|
Sponsored Links (Register now to hide all advertisements) |
|
|
Thread Tools | Display Modes |
|
07-07-2020, 01:04 PM | #1 |
Senior Member
Join Date: Mar 2019
Location: Sweden
Posts: 145
|
Timing and hand throttle levers
I think I messed up when I refurbished my steering column by removing the hand control levers.
Any good ideas out there on how to get them back in? |
07-07-2020, 03:32 PM | #2 |
Senior Member
|
Re: Timing and hand throttle levers
Sure, you just have to “worry” them in. You will find the hole. Stick with it.
|
Sponsored Links (Register now to hide all advertisements) |
|
07-07-2020, 04:06 PM | #3 |
Senior Member
Join Date: Mar 2019
Location: Sweden
Posts: 145
|
Re: Timing and hand throttle levers
|
07-07-2020, 03:48 PM | #4 |
Senior Member
Join Date: May 2010
Location: on the Littlefield
Posts: 6,159
|
Re: Timing and hand throttle levers
I have drilled a small dimple in the end and used ice pick for guide
|
07-08-2020, 09:53 AM | #5 |
Senior Member
Join Date: Aug 2018
Posts: 2,332
|
Re: Timing and hand throttle levers
In the U.S you could perhaps purchase a good used one from a place like Berts. Since you are in Sweden, this may not be an option.
|
07-09-2020, 04:06 AM | #6 |
Senior Member
Join Date: Mar 2019
Location: Sweden
Posts: 145
|
Re: Timing and hand throttle levers
|
07-08-2020, 10:50 AM | #7 |
Senior Member
Join Date: May 2010
Location: Santee, California
Posts: 3,505
|
Re: Timing and hand throttle levers
The first one should be easy, as you can see down the other hole for guidance. Feel your way around with the second one, and you can tap the installed one to get your orientation for the second. You should be able to feel the second one tapping against the first installed one.
|
07-09-2020, 04:10 AM | #8 | |
Senior Member
Join Date: Mar 2019
Location: Sweden
Posts: 145
|
Re: Timing and hand throttle levers
Quote:
Guess I'll have to pull it out again so I can hold the column in a vertical position instead. |
|
07-09-2020, 07:01 AM | #9 |
Senior Member
Join Date: May 2011
Location: Elyria, Ohio
Posts: 756
|
Re: Timing and hand throttle levers
A few years ago I helped a friend restore a '30 coupe. It went smoothly and it was a good experience until we installed the levers in the steering column.
Marty |
07-09-2020, 07:12 AM | #10 |
Senior Member
Join Date: Apr 2013
Location: Northwest CT
Posts: 1,092
|
Re: Timing and hand throttle levers
Mine were also a bear to get back in. Part of the problem was the new upper bushing... by far the worst part of the entire steering box rebuild.
|
07-09-2020, 07:49 AM | #11 |
BANNED
Join Date: Dec 2019
Posts: 1,196
|
Re: Timing and hand throttle levers
On top of all of the above,be sure and slide a piece of fuel line on the rods as an anti rattler.
Mikko,if your going to run a performance head get rid of the A distributor,go with a mechanical advance unit,the tolerance for timing inaccuracy gets shorter as you raise compression.I run the throttle rod only on mine..its handy for warm up and oklahoma cruise control..but I ditched the spark rod,run a B distributor. |
07-09-2020, 08:49 AM | #12 | |
Senior Member
Join Date: Mar 2019
Location: Sweden
Posts: 145
|
Re: Timing and hand throttle levers
Quote:
|
|
07-09-2020, 08:19 AM | #13 |
Senior Member
Join Date: May 2010
Location: Bismarck ND
Posts: 1,189
|
Re: Timing and hand throttle levers
I find that putting them in with the anti rattler is much easier before you put the column on the steering shaft. Then ou can use the steering shaft hole and a tool to guide the levers into the bottom hole. It may be a pain to disassemble now, but probably save time in the long run and ou can get them in with the anti rattler where it should be.
|
07-09-2020, 01:17 PM | #14 |
Senior Member
|
Re: Timing and hand throttle levers
The next guy to get that car will want that lever in place.
|
07-09-2020, 01:21 PM | #15 |
Senior Member
Join Date: Apr 2018
Location: Mebane NC
Posts: 2,355
|
Re: Timing and hand throttle levers
|
07-11-2020, 12:00 PM | #16 |
BANNED
Join Date: Dec 2019
Posts: 1,196
|
Re: Timing and hand throttle levers
|
07-11-2020, 08:49 AM | #17 |
Senior Member
Join Date: Mar 2019
Location: Sweden
Posts: 145
|
Re: Timing and hand throttle levers
Tried the "drill a dimple in the end-method" and that did the trick, lever is in.
|
07-11-2020, 01:28 PM | #18 |
Senior Member
Join Date: Mar 2019
Location: Sweden
Posts: 145
|
Re: Timing and hand throttle levers
I'm not planning on selling the car because this is something I've been dreaming of building for a very long time, so I'll take my chances and ditch the spark rod and just keeping the hand throttle.
|
|
|
Sponsored Links (Register now to hide all advertisements) |
|