Go Back   The Ford Barn > General Discussion > Model A (1928-31)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 10-01-2020, 06:41 AM   #1
Steve Rinaldo
Member
 
Join Date: May 2010
Posts: 89
Default Radius Ball Service

I have just finished doing a service on my 1930. One of the things I did was to tighten up the two radius ball nuts. I checked a lot of the books and previous post about the proper procedure and found a bunch of ways to do it.. The reason for this was I had a slight steering wheel shake between 50-55 mph. I tightened the nuts until they hit the sleeve and then backed them off until I could insert the cotter pin. I drove the car and the shake was gone. My question, is the procedure that I used the normal one that is used?
Thanks, Steve
Steve Rinaldo is offline   Reply With Quote
Old 10-01-2020, 07:14 AM   #2
1931 flamingo
Senior Member
 
1931 flamingo's Avatar
 
Join Date: May 2010
Location: new britain,ct 06052
Posts: 9,387
Default Re: Radius Ball Service

If it worked I wouldn't worry about it...............
Paul in CT
1931 flamingo is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 10-01-2020, 09:13 AM   #3
BRENT in 10-uh-C
Senior Member
 
BRENT in 10-uh-C's Avatar
 
Join Date: May 2010
Location: Eastern Tennessee
Posts: 11,466
Default Re: Radius Ball Service

Quote:
Originally Posted by 1931 flamingo View Post
If it worked I wouldn't worry about it...............
Paul in CT
Until it cracks/breaks the bottom of the clutch housing case.

There is a lot that is assumed in this area. If the radius rod ball is worn out of the 1.500" diameter, tightening seems the prudent thing to do however the fall grows in diameter as the radius rod is rotated. Overtightening allows the radius rod ball to potentially bind during the front-end travel arc. Hit a drastic bump with the cap overtightened and I have seen it where the housing was crack damaged.
__________________
.

BRENT in 10-uh-C
.
www.model-a-ford.com
...(...Finally Updated!! )

.
BRENT in 10-uh-C is offline   Reply With Quote
Old 10-01-2020, 10:15 AM   #4
Benson
Senior Member
 
Join Date: May 2010
Posts: 2,577
Default Re: Radius Ball Service

[qu

Last edited by Benson; 10-06-2020 at 10:07 AM.
Benson is offline   Reply With Quote
Old 10-01-2020, 11:26 AM   #5
midgetracer
Senior Member
 
midgetracer's Avatar
 
Join Date: May 2010
Location: Bismarck ND
Posts: 1,189
Default Re: Radius Ball Service

If the rubber ball is such a poor fix, how come Ford used in the later models?
midgetracer is offline   Reply With Quote
Old 10-01-2020, 11:52 AM   #6
Benson
Senior Member
 
Join Date: May 2010
Posts: 2,577
Default Re: Radius Ball Service

Sponsored Links (Register now to hide all advertisements)
Quote:
Originally Posted by midgetracer View Post
If the rubber ball is such a poor fix, how come Ford used in the later models?
Because in the thirties they had real rubber which lasted much longer when soaked in oil.

All I know is that the ones I tried in the 60's turned to mush in short order.

And all of the restoration shops that I worked at refused to install the rubber ball ... too many "comebacks" don't ya know?

Last edited by Benson; 10-01-2020 at 12:29 PM.
Benson is offline   Reply With Quote
Old 10-01-2020, 11:58 AM   #7
BRENT in 10-uh-C
Senior Member
 
BRENT in 10-uh-C's Avatar
 
Join Date: May 2010
Location: Eastern Tennessee
Posts: 11,466
Default Re: Radius Ball Service

Quote:
Originally Posted by Benson View Post
Because they had real rubber which lasted much longer.
Yes, there are two major differences. Natural rubber and the durometer of the Ford manufactured ball versus the off-shore based rubber.
__________________
.

BRENT in 10-uh-C
.
www.model-a-ford.com
...(...Finally Updated!! )

.
BRENT in 10-uh-C is offline   Reply With Quote
Old 10-01-2020, 12:08 PM   #8
Benson
Senior Member
 
Join Date: May 2010
Posts: 2,577
Default Re: Radius Ball Service

The offshore people who made the rubber balls in the 60s 70s and 80s were most likely using the same rubber that they later used to make the inner tubes of 10 -15 years ago and some of us know how that turned out!

Last edited by Benson; 10-02-2020 at 12:38 PM.
Benson is offline   Reply With Quote
Old 10-01-2020, 02:06 PM   #9
1930-Pickup
Senior Member
 
Join Date: Mar 2017
Location: southern California
Posts: 725
Default Re: Radius Ball Service

Why does no one make a polyurethane ball with an engineered durometer?
__________________
"That's my wild unsubstantiated guess, and I'm sticking to it regardless of the facts!"
1930-Pickup is offline   Reply With Quote
Old 10-01-2020, 04:45 PM   #10
mhsprecher
Senior Member
 
mhsprecher's Avatar
 
Join Date: Aug 2012
Location: Takoma Park, MD
Posts: 2,809
Default Re: Radius Ball Service

Brent's tip is a very valuable bit of information!
__________________
1924 Model T Coupe
1928 Model A Roadster
1930 Model A Town Sedan
1939 Deluxe Fordor
1945 pickup
1951 Custom convertible
mhsprecher is offline   Reply With Quote
Old 10-01-2020, 06:38 PM   #11
Steve Rinaldo
Member
 
Join Date: May 2010
Posts: 89
Default Re: Radius Ball Service

I forgot to mention that my setup does not have a rubber ball and it does have the springs. Steve
Steve Rinaldo is offline   Reply With Quote
Old 10-03-2020, 05:43 AM   #12
Jacksonlll
Senior Member
 
Jacksonlll's Avatar
 
Join Date: Jul 2012
Location: Michigan-- Member of Oakleaf of MARC
Posts: 1,686
Send a message via ICQ to Jacksonlll
Default Re: Radius Ball Service

Her is a video I did with a camer under the car. It's rough, but it shows a little of what goes on under there.
https://www.youtube.com/watch?v=ry29...cz4R0&index=56
Jacksonlll is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 06:36 AM.