Go Back   The Ford Barn > General Discussion > Model A (1928-31)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 08-06-2020, 10:09 PM   #1
Brendan1959
Member
 
Brendan1959's Avatar
 
Join Date: Jul 2010
Location: Melbourne Australia
Posts: 95
Default Main bearings Babbitt unusual

I pulled down one of my spare motors the main bearings are different to my other motors. Machined groves in the block bearings and none in the caps?
Is this unusual?
Attached Images
File Type: jpg IMG_5704.jpg (33.6 KB, 259 views)
File Type: jpg IMG_5703.jpg (45.5 KB, 244 views)
File Type: jpg IMG_5702.jpg (33.9 KB, 231 views)
File Type: jpg IMG_5700.jpg (41.1 KB, 212 views)
File Type: jpg IMG_5698.jpg (38.7 KB, 201 views)
Brendan1959 is offline   Reply With Quote
Old 08-06-2020, 10:22 PM   #2
Synchro909
Senior Member
 
Synchro909's Avatar
 
Join Date: Jun 2014
Location: Melbourne, Australia
Posts: 7,471
Default Re: Main bearings Babbitt unusual

Although that is not my favourite way of doing it, I've seen bearings like that go for a long time. It is clear that those are not new bearings and that they haven't been a problem so far. The oil flows around the bearing through that groove till it gets to the join between the block and the cap. You'll notice the edges there are chamfered almost right across the bearing. The oil runs along there so you have lubrication right across the bearing surface. More oil on one side than the other but adequate.
That's fine on the front and middle bearing but I like a spiral groove in the rear one to get the oil across the bearing better.
You can add the groove in the top half now if you like.
__________________
I'm part of the only ever generation with an analogue childhood and a digital adulthood.

Last edited by Synchro909; 08-07-2020 at 12:01 AM.
Synchro909 is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 08-06-2020, 11:21 PM   #3
Jack Shaft
BANNED
 
Join Date: Dec 2019
Posts: 1,196
Default Re: Main bearings Babbitt unusual

Those bearings will work well,oil is carried through the bearing by hydrodynamic theory and the turning crankshaft,the crankshaft is supported by a thin filmof oil,which flows as the crankshaft turns.
Jack Shaft is offline   Reply With Quote
Old 08-07-2020, 04:46 AM   #4
Werner
Senior Member
 
Werner's Avatar
 
Join Date: Jan 2019
Location: Germany, near Aachen
Posts: 1,151
Default Re: Main bearings Babbitt unusual

Brendan,


I can't say that specifically about the A motor. But in the past it was generally thought that there should be a groove in plain slide bearings in order to transport the lubricating oil.

It was later researched that these grooves disrupt the hydrodynamic lubricating film. Therefore, sliding bearings without a groove in it are used nowadays. That's better.

Perhaps because of this someone used more modern bearing caps on your engine?
__________________
Beste Gruesse aus Deutschland,
Werner


Ford Model A, Roadster, 1928
Citroen 11 CV, 1947
Hercules W 2000, 1976; (with NSU-Wankel Rotary Engine), Canadian version
Werner is offline   Reply With Quote
Old 08-07-2020, 11:01 AM   #5
Jim Brierley
Senior Member
 
Join Date: Jun 2010
Location: Temecula, CA
Posts: 4,066
Default Re: Main bearings Babbitt unusual

Looks like that block was set up for full pressure oiling, with a drilled crank for oil to the rods.
Jim Brierley is offline   Reply With Quote
Old 08-08-2020, 12:02 AM   #6
Chuck Sea/Tac
Senior Member
 
Chuck Sea/Tac's Avatar
 
Join Date: May 2010
Location: Between Seattle & Tacoma
Posts: 2,351
Default Re: Main bearings Babbitt unusual

Sponsored Links (Register now to hide all advertisements)
Quote:
Originally Posted by Jim Brierley View Post
Looks like that block was set up for full pressure oiling, with a drilled crank for oil to the rods.
My thought as well.
Chuck Sea/Tac is offline   Reply With Quote
Old 08-08-2020, 01:26 AM   #7
Brendan1959
Member
 
Brendan1959's Avatar
 
Join Date: Jul 2010
Location: Melbourne Australia
Posts: 95
Default Re: Main bearings Babbitt unusual

Quote:
Originally Posted by Jim Brierley View Post
Looks like that block was set up for full pressure oiling, with a drilled crank for oil to the rods.
The crank is not drilled, I am hopeful this block can be used with these bearings, its a shame the crank has a little rust and some minor pitting, I think this one was stored outside for a while. I have a couple of cranks, perhaps one can be ground to fit. I only have a vernier, so I have ordered a micrometer so I can measure properly. The last picture of the rear-main almost looks like an insert.
The rods have a similar grove, but in the cap and rod.

Its got one x rod as well.

Jim
I have your book and have read it again while in isolation, a good read.

Brendan
Attached Images
File Type: jpg IMG_5708.jpg (27.4 KB, 93 views)
File Type: jpg IMG_5707.jpg (38.1 KB, 88 views)
Brendan1959 is offline   Reply With Quote
Old 08-08-2020, 05:39 AM   #8
Synchro909
Senior Member
 
Synchro909's Avatar
 
Join Date: Jun 2014
Location: Melbourne, Australia
Posts: 7,471
Default Re: Main bearings Babbitt unusual

Some minor pitting on the journals won't do any harm. They act as an oil reservoir. The journal and the babbit should never come into contact with each other anyway.
__________________
I'm part of the only ever generation with an analogue childhood and a digital adulthood.
Synchro909 is offline   Reply With Quote
Old 08-09-2020, 01:58 AM   #9
Brendan1959
Member
 
Brendan1959's Avatar
 
Join Date: Jul 2010
Location: Melbourne Australia
Posts: 95
Default Re: Main bearings Babbitt unusual

https://www.youtube.com/watch?v=a8mx...ature=youtu.be

https://www.youtube.com/watch?v=6k3o...ature=youtu.be

Thought I would try cleaning up the crank in my lathe.
Brendan1959 is offline   Reply With Quote
Old 08-09-2020, 10:45 AM   #10
Russ/40
Senior Member
 
Russ/40's Avatar
 
Join Date: May 2010
Location: Santee, California
Posts: 3,505
Default Re: Main bearings Babbitt unusual

Quote:
Originally Posted by Brendan1959 View Post
Clever approach, very high tech, and very functional. LOL
Russ/40 is offline   Reply With Quote
Old 08-10-2020, 02:04 AM   #11
Richard in Anaheim CA
Senior Member
 
Richard in Anaheim CA's Avatar
 
Join Date: May 2010
Location: Anaheim California
Posts: 551
Default Re: Main bearings Babbitt unusual

Don't turn it in your lathe, just polish it with crocus cloth if the journals are round
Richard in Anaheim CA is offline   Reply With Quote
Old 08-10-2020, 06:38 PM   #12
Brendan1959
Member
 
Brendan1959's Avatar
 
Join Date: Jul 2010
Location: Melbourne Australia
Posts: 95
Default Re: Main bearings Babbitt unusual

After cleaning up the crank i tested with plasti gauge front and center 2 thou, rear about 6 thou.
Block seems standard size ( I have a bore gauge coming).
I have also ordered a Lisle micrometer hone. Apparently they work well and can hone to next oversize.
Attached Images
File Type: jpg Hone.jpg (37.7 KB, 36 views)
Brendan1959 is offline   Reply With Quote
Old 08-10-2020, 06:49 PM   #13
Synchro909
Senior Member
 
Synchro909's Avatar
 
Join Date: Jun 2014
Location: Melbourne, Australia
Posts: 7,471
Default Re: Main bearings Babbitt unusual

Have you considered taking 4 thou worth of shims out of the rear bearing and calling it good?
__________________
I'm part of the only ever generation with an analogue childhood and a digital adulthood.
Synchro909 is offline   Reply With Quote
Old 08-10-2020, 08:34 PM   #14
Brendan1959
Member
 
Brendan1959's Avatar
 
Join Date: Jul 2010
Location: Melbourne Australia
Posts: 95
Default Re: Main bearings Babbitt unusual

Quote:
Originally Posted by Synchro909 View Post
Have you considered taking 4 thou worth of shims out of the rear bearing and calling it good?
That is the plan!
Brendan1959 is offline   Reply With Quote
Old 08-17-2020, 09:27 PM   #15
Brendan1959
Member
 
Brendan1959's Avatar
 
Join Date: Jul 2010
Location: Melbourne Australia
Posts: 95
Default Re: Main bearings Babbitt unusual

Modified dipper pan, I wonder what made them do do this?
Attached Images
File Type: jpg IMG_5728.jpg (40.8 KB, 79 views)
Brendan1959 is offline   Reply With Quote
Old 08-17-2020, 10:56 PM   #16
Synchro909
Senior Member
 
Synchro909's Avatar
 
Join Date: Jun 2014
Location: Melbourne, Australia
Posts: 7,471
Default Re: Main bearings Babbitt unusual

Over the years, there have been all sorts of screwball ideas about how to improve the dipper tray. That is no doubt one of them. I've even seen holes drilled in the bottom of the tray. I think that was done so that ALL of the oil would be removed when the sump is drained for a service and no old oil will contaminate the new. Pity about the big ends running dry on every start up!
Who knows what they were thinking. I'd just weld up those holes and use that tray.
__________________
I'm part of the only ever generation with an analogue childhood and a digital adulthood.
Synchro909 is offline   Reply With Quote
Old 08-18-2020, 02:23 PM   #17
BRENT in 10-uh-C
Senior Member
 
BRENT in 10-uh-C's Avatar
 
Join Date: May 2010
Location: Eastern Tennessee
Posts: 11,485
Default Re: Main bearings Babbitt unusual

Quote:
Originally Posted by Brendan1959 View Post
Modified dipper pan, I wonder what made them do do this?
Quote:
Originally Posted by Synchro909 View Post
Over the years, there have been all sorts of screwball ideas about how to improve the dipper tray. That is no doubt one of them. I've even seen holes drilled in the bottom of the tray. I think that was done so that ALL of the oil would be removed when the sump is drained for a service and no old oil will contaminate the new. Pity about the big ends running dry on every start up!
Who knows what they were thinking. I'd just weld up those holes and use that tray.

Look again. The holes are not affecting the oil levels in the dipper sump. Whatever amount of oil that was in the sump when the engine stopped rotating is the level that would have been there during start-up. Therefore the rods would not have been dry when the engine was started.
__________________
.

BRENT in 10-uh-C
.
www.model-a-ford.com
...(...Finally Updated!! )

.
BRENT in 10-uh-C is offline   Reply With Quote
Old 08-18-2020, 09:05 PM   #18
Synchro909
Senior Member
 
Synchro909's Avatar
 
Join Date: Jun 2014
Location: Melbourne, Australia
Posts: 7,471
Default Re: Main bearings Babbitt unusual

Quote:
Originally Posted by BRENT in 10-uh-C View Post
Look again. The holes are not affecting the oil levels in the dipper sump. Whatever amount of oil that was in the sump when the engine stopped rotating is the level that would have been there during start-up. Therefore the rods would not have been dry when the engine was started.
Brent, my comment was referring to the example I had just given about holes in the bottom of the dipper tray - not the ones in the picture. With holes in the bottom, the oil drained out very quickly so the rods ran dry till oil filled everything up again.
__________________
I'm part of the only ever generation with an analogue childhood and a digital adulthood.
Synchro909 is offline   Reply With Quote
Old 08-18-2020, 10:16 PM   #19
johnneilson
Senior Member
 
Join Date: Jun 2010
Location: 34.22 N 118.36 W
Posts: 1,044
Default Re: Main bearings Babbitt unusual

Quote:
Originally Posted by Synchro909 View Post
Brent, my comment was referring to the example I had just given about holes in the bottom of the dipper tray - not the ones in the picture. With holes in the bottom, the oil drained out very quickly so the rods ran dry till oil filled everything up again.
Or they just stopped turning................
__________________
As Carroll Smith wrote; All Failures are Human in Origin.
johnneilson is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 02:55 PM.