|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
05-20-2014, 12:24 PM | #1 |
Senior Member
Join Date: May 2010
Location: Michigan
Posts: 171
|
POR UV Sensitivity.....what happens
I need to paint a steel handrail for my parents porch and want to know what will happen to the POR as it is outside in direct sunlight??
I know this is not car related but they can not get up and down the steps anymore and I want to do the job once and do it right. Thanks Z |
05-20-2014, 12:29 PM | #2 |
Senior Member
Join Date: May 2010
Location: Napanee ontario Canada
Posts: 395
|
Re: POR UV Sensitivity.....what happens
My son painted a steel deck on a flatbed snowmobile trailer and it just went dull and powdery ...almost like flat black in no time...I would find something else if I were you...Good luck
|
Sponsored Links (Register now to hide all advertisements) |
|
05-20-2014, 12:34 PM | #3 |
Senior Member
Join Date: May 2010
Location: shirley ny
Posts: 992
|
Re: POR UV Sensitivity.....what happens
rustoleum is very good and lasts
|
05-20-2014, 12:52 PM | #4 |
Senior Member
Join Date: May 2010
Location: so cal, placerville, vegas
Posts: 1,394
|
Re: POR UV Sensitivity.....what happens
I did a lot of my 34 body in POR-15, the underside, inside, and other places, but NOT the exterior surface. As noted above, it doesn't hold up - turns dull, and chalks. Check the directions - I think it was supposed to be covered with another coat of 'something'. In any event, I'm with oldskool, I think rustoleum is a much better product for durability and holding its look.
BTW... POR makes more than one material. Above comment is directed towards the original POR-15 - paint-it-over-any-old-rusted-metal. As an example of another POR material, I've used POR-15 Engine Enamel on a few engines - and it is an excellent product that is holding up well. JMO Last edited by bobH; 05-20-2014 at 01:56 PM. |
05-20-2014, 01:03 PM | #5 |
Senior Member
Join Date: May 2010
Location: Mn
Posts: 2,410
|
Re: POR UV Sensitivity.....what happens
Get a number, and call POR15, and talk to one of their tecs.
POR15 makes a real durable clearcoat to go on bare aluminum. POR15 Does NOT make a clearcoat to go over the initial groundcoat, but they DO make single part or 2 part gloss coatings to spray over the original POR15 groundcoat, for UV protection. .
__________________
If mama ain't happy, ain't nobody happy. But if daddy ain't happy...RUN |
05-20-2014, 01:26 PM | #6 |
Senior Member
Join Date: May 2010
Location: Michigan
Posts: 171
|
Re: POR UV Sensitivity.....what happens
Sponsored Links (Register now to hide all advertisements)
Z |
05-20-2014, 01:33 PM | #7 |
Senior Member
Join Date: May 2010
Location: N.W.England
Posts: 439
|
Re: POR UV Sensitivity.....what happens
That's great! I just spent the day prepping and painting a new front axle ,steering arms,spindles and a few other bits with POR 15......I though it was supposed to be the best thing since sliced bread.....now it looks like I'll have to paint it over with another paint.
I took really good care not to get it on my hands as it takes days to wear off.....my wife came home and told me I have some paint on my nose....they are right, it does not come off! |
05-20-2014, 01:51 PM | #8 |
Senior Member
Join Date: Jul 2010
Posts: 2,593
|
Re: POR UV Sensitivity.....what happens
I think you'll be ok with your front end stuff, ifs all underneath, not in direct sun light.
Martin. |
05-20-2014, 02:17 PM | #9 |
Member
Join Date: Dec 2012
Location: Lubbock Texas
Posts: 70
|
Re: POR UV Sensitivity.....what happens
Tractor implement paint from Tractor Supply is good and is uv and chemical resistant
|
05-20-2014, 04:34 PM | #10 |
Senior Member
Join Date: Jun 2013
Location: home of the REDS
Posts: 392
|
Re: POR UV Sensitivity.....what happens
por 15 is a rust primer, not good in uv rays,, good underhood , underside,, they make a top coat for it,,, has to dry a few hrs , then put their top coat on it for uv protection,,,
|
05-20-2014, 05:07 PM | #11 |
Member
Join Date: Jul 2012
Location: Tuttle, OK
Posts: 64
|
Re: POR UV Sensitivity.....what happens
What is recommended with POR 15 is to put a good coat of your favorite primer over the stillwet or at least tacky por 15. Has to at least be tacky or it won't stick. Then you can paint over the primer whenever you want. If you try to paint over dry por15 it won't stick. It is great stuff.
|
05-20-2014, 05:32 PM | #12 |
Senior Member
Join Date: Feb 2011
Location: Arlington, Texas
Posts: 379
|
Re: POR UV Sensitivity.....what happens
Hammer tone does good outside. Spray are brush on.
|
05-20-2014, 06:01 PM | #13 |
Senior Member
Join Date: May 2010
Location: Iowa
Posts: 178
|
Re: POR UV Sensitivity.....what happens
Por-15 will become chalky and will make your hand turn black.
|
05-21-2014, 09:43 PM | #14 | |
Senior Member
Join Date: May 2010
Location: New Jersey
Posts: 832
|
Re: POR UV Sensitivity.....what happens
Quote:
My friend painted his frame with it and left it outside. When I stopped back over his house a week or two later it looked like it had been done years ago. When they say it doesn't like sun they mean it. |
|
05-22-2014, 07:29 PM | #15 |
Senior Member
Join Date: May 2010
Posts: 2,871
|
Re: POR UV Sensitivity.....what happens
A far better product is SEM "Rust Shield". The SEM product is UV resistant when you use the catalyst with it. I have used POR-15 , under cars, but it does not seem to stand up, and it also hardens and goes bad once some air gets to it, and is mess to work with.
|
05-23-2014, 03:15 AM | #16 |
Senior Member
Join Date: Jul 2011
Location: Deerfield N.H.
Posts: 294
|
Re: POR UV Sensitivity.....what happens
Thumbs up for the rust shield. It is a one step product requiring less labor .
|
05-23-2014, 07:47 AM | #17 |
Member
Join Date: May 2010
Location: Benton Arkansas
Posts: 60
|
Re: POR UV Sensitivity.....what happens
Powder coating can be a solution but not all PC colors will stand UV's either.
|
05-23-2014, 09:02 AM | #18 |
Senior Member
Join Date: Nov 2010
Location: Lancaster PA
Posts: 531
|
Re: POR UV Sensitivity.....what happens
If you let POR 15 get chalky, then paint over it, will the paint stay on?
To store POR15 I put it in a glass jar, and fill the top of the jar with argon or CO2 from my welder before I tighten the cap - works great. |
05-23-2014, 10:16 AM | #19 | |
Senior Member
Join Date: May 2010
Location: Oakdale,Ca
Posts: 1,323
|
Re: POR UV Sensitivity.....what happens
Quote:
When I built hand rails for my folks, I used 3/4in (maybe it was 1/2inch) galvanized pipe and my trusty HF pipe bender...where I attached it to the cement, I threaded it and used a floor flange, masonary bit and those "expanding" things you knock into the hole and thread into...not the plastic ones, but steel ones. |
|
05-23-2014, 12:56 PM | #20 |
Senior Member
Join Date: May 2010
Location: Central Iowa
Posts: 691
|
Re: POR UV Sensitivity.....what happens
No. The top coat would need a good base to build upon. Chalky paint, regardless of type (regular paint, powder coat, POR15, etc), is not a good base.
__________________
Mike Wanted: - '32-34 Open Cab Pickup (RPU) parts and documents/articles/info - ARDUN parts |
05-23-2014, 06:42 PM | #21 |
Senior Member
Join Date: May 2010
Location: Santee, California
Posts: 3,505
|
Re: POR UV Sensitivity.....what happens
I've been successful in getting a powder coat like finish by using POR15. I then gently scuff the POR15 with a scotch brite, then top coat with Rustoleum Professional Black. What I love about the POR15 is how well it will level on any surface. Unlike other finishes that mold to every minor blemish under it, the POR15 flows to a perfect level finish due to the long cure and flow time. I have had no paint lifting problems, and it's durable.
|
|
|
Sponsored Links (Register now to hide all advertisements) |
|