re: carb leaking gas, what did I do wrong?

Sure sounds like a problem with the float needle valve. I am curious to learn what Charlie discovers.
__________________
Alan
1929 Special Coupe
1941 Pick-Up
1955 Victoria
Anteek29 is offline   Reply With Quote
Old 03-04-2021, 05:19 AM   #11
moefuzz
Senior Member
 
moefuzz's Avatar
 
Join Date: May 2010
Location: Under A Clean V8
Posts: 228
Default Re: carb leaking gas, what did I do wrong?

.Your fuel pump is mechanical or electric?

The original mechanical fuel pump on top of your intake may be pushing to much pressure.

Your carb is not designed to handle over pressure for very long and can be over
powered by the fuel pump in a matter of seconds, minutes or hours...
...until it can't physically hold back the excess pressure anymore and it will finally give up.


Quick and easy fix=


You can add an extra gasket (or 2) underneath the fuel pump stand at the intake,

this has the effect of shortening the fuel pump pushrod and will decrease fuel pump pressure somewhat.

The longer the fuel pump pushrod "appears" in relation to the physical height to were it is mounted dictates fuel pressure.


So Hypothetically, if you (don't do it!) were to grind the fuel pump push rod a 1/16th or an 1/8th inch, it would have a shorter stroke and would not push the pump as far or as hard.

Adding an extra gasket under the fuel pump stand at the intake
has the effect of shortening the rod and lowering fuel pump pressure.
You can add one or 2 extra gaskets and experiment.

Don't ever grind the fuel pump pushrod to lower fuel pressure or push or stroke at the fuel pump as this is not easily reversible and over time the mechanical fuel pump looses some of it's pressure at which point you can always pull one of the extra gaskets out.

Also, there are 2 different fuel pump pushrods lengths depending on your intake.

Check that yours is close to the below specs dependent upon aluminum or cast intake manifold.

52-9400-A Push Rod - Fuel Pump (V8-60hp) - Alum. Intake (5.625")

52-9400-B Push Rod - Fuel Pump (V8-60hp) - Cast Iron (6.375")



Back in the old days gaskets were relatively thick,
now a days gaskets are less then paper thin so you may have
inadvertently/unknowingly "adjusted" the fuel pump pressure
upwards by installing a paper thin gasket and you wouldn't
even know it until the needle and seat (float) are
over powered and flooding happens..


Extra gaskets are cheap,

...Cheap enough to buy a couple and still have money for your morning donut






.
Attached Images
File Type: jpg 64-15016.jpg (15.5 KB, 281 views)

Last edited by moefuzz; 03-04-2021 at 06:04 AM.
moefuzz is offline   Reply With Quote
Old 03-04-2021, 05:54 AM   #12
Mart
Senior Member
 
Mart's Avatar
 
Join Date: May 2010
Location: Solihull, England.
Posts: 8,732
Default Re: carb leaking gas, what did I do wrong?

Top quality service there from Charlie NY. ^^^^^
Mart is offline   Reply With Quote
Old 03-04-2021, 07:30 AM   #13
Terry,OH
Senior Member
 
Terry,OH's Avatar
 
Join Date: May 2010
Posts: 4,725
Default Re: carb leaking gas, what did I do wrong?

I can not say what Max did to the Carb. except he does excellent work and so does Charlie! if the input valve has the two steel balls that control fuel flow they are somewhat sensitive to dirt. I note you are using a fuel flex line to feed fuel to the Carb. If a piece of rubber gets into the input valve the two balls will not be able to control fuel level properly. This can lead to excessive fuel level and fuel coming out exactly where you have fuel. I suggest you change the rubber fuel line to a new steel line with the proper fittings. The input valve can be removed and cleaned, without taking the Carb apart.
Terry,OH is offline   Reply With Quote
Old 03-04-2021, 07:45 AM   #14
Charlie ny
BANNED
 
Join Date: May 2010
Posts: 3,019
Default Re: carb leaking gas, what did I do wrong?

Regarding #11....a V8 60 does not have a separate f/p stand....the stand is integral with the intake. Terry has good ideas as always but my offer works best if I can put
the patient on the table direct from the accident scene.
Charlie ny
Charlie ny is offline   Reply With Quote
Old 03-04-2021, 09:18 AM   #15
jason78613
Junior Member
 
jason78613's Avatar
 
Join Date: Oct 2020
Location: Cedar Park, TX
Posts: 20
Default Re: carb leaking gas, what did I do wrong?

Quote:
Originally Posted by Charlie ny View Post
Regarding #11....a V8 60 does not have a separate f/p stand....the stand is integral with the intake. Terry has good ideas as always but my offer works best if I can put
the patient on the table direct from the accident scene.
Charlie ny
Thanks Charlie!... I’m going to open the top of the carb once more to check that the valve/needle is seating correctly, and that the float is controlling the fuel correctly...

I’m hoping it’s an easy fix since it was working fine before I messed with it. Perhaps Terry’s note about a piece of rubber (or simmer other crud) getting stuck in the valve is the culprit.

if I can’t figure it out, I’ll be sending the pump and carb to you.
jason78613 is offline   Reply With Quote
Old 03-04-2021, 09:22 AM   #16
Jake dalka
Member
 
Join Date: Oct 2019
Location: Middletown, PA
Posts: 30
Default Re: carb leaking gas, what did I do wrong?

Very impressed with Charlie ny offer....
Willing offer to help solve the issue.....
I’ll remember that and share with others....
Jake dalka is offline   Reply With Quote
Old 03-04-2021, 10:28 AM   #17
jason78613
Junior Member
 
jason78613's Avatar
 
Join Date: Oct 2020
Location: Cedar Park, TX
Posts: 20
Default Re: carb leaking gas, what did I do wrong?

UPDATE:

I took the top off the carb, removed the inlet valve, all looks good and clean, no crud. float moves up and down just fine...

I left the carb open and cranked the engine (I have a button on the starter solenoid so was able to watch it)... the fuel bowl started filling with gas, but the float never rose up! I stopped cranking when the gas was starting to overflow out of the bowl.

Then I noticed small bubbles forming (see attached pic). I read you're supposed to check for float leaks by submerging in hot water, but do those bubble also indicates a pinhole leak in the float? Or is that just a small air leak somewhere in my fuel line (quite possible as I have a small drip at the gas tank where I need to replace the fitting).

Any other reason why the float would not lift?

jason78613 is offline   Reply With Quote
Old 03-04-2021, 11:25 AM   #18
38bill
Senior Member
 
38bill's Avatar
 
Join Date: Apr 2014
Location: Minnesota
Posts: 1,162
Default Re: carb leaking gas, what did I do wrong?

Can you lift the float up manually? Also try to push in the metal ball of the input valve to see if its sticking.
38bill is offline   Reply With Quote
Old 03-04-2021, 11:48 AM   #19
jason78613
Junior Member
 
jason78613's Avatar
 
Join Date: Oct 2020
Location: Cedar Park, TX
Posts: 20
Default Re: carb leaking gas, what did I do wrong?

Quote:
Originally Posted by 38bill View Post
Can you lift the float up manually? Also try to push in the metal ball of the input valve to see if its sticking.
Yep, the float moved up and down freely.
jason78613 is offline   Reply With Quote
Old 03-04-2021, 11:53 AM   #20
51 MERC-CT
Senior Member
 
51 MERC-CT's Avatar
 
Join Date: May 2010
Location: East Hartford, Ct
Posts: 5,898
Default Re: carb leaking gas, what did I do wrong?

Pull the float to determine if it has gas in it.
__________________
DON'T RECALL DOING SOMETHING FOR MYSELF BASED ON SOMEONE ELSE'S LIKES OR DISLIKES
51 MERC-CT is offline   Reply With Quote
Old 03-04-2021, 11:55 AM   #21
jason78613
Junior Member
 
jason78613's Avatar
 
Join Date: Oct 2020
Location: Cedar Park, TX
Posts: 20
Default Re: carb leaking gas, what did I do wrong?

Quote:
Originally Posted by 51 MERC-CT View Post
Pull the float to determine if it has gas in it.
Ok, that will be my next task.

EDIT:

Ah ha! I just removed the carb off the car and pulled out the float and gave it a shake... sure enough, it's full of gas! I wiped it dry and I can see gas seep out immediately... I guess a new float is in order!

At least I now know what the culprit is. (probably could've found it a lot sooner but I'm still learning so always afraid of taking things apart and risk making it worse, or not being able to put it back together correctly.)

Thanks everyone!

Last edited by jason78613; 03-04-2021 at 12:13 PM.
jason78613 is offline   Reply With Quote
Old 03-04-2021, 12:21 PM   #22
Anteek29
Senior Member
 
Anteek29's Avatar
 
Join Date: Dec 2014
Location: Santa Maria, CA
Posts: 984
Default Re: carb leaking gas, what did I do wrong?

Floats, like people can be prone to have gas!
__________________
Alan
1929 Special Coupe
1941 Pick-Up
1955 Victoria
Anteek29 is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 03-04-2021, 12:35 PM   #23
jason78613
Junior Member
 
jason78613's Avatar
 
Join Date: Oct 2020
Location: Cedar Park, TX
Posts: 20
Default Re: carb leaking gas, what did I do wrong?

I was really hoping to attend a car show happening this Sat... would it be a good idea to drill a tiny hole in the float (just to get the gas out), then patch it up with some gas tank repair epoxy like this one?

https://www.autozone.com/sealants-gl...it/698473_0_0?

At least as a temporary solution until the new float arrives?
jason78613 is offline   Reply With Quote
Old 03-04-2021, 12:39 PM   #24
Charlie ny
BANNED
 
Join Date: May 2010
Posts: 3,019
Default Re: carb leaking gas, what did I do wrong?

Jason,

I know MAX and I know he'll do you right. By the way do not submerge the float
in hot water....luke warm is sufficient....hats off to '51 MERC -CT
J B Weld is good stuff but in this situation I would not do it.


Charlie ny

Last edited by Charlie ny; 03-04-2021 at 12:44 PM. Reason: J B weld note added
Charlie ny is offline   Reply With Quote
Old 03-04-2021, 01:01 PM   #25
Will D
Senior Member
 
Will D's Avatar
 
Join Date: Feb 2020
Location: BC Canada
Posts: 573
Default Re: carb leaking gas, what did I do wrong?

Quote:
Originally Posted by Charlie ny View Post
Jason,

I know MAX and I know he'll do you right. By the way do not submerge the float
in hot water....luke warm is sufficient....hats off to '51 MERC -CT
J B Weld is good stuff but in this situation I would not do it.


Charlie ny
Although MAX may do him right, to get him to the car show would it work to:

Do the water test to locate the hole and attempt to solder it? But use warm water NOT hot as to not cause the fuel inside to expand and Explode!

Once the pin hole is located, drill it out with the tiniest drill bit you got to drain the fuel before soldering.

Re check again after repair to ensure its sealed.
__________________
Sometimes, ingenuity gets in the way of sense and sanity.
Will D is offline   Reply With Quote
Old 03-04-2021, 01:10 PM   #26
51 MERC-CT
Senior Member
 
51 MERC-CT's Avatar
 
Join Date: May 2010
Location: East Hartford, Ct
Posts: 5,898
Default Re: carb leaking gas, what did I do wrong?

Sponsored Links (Register now to hide all advertisements)
If you can determine the area of the crack or pinhole, it can be fixed buy drilling appox. 3/32" holes to let the gas drain and then set aside in a warm area to allow the gas to evaporate. Occasional use of compressed air will help
(don't apply air pressure to the float).
You can tell if the evaporation is sufficient by smelling it.
Then it's just a matter of soldering to seal.
Have done several in this manner with success.
__________________
DON'T RECALL DOING SOMETHING FOR MYSELF BASED ON SOMEONE ELSE'S LIKES OR DISLIKES

Last edited by 51 MERC-CT; 03-04-2021 at 01:22 PM.
51 MERC-CT is offline   Reply With Quote
Old 03-04-2021, 02:40 PM   #27
uncle max
Senior Member
 
uncle max's Avatar
 
Join Date: May 2010
Location: SLC Utah
Posts: 798
Default Re: carb leaking gas, what did I do wrong?

Just tuned in to all of this; been off doing taxes preparing for my CPA (Cleaning, Pressing and Alterations!) for nearly a week...
New float, pin and gaskets headed for Texas in 15 minutes.
Did I say I'm sorry.
__________________
RIP Tyler... My Son, Helper & Best Friend.
Feb '78 to Father's Day '10.
www.97-express.com ~ [email protected]
uncle max is offline   Reply With Quote
Old 03-04-2021, 03:22 PM   #28
V8COOPMAN
Senior Member
 
V8COOPMAN's Avatar
 
Join Date: May 2010
Location: East Shore of LAKE HOUSTON
Posts: 11,106
Default Re: carb leaking gas, what did I do wrong?

Quote:
Originally Posted by uncle max View Post
Just tuned in to all of this; been off doing taxes preparing for my CPA (Cleaning, Pressing and Alterations!) for nearly a week...
New float, pin and gaskets headed for Texas in 15 minutes.
Did I say I'm sorry.

Is THIS place GREAT.....or what? DD
__________________
Click Links Below __


'35-'36 W/8BA & MECHANICAL FAN


T5 W/TORQUE TUBE
V8COOPMAN is offline   Reply With Quote
Old 03-04-2021, 05:51 PM   #29
jason78613
Junior Member
 
jason78613's Avatar
 
Join Date: Oct 2020
Location: Cedar Park, TX
Posts: 20
Default Re: carb leaking gas, what did I do wrong?

This truly is an awesome forum! With all the help and additional searches through previous posts, I feel like I got a solid crash course in carburetors!

As Max mentioned, he reached out and will be sending a new float, much appreciated!

As for the car show this weekend, I followed Will D's instructions and drained the gas through tiny drilled holes and then soldered them up. Then did the hot water test and no bubbles! Took a test drive and it runs fine (I think I just need to adjust the idle screws to get a smoother ride). I don’t trust my soldering skills 100% so this is definitely a temporary solution until Max’s new float arrives.

Thank you so much to everyone!
jason78613 is offline   Reply With Quote
Old 03-04-2021, 05:55 PM   #30
JayChicago
Senior Member
 
JayChicago's Avatar
 
Join Date: Jan 2019
Location: Chicago
Posts: 711
Default Re: carb leaking gas, what did I do wrong?

Quote:
Originally Posted by V8COOPMAN View Post
Is THIS place GREAT.....or what? DD
Absolutely! We have some great guys helping us in this hobby.
JayChicago is offline   Reply With Quote
Old 03-04-2021, 06:19 PM   #31
VeryTangled
Senior Member
 
VeryTangled's Avatar
 
Join Date: May 2010
Location: (Not far enough...) Outside of DC
Posts: 3,386
Default Re: carb leaking gas, what did I do wrong?

And ladies and gentlemen, this is why you use the incredibly awesome vendors who populate this forum.

Over the last dozen years I've got experience with Uncle Max taking a very stinky leaking filthy carb and making it showroom for my '35.

And Charlie has his fingerprints all over my '36 Phaeton (trans, rear, carb, steering, FP, and more).

They are very high on the list of people who get my business so I can get back to driving and smiling!

Their messages here are totally typical of how they handle things.
__________________
-Jeff H

Have you thought about supporting the Early Ford V-8 Foundation Museum?

Last edited by VeryTangled; 03-04-2021 at 06:24 PM.
VeryTangled is offline   Reply With Quote
Old 03-04-2021, 08:19 PM   #32
scicala
Senior Member
 
scicala's Avatar
 
Join Date: Jun 2010
Location: Detroit suburb, MI
Posts: 3,697
Default Re: carb leaking gas, what did I do wrong?

Quote:
Originally Posted by moefuzz View Post
.Your fuel pump is mechanical or electric?

The original mechanical fuel pump on top of your intake may be pushing to much pressure.

Your carb is not designed to handle over pressure for very long and can be over
powered by the fuel pump in a matter of seconds, minutes or hours...
...until it can't physically hold back the excess pressure anymore and it will finally give up.


Quick and easy fix=


You can add an extra gasket (or 2) underneath the fuel pump stand at the intake,

this has the effect of shortening the fuel pump pushrod and will decrease fuel pump pressure somewhat.

The longer the fuel pump pushrod "appears" in relation to the physical height to were it is mounted dictates fuel pressure.


So Hypothetically, if you (don't do it!) were to grind the fuel pump push rod a 1/16th or an 1/8th inch, it would have a shorter stroke and would not push the pump as far or as hard.

Adding an extra gasket under the fuel pump stand at the intake
has the effect of shortening the rod and lowering fuel pump pressure.
You can add one or 2 extra gaskets and experiment.

Don't ever grind the fuel pump pushrod to lower fuel pressure or push or stroke at the fuel pump as this is not easily reversible and over time the mechanical fuel pump looses some of it's pressure at which point you can always pull one of the extra gaskets out.

Also, there are 2 different fuel pump pushrods lengths depending on your intake.

Check that yours is close to the below specs dependent upon aluminum or cast intake manifold.

52-9400-A Push Rod - Fuel Pump (V8-60hp) - Alum. Intake (5.625")

52-9400-B Push Rod - Fuel Pump (V8-60hp) - Cast Iron (6.375")



Back in the old days gaskets were relatively thick,
now a days gaskets are less then paper thin so you may have
inadvertently/unknowingly "adjusted" the fuel pump pressure
upwards by installing a paper thin gasket and you wouldn't
even know it until the needle and seat (float) are
over powered and flooding happens..


Extra gaskets are cheap,

...Cheap enough to buy a couple and still have money for your morning donut






.

Read post #5.

Sal
scicala is offline   Reply With Quote
Old 03-05-2021, 07:14 AM   #33
glennpm
Senior Member
 
glennpm's Avatar
 
Join Date: Sep 2014
Location: Wiscasset, Maine
Posts: 1,965
Default Re: carb leaking gas, what did I do wrong?

Quote:
Originally Posted by V8COOPMAN View Post
Is THIS place GREAT.....or what? DD



Yes it is!
glennpm is online now   Reply With Quote
Old 03-05-2021, 12:17 PM   #34
TJ
Senior Member
 
TJ's Avatar
 
Join Date: May 2010
Location: Napa,California
Posts: 6,005
Default Re: carb leaking gas, what did I do wrong?

It definitely is a great place. You never get too old to learn.
TJ is offline   Reply With Quote
Old 03-06-2021, 10:08 PM   #35
aussie merc
Senior Member
 
aussie merc's Avatar
 
Join Date: Sep 2016
Location: sydney australia
Posts: 1,025
Default Re: carb leaking gas, what did I do wrong?

float level or pump pressure out of curiosity did you run the eng around 1500 rpm have seen fuel pump pressure climb dramatically above 1000 rpm
aussie merc is offline   Reply With Quote
Old 03-06-2021, 10:12 PM   #36
JSeery
Member Emeritus
 
JSeery's Avatar
 
Join Date: Nov 2012
Location: Wichita KS
Posts: 16,132
Default Re: carb leaking gas, what did I do wrong?

Quote:
Originally Posted by aussie merc View Post
float level or pump pressure out of curiosity did you run the eng around 1500 rpm have seen fuel pump pressure climb dramatically above 1000 rpm
See post #5.
JSeery is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 09:49 AM.