Go Back   The Ford Barn > General Discussion > Model A (1928-31)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 10-20-2019, 07:16 PM   #1
Straw530
Junior Member
 
Join Date: Aug 2019
Posts: 22
Default Model A backfire, can't move

Still new to Model A's, and am having an issue, so I thought I would check with you guys to see if there is an obvious answer. I drove the car today on a little trip about 50 miles each way. Ran good until I was a couple of miles from home, and it started to sputter, and then backfire. It finally got so bad, that I had to pull it home. I had just put the manifold back on with a new gasket after having it planed. I had adjusted the points to .20, and put in new plugs and a coil. To me, it is acting very lean, but I have fuel at the carb and the glass in line filter is full. Is it ignition? I did notice when I adjusted the points, that they seem too closed. I had to open them up to get to .20. Could the points be bad? I am not very good with ignition either! Thanks in advance.
Straw530 is offline   Reply With Quote
Old 10-20-2019, 07:31 PM   #2
garyjohn
Senior Member
 
Join Date: May 2012
Location: Big Pine,CA
Posts: 159
Default Re: Model A backfire, can't move

did you have the gav open enough to get enough fuel in the carb
garyjohn is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 10-20-2019, 08:25 PM   #3
jm29henry
Senior Member
 
jm29henry's Avatar
 
Join Date: Sep 2010
Location: michigan
Posts: 1,126
Default Re: Model A backfire, can't move

I believe you might have a bad condenser cheep fix it just happens
jm29henry is offline   Reply With Quote
Old 10-20-2019, 08:28 PM   #4
Purdy Swoft
Senior Member
 
Purdy Swoft's Avatar
 
Join Date: May 2010
Location: Alabama
Posts: 8,099
Default Re: Model A backfire, can't move

I'm wondering if the problem is modern points and condenser

The foreign condensers that most offer for use with V8 points are not very reliable

I notice that the list of parts that you replaced doesn't include the condenser .

My guess is a bad condenser .
Purdy Swoft is offline   Reply With Quote
Old 10-21-2019, 05:08 AM   #5
Floats
Senior Member
 
Floats's Avatar
 
Join Date: Dec 2013
Location: Mossel Bay, about 300km from Cape Town
Posts: 530
Default Re: Model A backfire, can't move

Have you retorqued the manifold?
__________________
Regards
Chris
Cape Town
28 Model A RPU, 29 Chevy Phaeton, 67 E Type FHC, 67 250SL Pagoda, 83 911 SC
Floats is offline   Reply With Quote
Old 10-21-2019, 05:32 AM   #6
Straw530
Junior Member
 
Join Date: Aug 2019
Posts: 22
Default Re: Model A backfire, can't move

Sponsored Links (Register now to hide all advertisements)
I did retorque the manifold after a short drive. (Once it had cooled again) Are the points and condenser for this something I can get at the parts store, or do I need to go to a Model a site to get the? Thank you
Straw530 is offline   Reply With Quote
Old 10-21-2019, 05:43 AM   #7
Patrick L.
Senior Member
 
Patrick L.'s Avatar
 
Join Date: May 2010
Location: Largo Florida
Posts: 7,225
Default Re: Model A backfire, can't move

You'll probably have to go to a Model A site to get your parts, especially if they are original type points/condenser. Modern type points/condenser are Ford V8 and could be bought/ordered from a good parts store. [ get the expensive ones].

My original thought was fuel delivery, did you try opening the fuel cap ? It could be a venting issue. Actually it could be several issues, which have been covered.
Patrick L. is offline   Reply With Quote
Old 10-21-2019, 07:06 AM   #8
chap52
Senior Member
 
chap52's Avatar
 
Join Date: Jun 2013
Location: Marana Arizona
Posts: 1,771
Default Re: Model A backfire, can't move

Had a similar adventure and found that my gas cap vent wasn't working. This will cause the car to backfire, sputter and stop because fuel cannot flow due to a vacuum condition in the fuel tank.
When this happens open your gas cap and if you hear a "swish" of air it is plugged. Put the cap back on loosely and drive home. I was 50 miles from home and it ran well all the way back.
You can use a small piece of wire to determine if the vent in the cap is clear. I also drilled another hole in mine just in case... Chap
chap52 is offline   Reply With Quote
Old 10-21-2019, 07:20 AM   #9
Fhane
Senior Member
 
Fhane's Avatar
 
Join Date: May 2010
Location: Stuart Florida
Posts: 147
Default Re: Model A backfire, can't move

Check the water in the radiator. It’s may have overheated.
Fhane is offline   Reply With Quote
Old 10-21-2019, 09:45 AM   #10
Keith True
Senior Member
 
Keith True's Avatar
 
Join Date: May 2010
Location: Epping N.H.
Posts: 2,969
Default Re: Model A backfire, can't move

Is there a main fuse in the system? If you are running a stock generator and cutout,and that blows,the generator will put out up to 40 volts,that will give you some pretty spectacular backfires.
Keith True is offline   Reply With Quote
Old 10-21-2019, 10:06 AM   #11
Big hammer
Senior Member
 
Join Date: Jun 2014
Location: Land of Lincoln
Posts: 3,114
Default Re: Model A backfire, can't move

Quote:
Originally Posted by Straw530 View Post
Still new to Model A's, and am having an issue, so I thought I would check with you guys to see if there is an obvious answer. I drove the car today on a little trip about 50 miles each way. Ran good until I was a couple of miles from home, and it started to sputter, and then backfire. It finally got so bad, that I had to pull it home. I had just put the manifold back on with a new gasket after having it planed. I had adjusted the points to .20, and put in new plugs and a coil. To me, it is acting very lean, but I have fuel at the carb and the glass in line filter is full. Is it ignition? I did notice when I adjusted the points, that they seem too closed. I had to open them up to get to .20. Could the points be bad? I am not very good with ignition either! Thanks in advance.
You have fuel at the carb, check if fuel is in the carb. Remove the carb drain to see if you have fuel flowing through!
__________________
Don't force it with a little hammer tap, tap, tap
get a bigger hammer tap done
Big hammer is online now   Reply With Quote
Old 10-21-2019, 06:52 PM   #12
Straw530
Junior Member
 
Join Date: Aug 2019
Posts: 22
Default Re: Model A backfire, can't move

I did take the plug out of the bowl. I had fuel flowing steady there. I did not check the cap, but I will try that as well. Wish I didn't have to work so I could do more on it!
Straw530 is offline   Reply With Quote
Old 10-22-2019, 01:59 PM   #13
1931 flamingo
Senior Member
 
1931 flamingo's Avatar
 
Join Date: May 2010
Location: new britain,ct 06052
Posts: 9,389
Default Re: Model A backfire, can't move

Funny how "work" gets in the way of our personnel lives, even when retired.
Paul in CT
1931 flamingo is offline   Reply With Quote
Old 10-22-2019, 04:47 PM   #14
1crosscut
Senior Member
 
1crosscut's Avatar
 
Join Date: Feb 2011
Location: Lincoln, Nebraska
Posts: 1,905
Default Re: Model A backfire, can't move

Quote:
Originally Posted by Straw530 View Post
Still new to Model A's, and am having an issue, so I thought I would check with you guys to see if there is an obvious answer. I drove the car today on a little trip about 50 miles each way. Ran good until I was a couple of miles from home, and it started to sputter, and then backfire. It finally got so bad, that I had to pull it home. I had just put the manifold back on with a new gasket after having it planed. I had adjusted the points to .20, and put in new plugs and a coil. To me, it is acting very lean, but I have fuel at the carb and the glass in line filter is full. Is it ignition? I did notice when I adjusted the points, that they seem too closed. I had to open them up to get to .20. Could the points be bad? I am not very good with ignition either! Thanks in advance.
Had a situation like yours once. The gap in the block that holds the movable points didn't have a large enough of a gap to allow it to squeeze the movable point enough to hold it in place. I had to remove the movable point and sand the gap larger to allow it to squeeze the movable point so it wouldn't move. So if you check your point gap again and it is not right check the gap in the point block.
__________________
Dave / Lincoln Nebraska
1crosscut is offline   Reply With Quote
Old 10-22-2019, 05:48 PM   #15
Straw530
Junior Member
 
Join Date: Aug 2019
Posts: 22
Default Re: Model A backfire, can't move

Thank you. Not totally sure I follow, but I will check it out. Especially if the points are off again. I did order points and condenser for it as well.
Straw530 is offline   Reply With Quote
Old 10-22-2019, 07:36 PM   #16
1crosscut
Senior Member
 
1crosscut's Avatar
 
Join Date: Feb 2011
Location: Lincoln, Nebraska
Posts: 1,905
Default Re: Model A backfire, can't move

Sorry I didn't explain that too clearly.
Basically if the contact point that screws in and out of to make the adjustment can't be clamped down on hard enough to hold it in place you will need to remove some material in the slot of the part that holds it to give it more room to squeeze down on it.
Clear as mud I'm sure.
__________________
Dave / Lincoln Nebraska
1crosscut is offline   Reply With Quote
Old 10-23-2019, 10:54 AM   #17
katy
Senior Member
 
katy's Avatar
 
Join Date: Jun 2015
Location: Red Deer, Alberta
Posts: 5,011
Default Re: Model A backfire, can't move

I had a problem w/a new B distributor cam that had a rough surface and wore the points rubbing block down quite quickly. I never thought to inspect the cam when I installed it, just assumed it was as smooth as it should have been.
__________________
If you don't hear a rumor by 10 AM, start one!.
Got my education out behind the barn!
katy is offline   Reply With Quote
Old 10-23-2019, 11:05 AM   #18
Purdy Swoft
Senior Member
 
Purdy Swoft's Avatar
 
Join Date: May 2010
Location: Alabama
Posts: 8,099
Default Re: Model A backfire, can't move

Stipe machine offers the best and most acurate distributor cam on the market for the model A and B engines .
Purdy Swoft is offline   Reply With Quote
Old 10-23-2019, 05:04 PM   #19
Patrick L.
Senior Member
 
Patrick L.'s Avatar
 
Join Date: May 2010
Location: Largo Florida
Posts: 7,225
Default Re: Model A backfire, can't move

If this monster still won't start I'd suggest a compression check. I'm wondering if a back fire happens to damage the cam gear.
Patrick L. is offline   Reply With Quote
Old 10-24-2019, 05:45 AM   #20
Straw530
Junior Member
 
Join Date: Aug 2019
Posts: 22
Default Re: Model A backfire, can't move

I was actually wondering about that cam gear, because I had to open up the points to gap them. I was wondering if it was wearing down. I just need to get in the shop! Stupid work!
Thanks again for the ideas
Straw530 is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 09:22 AM.