|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
04-25-2021, 12:59 PM | #1 |
Senior Member
Join Date: May 2010
Location: Dallas
Posts: 583
|
Head Bolt continually weeping
Painted the heads, installed stainless bolts, torqued bolts to 60 and a few will not stop weeping. Any suggestions of how I may stop these annoying leaks?
|
04-25-2021, 01:39 PM | #2 |
Senior Member
Join Date: May 2010
Location: Coral Springs FL
Posts: 10,949
|
Re: Head Bolt continually weeping
Doesn't look like you have installed ss bolts as your photo shows studs.
You will probably have to remove the stud and reseal it. I would be hesitant to use stainless bolts as they may not be able to withstand the torque required. Here's a good thread. https://www.fordbarn.com/forum/showt...ad+bolt+torque Last edited by 19Fordy; 04-25-2021 at 01:45 PM. |
Sponsored Links (Register now to hide all advertisements) |
|
04-25-2021, 01:42 PM | #3 |
Senior Member
Join Date: Nov 2010
Location: Beamsville,Ontario,Canada
Posts: 482
|
Re: Head Bolt continually weeping
Put some thread sealer, I like Loctite PST, on the fine threads, re-install the head nuts and retorque.
|
04-25-2021, 02:23 PM | #4 |
Senior Member
Join Date: May 2010
Location: Above the gnat line in Georgia
Posts: 7,009
|
Re: Head Bolt continually weeping
It will stop eventually but heed the advice given above.
__________________
Life is like a roll of toilet paper. The closer to the end, the faster it goes. It is better to be seen, than viewed. "We sleep safe in our beds because rough men stand ready in the night to visit violence on those who would do us harm". |
04-25-2021, 03:18 PM | #5 |
Senior Member
Join Date: May 2010
Posts: 2,173
|
Re: Head Bolt continually weeping
Don't seem like much of a leak. If it were mine, I'd leave it alone. I agree with Lawson. It might eventually stop all by itself. Jack E/NJ
|
04-25-2021, 03:43 PM | #6 |
Senior Member
Join Date: May 2010
Location: Santee, California
Posts: 3,505
|
Re: Head Bolt continually weeping
Sponsored Links (Register now to hide all advertisements)
Last edited by Russ/40; 04-25-2021 at 06:13 PM. |
04-25-2021, 04:36 PM | #7 |
Senior Member
Join Date: May 2012
Location: Queensland, Australia
Posts: 10,372
|
Re: Head Bolt continually weeping
Water continually weeping from one stud on 1935 Ford V8 engine. |
04-25-2021, 04:41 PM | #8 |
Senior Member
Join Date: May 2010
Location: upstate SC
Posts: 2,964
|
Re: Head Bolt continually weeping
leak is really coming from the threads on the stud, one a new stud installation I use permatex #2 non hardening on the studs. only way to seal the studs is from the water jacket side. on a problem like this I use the old style pellet stop leak from barrs, put it in run the engine until hot and then stop the engine and drain out all the coolant and barrs leak. save it for now, leave over night then fill up with water and run engine. I have had to run the solution thru a couple of times to make them stop. then drain and refill with your antifreeze
|
04-25-2021, 05:06 PM | #9 |
Member
Join Date: Dec 2020
Location: Ellensburg wa
Posts: 58
|
Re: Head Bolt continually weeping
I have used alumaseal with success. I would try some kind of stop leak before retorking the heads.
|
04-25-2021, 05:46 PM | #10 |
Senior Member
Join Date: May 2010
Location: Dallas
Posts: 583
|
Re: Head Bolt continually weeping
When applying the silicone on the head bolt do I need to drain all antifreeze...you cant just silicone and put back into the greasy antifreeze filled whole or can you?
|
04-25-2021, 06:17 PM | #11 |
Senior Member
Join Date: May 2010
Posts: 2,173
|
Re: Head Bolt continually weeping
guy1unico>>>When applying the silicone on the head bolt do I need to drain all antifreeze.>>>
Sorry, you can't apply anything to the head bolts in your situation. Jack E/NJ |
04-25-2021, 08:31 PM | #12 |
Member Emeritus
Join Date: Nov 2012
Location: Wichita KS
Posts: 16,132
|
Re: Head Bolt continually weeping
Maybe it is just terminology, but you keep saying bolts but the photo you posted shows studs with nuts. The only options you have without pulling the studs is a sealer in the coolant. Increasing the torque on the nuts does nothing at all as far as sealing the leaks goes. It is leaking through the threads on the studs in the block. You can pull the studs and seal them better or use a sealant.
|
04-25-2021, 08:38 PM | #13 | |
Senior Member
Join Date: Dec 2013
Location: Minnesota, Florida Keys
Posts: 10,319
|
Re: Head Bolt continually weeping
Quote:
|
|
04-25-2021, 08:40 PM | #14 |
Member
Join Date: Oct 2018
Location: Aliaga,Turkey
Posts: 77
|
Re: Head Bolt continually weeping
It most likely will stop weeping on its own, but you can put a little bars leak powder in the radiator if it bothers you.
__________________
"Sometimes he would accuse chestnuts of being lazy, the sort of general malaise that only the genius possess and the insane lament." |
04-25-2021, 09:17 PM | #15 |
Member Emeritus
Join Date: Nov 2012
Location: Wichita KS
Posts: 16,132
|
Re: Head Bolt continually weeping
|
04-25-2021, 09:41 PM | #16 |
Senior Member
Join Date: May 2010
Location: upstate SC
Posts: 2,964
|
Re: Head Bolt continually weeping
yeah, rust will eventually seal the threads
|
04-26-2021, 06:28 AM | #17 |
Member
Join Date: Dec 2018
Location: Oakdale, Ca
Posts: 44
|
Re: Head Bolt continually weeping
Seems it may be a fresh engine, shouldn’t be tough to remove the studs. Are those studs SS? The nuts look like they are, but the studs have a dull iron look to them?
|
04-26-2021, 11:23 AM | #18 |
Senior Member
Join Date: Mar 2014
Location: Jacksonville FL
Posts: 3,961
|
Re: Head Bolt continually weeping
First there are many on here more "versed" than me BUT the first "Red Flag" I read is the use of Stainless Steel Nuts........At 60ft/Lbs you are about 24Ft/lbs more than the "generally" accepted torque value for Stainless Steel. I have some SS cap nuts and were advised NOT to use those as a quoted "maximum" torque recommendation was 40ft/Lbs.....I myself would not use ANY Stainless Steel fastener for something critical like head studs and nuts!!!!! JMO
Based on what has been posted, did you heat cycle the heads and arrive at 60???? IF you haven't heat cycled and re checked your torque then you could have one that stretched and now is not at 60Ft/Lbs can of worms now open Last edited by rockfla; 04-26-2021 at 11:55 AM. |
04-26-2021, 12:04 PM | #19 |
Senior Member
Join Date: Oct 2016
Location: harpursville ny
Posts: 1,040
|
Re: Head Bolt continually weeping
Had two studs leaking on my 39 engine, stopped all by itself.
|
04-26-2021, 12:12 PM | #20 |
Senior Member
Join Date: May 2010
Location: Coral Springs FL
Posts: 10,949
|
Re: Head Bolt continually weeping
rockfla is 100% correct about not using stainless nuts and bolts as they shear too easily using the torque required on head bolts. The threads will stretch, especially after repeated use.
|
|
|
Sponsored Links (Register now to hide all advertisements) |
|