Go Back   The Ford Barn > General Discussion > Model A (1928-31)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 03-29-2018, 06:28 PM   #1
Ian in Mississauga
Senior Member
 
Join Date: May 2010
Posts: 136
Default Vacuum gauge reading with a Model B distributor

I always hook up a vacuum gauge at the start of the season as a diagnostic tool. With a model A distributor I get a range of about 16" to 20". Recently I installed a model B distributor. What numbers are normal with this set up?
tia, Ian
Ian in Mississauga is offline   Reply With Quote
Old 03-29-2018, 07:17 PM   #2
Patrick L.
Senior Member
 
Patrick L.'s Avatar
 
Join Date: May 2010
Location: Largo Florida
Posts: 7,225
Default Re: Vacuum gauge reading with a Model B distributor

I don't see where there should be a difference. We're talking about engine condition not ignition system. The base timing is advanced more than an A, thats all.
Patrick L. is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 03-29-2018, 08:40 PM   #3
michael a
Senior Member
 
michael a's Avatar
 
Join Date: Feb 2015
Location: Lone Jack Missouri
Posts: 381
Default Re: Vacuum gauge reading with a Model B distributor

I always set my distributor at the highest point of vacuum this is an FSI unit with flyweight advanced positive High Point at idle

Sent from my SM-J700T using Tapatalk
michael a is offline   Reply With Quote
Old 03-30-2018, 08:49 AM   #4
SeaSlugs
Senior Member
 
SeaSlugs's Avatar
 
Join Date: May 2010
Location: Central, IL
Posts: 3,968
Default Re: Vacuum gauge reading with a Model B distributor

http://www.onallcylinders.com/wp-con...-reading-1.png

invaluable tool. Between a compression tester, leakdown tester, and a vacuum gauge you can tell everything there is to know about any engine and anytime a suspected engine issue, backfiring, overheating, or low power these 3 basic tests should be run. Easily do all 3 in less than an hour.

Link is a great chart you can print off and pin to the garage wall or wrap the vacuum gauge in it.

Model A has an easy access vacuum port right on the manifold so it cant get any easier.
__________________
1929 Model AA - Need long splash aprons!
SeaSlugs is offline   Reply With Quote
Old 03-30-2018, 11:10 AM   #5
Corley
Senior Member
 
Join Date: Aug 2011
Location: Battle Ground WA
Posts: 293
Default Re: Vacuum gauge reading with a Model B distributor

Quote:
Originally Posted by michael a View Post
I always set my distributor at the highest point of vacuum this is an FSI unit with flyweight advanced positive High Point at idle

Sent from my SM-J700T using Tapatalk

Huh? "Splain yourself Lucy?"
Corley is offline   Reply With Quote
Old 03-30-2018, 03:18 PM   #6
100IH
Senior Member
 
Join Date: Dec 2011
Location: SW Idaho
Posts: 970
Default Re: Vacuum gauge reading with a Model B distributor

Sponsored Links (Register now to hide all advertisements)
Comparing distributors is, to me a fuzzy thing because the A with the manual advance will be all over the map for vacuum depending where basic is set and where lever is set. B same thing for basic timing and except for all of the variables in camshaft profile, timing covers and A vs. B block variables and condition of centrifugal timing on B dist. Like comparing track shoes to horse shoes.
I commend your use of the vacuum gauge though.
100IH is offline   Reply With Quote
Old 03-31-2018, 04:12 AM   #7
michael a
Senior Member
 
michael a's Avatar
 
Join Date: Feb 2015
Location: Lone Jack Missouri
Posts: 381
Default Re: Vacuum gauge reading with a Model B distributor

Quote:
Originally Posted by Corley View Post
Huh? "Splain yourself Lucy?"
Have you ever used the vacuum gauge

Sent from my SM-J700T using Tapatalk
michael a is offline   Reply With Quote
Old 03-31-2018, 07:05 AM   #8
Corley
Senior Member
 
Join Date: Aug 2011
Location: Battle Ground WA
Posts: 293
Default Re: Vacuum gauge reading with a Model B distributor

Quote:
Originally Posted by michael a View Post
Have you ever used the vacuum gauge

Sent from my SM-J700T using Tapatalk
Only for the last 60 years or so. (I'm 78 now, been wrenching most of those years.) However, your sentence did not make sense to me. Positive? What's that about??? I've never found highest vacuum reading to be the optimal timing set point. In fact on many engines, timing and vacuum readings are not really related at all, unless timing is way out.

Being a Jr member here does not imply one is new to As or mechanics, only that one tends to not post much.
Corley is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 06:25 AM.