Go Back   The Ford Barn > General Discussion > Model A (1928-31)

Sponsored Links (Register now to hide all advertisements)

Reply
 
Thread Tools Display Modes
Old 05-05-2013, 06:52 PM   #1
duffer
Senior Member
 
duffer's Avatar
 
Join Date: Aug 2012
Location: clinton township michigan
Posts: 273
Default Edison Car update from Gilmore Museum

Here are more pics of the engine , and the story from the gentleman guarding the car is Ford gave the car to Edison as a gift and Edison saw the car and said he wanted a convertible so Ford told him to drive it to the factory and he took the body off the frame and put the convertible body on the same frame..He said this IS most defiantly the A-1 engine. In one of the pictures you can see Edison getting his car.I took a lot of detail pictures of the car that i will post later tomorrow.
Attached Images
File Type: jpg 101_3170.jpg (76.7 KB, 543 views)
File Type: jpg 101_3141.jpg (88.9 KB, 547 views)
File Type: jpg 101_3130.jpg (80.1 KB, 576 views)
File Type: jpg 101_3168.jpg (36.5 KB, 530 views)
duffer is offline   Reply With Quote
Old 05-05-2013, 07:02 PM   #2
Joe K
Senior Member
 
Joe K's Avatar
 
Join Date: Jul 2010
Location: Cow Hampshire
Posts: 4,175
Default Re: Edison Car update from Gilmore Museum

Except for the radiator shroud and the number, it could be my March 29 Pickup.

That is a two tooth steering I see isn't it?

Joe K
__________________
Shudda kept the horse.
Joe K is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 05-05-2013, 07:06 PM   #3
Mitch//pa
BANNED
 
Join Date: May 2010
Location: Bucks County, PA
Posts: 11,454
Default Re: Edison Car update from Gilmore Museum

whats up with the upper hose worm clamp
Mitch//pa is offline   Reply With Quote
Old 05-05-2013, 07:33 PM   #4
spdway1
Senior Member
 
spdway1's Avatar
 
Join Date: Feb 2011
Location: Chicopee, MA
Posts: 1,380
Default Re: Edison Car update from Gilmore Museum

I would think there would be MORE effort and time put into the engine and compartment, detailing it and making some affordable correct changes see it is all about being #A1.
spdway1 is offline   Reply With Quote
Old 05-05-2013, 07:49 PM   #5
Tom Wesenberg
Senior Member
 
Tom Wesenberg's Avatar
 
Join Date: May 2010
Location: Mpls, MN
Posts: 27,582
Default Re: Edison Car update from Gilmore Museum

I wonder how many years Edison drove it, and wonder what the history is after he quit driving it?

I see many changes from original:
Glass sediment bulb
Copper fuel line
2 tooth steering
Later starter and switch
Later hose clamps
Later ignition cable (too long)
Later dip stick

Last edited by Tom Wesenberg; 05-05-2013 at 08:54 PM.
Tom Wesenberg is offline   Reply With Quote
Old 05-05-2013, 07:55 PM   #6
Drive Shaft Dave
Senior Member
 
Join Date: Dec 2011
Location: New hope Minnesota
Posts: 742
Default Re: Edison Car update from Gilmore Museum

Sponsored Links (Register now to hide all advertisements)
Ya, that was the first thing I saw was the worm clamp.
Drive Shaft Dave is offline   Reply With Quote
Old 05-05-2013, 08:01 PM   #7
BRENT in 10-uh-C
Senior Member
 
BRENT in 10-uh-C's Avatar
 
Join Date: May 2010
Location: Eastern Tennessee
Posts: 11,486
Default Re: Edison Car update from Gilmore Museum

Sure does make one wonder about the credibility of it being A1 when we look at all the incorrect items now doesn't it!!???

.
__________________
.

BRENT in 10-uh-C
.
www.model-a-ford.com
...(...Finally Updated!! )

.
BRENT in 10-uh-C is offline   Reply With Quote
Old 05-05-2013, 08:06 PM   #8
1931 flamingo
Senior Member
 
1931 flamingo's Avatar
 
Join Date: May 2010
Location: new britain,ct 06052
Posts: 9,389
Default Re: Edison Car update from Gilmore Museum

Or, how original is original???
Paul in CT
1931 flamingo is offline   Reply With Quote
Old 05-05-2013, 08:16 PM   #9
Joe K
Senior Member
 
Joe K's Avatar
 
Join Date: Jul 2010
Location: Cow Hampshire
Posts: 4,175
Default Re: Edison Car update from Gilmore Museum

Steve Ciccalone's take on it at http://www.fordbarn.com/forum/showpo...97&postcount=4 was

Quote:
The so called A1 car in Dearborn is a fabrication. The previous owner of A189 (Sen. Charlie Bass) had sufficient stroke to get the body of A1 removed at the museum. It is a '29 chassis with the bogus engine as Gary previously indicated here.
What I see is consistent with this thought. Probably has a black steering wheel?

Thinking further, the Edison "Festival of Light" occurred at Dearborn on October 21, 1929. It may be that the car No. 1 in it's converted/remade version was given to Edison at that time.

I would be curious to know if "spacer pads" were used under the radiator mounts which would definitely date the chassis as a late 29.

Did anyone come up with any other pix/dates of the stamping of Engine No. 1? I've seen several, can't find them now online.

Joe K
__________________
Shudda kept the horse.

Last edited by Joe K; 05-05-2013 at 08:24 PM.
Joe K is offline   Reply With Quote
Old 05-05-2013, 08:28 PM   #10
al's28/33
Senior Member
 
al's28/33's Avatar
 
Join Date: Jun 2010
Location: Redwood City, CA
Posts: 1,588
Default Re: Edison Car update from Gilmore Museum

too bad that it did not recieve the attention it should have gotten.
__________________
1928 "A" Phaeton (mid year with many early features)
1933 "V8" Closed-Cab Pickup Truck
(originally a Model B, 4 Cylinder dating to May, 1933)
al's28/33 is offline   Reply With Quote
Old 05-05-2013, 08:43 PM   #11
spdway1
Senior Member
 
spdway1's Avatar
 
Join Date: Feb 2011
Location: Chicopee, MA
Posts: 1,380
Default Re: Edison Car update from Gilmore Museum

So is the car misrepresented in the Meseum?
spdway1 is offline   Reply With Quote
Old 05-05-2013, 09:01 PM   #12
Tom Wesenberg
Senior Member
 
Tom Wesenberg's Avatar
 
Join Date: May 2010
Location: Mpls, MN
Posts: 27,582
Default Re: Edison Car update from Gilmore Museum

I knew I forgot something in the picture. I just added DIPSTICK to my list above.
Tom Wesenberg is offline   Reply With Quote
Old 05-05-2013, 09:03 PM   #13
Joe K
Senior Member
 
Joe K's Avatar
 
Join Date: Jul 2010
Location: Cow Hampshire
Posts: 4,175
Default Re: Edison Car update from Gilmore Museum

Quote:
Originally Posted by spdway1 View Post
So is the car misrepresented in the Meseum?
Probably not. It is the car that Ford gave to Edison.

Joe K
__________________
Shudda kept the horse.
Joe K is offline   Reply With Quote
Old 05-05-2013, 09:13 PM   #14
Phil
Senior Member
 
Phil's Avatar
 
Join Date: May 2010
Location: Bethany, Ok
Posts: 382
Default Re: Edison Car update from Gilmore Museum

Doesn't have the early starter switch. I guess if it was driven a lot these items may have been changed as maintenance. Wonder how many miles the odometer shows?
Phil is offline   Reply With Quote
Old 05-05-2013, 09:36 PM   #15
Tudortomnz
Senior Member
 
Tudortomnz's Avatar
 
Join Date: May 2010
Location: Canterbury, New Zealand
Posts: 1,242
Default Re: Edison Car update from Gilmore Museum

Also it has the later alloy water pump shaft nut. But the important thing to remember is that the car has an important historic connection between Henry Ford & Thomas Edison & it has the A1 stamped engine.
The real original cars are few indeed; probably the late Dave Lopes '29 Fordor & that 1930 Town Sedan found awhile ago [ featured on FB] with about 1000 miles on it & the delivery sticker still on the windshield.
Tudortomnz is offline   Reply With Quote
Old 05-05-2013, 09:43 PM   #16
Gary WA
Senior Member
 
Gary WA's Avatar
 
Join Date: May 2010
Location: Clinton,WA/Whidbey Island
Posts: 4,088
Default Re: Edison Car update from Gilmore Museum

Quote:
Originally Posted by Tom Wesenberg View Post
I knew I forgot something in the picture. I just added DIPSTICK to my list above.
Hoses?Ignition cable clamp? and cable?
__________________
www.whidbeymodelaclub.com
Gary WA is offline   Reply With Quote
Old 05-05-2013, 09:46 PM   #17
John Duden
Senior Member
 
John Duden's Avatar
 
Join Date: Jun 2010
Posts: 1,854
Default Re: Edison Car update from Gilmore Museum

i think it has the "newer" closed box engine mounts?
John
John Duden is offline   Reply With Quote
Old 05-05-2013, 09:47 PM   #18
jkcrosson
Senior Member
 
jkcrosson's Avatar
 
Join Date: Jan 2011
Location: Pell City AL
Posts: 720
Default Re: Edison Car update from Gilmore Museum

Quote:
Originally Posted by Tudortomnz View Post
1930 Town Sedan found awhile ago [ featured on FB] with about 1000 miles on it & the delivery sticker still on the windshield.
Can you post a link to that discussion. I do not remember it.
__________________
Jamie Crosson
1929 Tudor
Looking for an Original 888 Key
jkcrosson is offline   Reply With Quote
Old 05-05-2013, 10:02 PM   #19
LukeDahlinger
BANNED
 
Join Date: Dec 2010
Posts: 956
Default Re: Edison Car update from Gilmore Museum

Remember the car was updated over the years by Henry Ford, it was returned to Henry Ford in the '30s by Mina Edison.

I think the car underwent an amateur restoration in the 1970s. I remember reading about it in an old 1970s issue of Model A News. Perhaps this helps explain alot of the inconsistencies.

I have seen photos of Edison's Phaeton down in the Everglades in the book "The Edisons of Fort Myers" by Tom Smoot. A very elderly friend of mine who worked for the Ford dealer in Fort Myers told me of having to go pick up this Phaeton and later Mina Edison's '35 Ford for service when he first started working there. My friend is no longer living. Wish I had picked his brain some more.
__________________
Wanted- Feb. 1931 Parts Price List
www.vintagefordfacts.blogspot.com
LukeDahlinger is offline   Reply With Quote
Old 05-05-2013, 10:32 PM   #20
Ron in Quincy
Senior Member
 
Ron in Quincy's Avatar
 
Join Date: May 2010
Location: Quincy, CA.
Posts: 1,708
Default Re: Edison Car update from Gilmore Museum

In addition to the error items previously mentioned, I noticed it has the 2nd generation fan schroud and the 2nd generation hood sills which do not match the early cowl. It also appears to have a 3 brush powerhouse generator with top mount cutout and painted cover?

Ron
Ron in Quincy is offline   Reply With Quote
Old 05-06-2013, 12:59 AM   #21
Tudortomnz
Senior Member
 
Tudortomnz's Avatar
 
Join Date: May 2010
Location: Canterbury, New Zealand
Posts: 1,242
Default Re: Edison Car update from Gilmore Museum

Quote:
Originally Posted by jkcrosson View Post
Can you post a link to that discussion. I do not remember it.
It came up last year, it had just been hauled out of a garage. someone had pulled the engine & trans but all there with 1938 plates from memory. The new owner was going to replace the fenders which were badly rusted, but leave everything else as is.
Sorry, I do not know how to search it, but someone must remember this post with a series of photos from last year.
Tudortomnz is offline   Reply With Quote
Old 05-06-2013, 06:36 AM   #22
jkcrosson
Senior Member
 
jkcrosson's Avatar
 
Join Date: Jan 2011
Location: Pell City AL
Posts: 720
Default Re: Edison Car update from Gilmore Museum

Quote:
Originally Posted by Tudortomnz View Post
It came up last year, it had just been hauled out of a garage. someone had pulled the engine & trans but all there with 1938 plates from memory. The new owner was going to replace the fenders which were badly rusted, but leave everything else as is.
Sorry, I do not know how to search it, but someone must remember this post with a series of photos from last year.

It's the car that Wick found in DC. I do remember it now.
__________________
Jamie Crosson
1929 Tudor
Looking for an Original 888 Key
jkcrosson is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 05-06-2013, 09:50 AM   #23
d.j. moordigian
Senior Member
 
d.j. moordigian's Avatar
 
Join Date: May 2010
Location: Fresno, Ca.
Posts: 3,636
Default Re: Edison Car update from Gilmore Museum

Quote:
Originally Posted by Ron in Quincy View Post
In addition to the error items previously mentioned, I noticed it has the 2nd generation fan schroud and the 2nd generation hood sills which do not match the early cowl. It also appears to have a 3 brush powerhouse generator with top mount cutout and painted cover?

Ron
Ron, you missed the Distributor advance arm...second style.
I also was curious about the firewall....second or third style?
Tom, Steve and I had a quick talk about the "body number"...
whats the body number??
d.j. moordigian is offline   Reply With Quote
Old 05-06-2013, 03:06 PM   #24
duffer
Senior Member
 
duffer's Avatar
 
Join Date: Aug 2012
Location: clinton township michigan
Posts: 273
Default Re: Edison Car update from Gilmore Museum

The gentleman at the museum also said that when the next greatest thing came out for the cars Ford would always tell Edison to come back in and get the up grades on his car.Maybe that explains the add ons on the car.
duffer is offline   Reply With Quote
Old 05-06-2013, 04:03 PM   #25
Mitch//pa
BANNED
 
Join Date: May 2010
Location: Bucks County, PA
Posts: 11,454
Default Re: Edison Car update from Gilmore Museum

Quote:
Originally Posted by duffer View Post
The gentleman at the museum also said that when the next greatest thing came out for the cars Ford would always tell Edison to come back in and get the up grades on his car.Maybe that explains the add ons on the car.
i dont think that is the case here. it looks like its been repaired over the years by someone in the back alley with jc whittney parts
very disappointing

Last edited by Mitch//pa; 05-06-2013 at 04:15 PM.
Mitch//pa is offline   Reply With Quote
Old 05-06-2013, 04:25 PM   #26
Franchise_24
Senior Member
 
Franchise_24's Avatar
 
Join Date: May 2010
Location: Lexington, Ohio
Posts: 782
Default Re: Edison Car update from Gilmore Museum

Sponsored Links (Register now to hide all advertisements)
Quote:
Originally Posted by Mitch//pa View Post
i dont think that is the case here. it looks like its been repaired over the years by someone in the back alley with jc whittney parts
very disappointing

What's disappointing about it? The main thing here is to show engine A1, not all the wrong add-ons that everyone has nit picked over.
__________________
1929 Model A Ford Coupe
Franchise_24 is offline   Reply With Quote
Old 05-06-2013, 06:11 PM   #27
d.j. moordigian
Senior Member
 
d.j. moordigian's Avatar
 
Join Date: May 2010
Location: Fresno, Ca.
Posts: 3,636
Default Re: Edison Car update from Gilmore Museum

Quote:
Originally Posted by Franchise_24 View Post
What's disappointing about it? The main thing here is to show engine A1, not all the wrong add-ons that everyone has nit picked over.
I don't think some of us are nit picken. There are some things that just
don't add-up...if you go by the photo of Henry Ford stamping the block
and the date in the photo. If you look at some of the questions asked
about the engine number pad(size) and others, trying too figure out when
the engine and car was built....that's all.
* But the pad is the "key" too the engine date.*

Dudley
d.j. moordigian is offline   Reply With Quote
Old 05-06-2013, 06:26 PM   #28
Mitch//pa
BANNED
 
Join Date: May 2010
Location: Bucks County, PA
Posts: 11,454
Default Re: Edison Car update from Gilmore Museum

Quote:
Originally Posted by Franchise_24 View Post
What's disappointing about it? The main thing here is to show engine A1, not all the wrong add-ons that everyone has nit picked over.
i am dissapointed of how the car was taken care of and maintained and thats just from 1 engine pic. a car of that stature and place in history to be put on display looking like that is ashame. the least someone could have done was put proper clamps, fuel line etc back on. in my opinion the A1 goes along with the rest of the car.
Mitch//pa is offline   Reply With Quote
Old 05-07-2013, 12:08 AM   #29
Mike V. Florida
Senior Member
 
Mike V. Florida's Avatar
 
Join Date: May 2010
Location: South Florida
Posts: 14,054
Send a message via AIM to Mike V. Florida
Default Re: Edison Car update from Gilmore Museum

Trying to determine what might have added after the Edisons owned it in my opinion is not nit picking.
__________________
What's right about America is that although we have a mess of problems, we have great capacity - intellect and resources - to do some thing about them. - Henry Ford II
Mike V. Florida is offline   Reply With Quote
Old 05-07-2013, 07:48 AM   #30
Steve Plucker
BANNED
 
Join Date: May 2010
Location: Walla Walla, Washington USA
Posts: 6,066
Default Re: Edison Car update from Gilmore Museum

Quote:
Originally Posted by Mitch//pa View Post
i dont think that is the case here. it looks like its been repaired over the years by someone in the back alley with jc whittney parts
very disappointing
And with a 1929 frame as a previous post has said?

What is the LENGTH of the engine number pad?

Pluck
Steve Plucker is offline   Reply With Quote
Old 05-07-2013, 09:38 AM   #31
29ModelA
Senior Member
 
29ModelA's Avatar
 
Join Date: Jun 2010
Location: Owosso, MI
Posts: 673
Default Re: Edison Car update from Gilmore Museum

Quote:
Originally Posted by Mike V. Florida View Post
Trying to determine what might have added after the Edisons owned it in my opinion is not nit picking.
As many years as he had it, much could have been put on when Edison owned it. I am sure the car was not serviced ONLY at a ford factory. Aftermarket replacements surely would have been put on as parts wear.
__________________
1929 Model A Barn find. California car, just a few more parts to find.

Interior, steering box (rebuild), and I am sure much more!
29ModelA is offline   Reply With Quote
Old 06-13-2013, 07:13 PM   #32
Hyperion
Junior Member
 
Hyperion's Avatar
 
Join Date: Jun 2012
Posts: 8
Default Re: Edison Car update from Gilmore Museum

Taken at the Grand Opening:

Hyperion is offline   Reply With Quote
Old 06-13-2013, 08:19 PM   #33
John Duden
Senior Member
 
John Duden's Avatar
 
Join Date: Jun 2010
Posts: 1,854
Default Re: Edison Car update from Gilmore Museum

would be kinda neat with EDISON sparkplugs?
John Duden is offline   Reply With Quote
Old 06-14-2013, 09:10 AM   #34
John LaVoy
Senior Member
 
John LaVoy's Avatar
 
Join Date: May 2010
Location: Rocklin, CA
Posts: 1,219
Default Re: Edison Car update from Gilmore Museum

The car was presented to Edison as a tudor sedan. He brought it back and asked it to be changed to an open car which Ford did. They continued to modify the car as improvements were made. The car was owned by the Edison family until 1939 I believe and given to Ford at that time. It was not well cared for in the beginning. We had to spend several thousands of dollars getting it ready to go on display in the museum. I know there are a number of "things" wrong with it, but they were changed by Ford for his friend. This is a great loan to the museum by Ford Motor Company and I hope people appreciate the role this car played in history.
John LaVoy is offline   Reply With Quote
Old 06-14-2013, 09:59 AM   #35
jkelsh
Senior Member
 
jkelsh's Avatar
 
Join Date: Aug 2010
Location: Westlake Ohio
Posts: 107
Default Re: Edison Car update from Gilmore Museum

I thought Edison's widow donated it to the Henry Ford museum in 1943? I'm probably wrong. I also read somewhere it had a goatskin interior installed instead of the artificial leather. Is that true?
jkelsh is offline   Reply With Quote
Old 06-14-2013, 10:10 AM   #36
Big John
Senior Member
 
Join Date: May 2010
Posts: 416
Default Re: Edison Car update from Gilmore Museum

picky, picky picky....... is this fine point competition? How many kudos for possible replacement items through the years?
Big John is offline   Reply With Quote
Old 06-14-2013, 11:20 AM   #37
P.S.
Senior Member
 
Join Date: Jul 2012
Location: Commiefornia (not for long)
Posts: 1,675
Default Re: Edison Car update from Gilmore Museum

I'd rather see the car the way it looked when Edison was actively driving it, or just stopped driving it than to see how it looked before he took posession.

Changes made through time become part of the car's history. It's silly to undo everything done over the years to return the car to what you THINK is original to display it in a museum.
P.S. is offline   Reply With Quote
Old 06-14-2013, 11:35 AM   #38
jkelsh
Senior Member
 
jkelsh's Avatar
 
Join Date: Aug 2010
Location: Westlake Ohio
Posts: 107
Default Re: Edison Car update from Gilmore Museum

Regardless the only people who would've made such changes would've been Edison, his family, or The Henry Ford. And more likely than not I believe it wouldn't have been the latter. So wouldnt it have had to be changes by the Edisons and therefore while not "factory" correct it would be correct to the car. Also it would have had upgrades done at Ford because up until Edison died in late 1931 he regularly had it updated by Ford
jkelsh is offline   Reply With Quote
Old 06-14-2013, 12:40 PM   #39
ctvpa
Senior Member
 
ctvpa's Avatar
 
Join Date: Apr 2012
Location: Massachusetts
Posts: 479
Default Re: Edison Car update from Gilmore Museum




Just a question. To all of those who feel that the Edison car should be removed of the history included in the years of owning, driving and enjoying the car; do you think the car in the above photo should be washed, stripped, repainted, all the extras removed and bring it back to the way it left the factory?
ctvpa is offline   Reply With Quote
Old 06-14-2013, 12:57 PM   #40
P.S.
Senior Member
 
Join Date: Jul 2012
Location: Commiefornia (not for long)
Posts: 1,675
Default Re: Edison Car update from Gilmore Museum

Quote:
Originally Posted by ctvpa View Post


Just a question. To all of those who feel that the Edison car should be removed of the history included in the years of owning, driving and enjoying the car; do you think the car in the above photo should be washed, stripped, repainted, all the extras removed and bring it back to the way it left the factory?

If you're an antique auto restoration shop, or a keyboard-jockey opinionated "know-it-all", then YES.
P.S. is offline   Reply With Quote
Old 06-14-2013, 01:24 PM   #41
jkelsh
Senior Member
 
jkelsh's Avatar
 
Join Date: Aug 2010
Location: Westlake Ohio
Posts: 107
Default Re: Edison Car update from Gilmore Museum

Quote:
Originally Posted by ctvpa View Post



Just a question. To all of those who feel that the Edison car should be removed of the history included in the years of owning, driving and enjoying the car; do you think the car in the above photo should be washed, stripped, repainted, all the extras removed and bring it back to the way it left the factory?
IMOHO Many cars should be left the way they were when they were in daily use, like the one in the picture and the Edison car. Any one read/ see this before;
http://www.hemmings.com/hcc/stories/...e_dreams1.html
jkelsh is offline   Reply With Quote
Old 06-14-2013, 01:48 PM   #42
Gary Karr
Senior Member
 
Gary Karr's Avatar
 
Join Date: Jun 2010
Location: San Diego, CA
Posts: 1,483
Default Re: Edison Car update from Gilmore Museum

I think the Edison Phaeton is a wonderful study just as is. We may never know how all of the changes came about on this car but the fact that it is indeed the Thomas Edison Phaeton is such an important part of Ford history, the Gilmore should be so lucky to have it on loan.
Gary Karr is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Old 06-14-2013, 11:19 PM   #43
Ken Ehrenhofer
Senior Member
 
Join Date: May 2010
Location: Woodstock, Illinois
Posts: 597
Default Re: Edison Car update from Gilmore Museum

Isn't it possible that the engine had trouble over the years and the car would have been taken to a dealer for replacement. The dealer would have replaced the block and stamped the correct number on it????
I think it is a wonderful car and the museum is lucky to have it and we can all have fun picking it apart.......Like we do with all Model A's Right?
Ken Ehrenhofer is offline   Reply With Quote
Old 06-15-2013, 06:21 AM   #44
Richard Wilson
Senior Member
 
Richard Wilson's Avatar
 
Join Date: May 2010
Location: NC
Posts: 908
Default Re: Edison Car update from Gilmore Museum

George Washington's Axe? I think the Edison Model A is a perfect example of a historical Model A as is and should be in the museum. I wouldn't change a thing.
Richard Wilson is offline   Reply With Quote
Old 06-15-2013, 01:42 PM   #45
Ross/Kzoo
Senior Member
 
Ross/Kzoo's Avatar
 
Join Date: May 2010
Location: Richland Mi.
Posts: 1,172
Default Re: Edison Car update from Gilmore Museum

Quote:
Originally Posted by Richard Wilson View Post
George Washington's Axe? I think the Edison Model A is a perfect example of a historical Model A as is and should be in the museum. I wouldn't change a thing.
You've got that right. You have to appreciate it for what it is. I thought that it was great.
Ross/Kzoo is offline   Reply With Quote
Old 06-15-2013, 02:59 PM   #46
Steve Plucker
BANNED
 
Join Date: May 2010
Location: Walla Walla, Washington USA
Posts: 6,066
Default Re: Edison Car update from Gilmore Museum

Sponsored Links (Register now to hide all advertisements)
Quote:
Originally Posted by Ken Ehrenhofer View Post
Isn't it possible that the engine had trouble over the years and the car would have been taken to a dealer for replacement. The dealer would have replaced the block and stamped the correct number on it????
I think it is a wonderful car and the museum is lucky to have it and we can all have fun picking it apart.......Like we do with all Model A's Right?
I do not think Tim is "picking it apart" but wants to know, as I do and a few others, some mysterious things concering the A1 engine block and the photo.

Tim wanted to know what others felt about it so here is my take on it with red thoughts...:

"While attending the Museum's Grand Opening I spent a moment looking at the Edison car. It wasn't long before I had more questions than answers.

For example..... It is my understanding that the very early engine blocks had the engine number pad just above the water return inlet.
True. This makes sense as the Model T for some time.....and at the end of its production.....also had the engine number pad just above the water return inlet. Then sometime still in 1927 the engine number pad for the Model A blocks was moved up and away from the water return port to upper edge of the block. True. This was due to Part Release # 3463 dated October 12, 1927 which indicated: “Moved pad for engine number to top of block and reduced size”; The same PR also indicated: “Reduced size of water outlet (inlet) connection pad to agree with connection”. Here FORD confused the “outlet” with the “inlet”.

So, sometime after October 12, 1927 the change was made in relation to the placement of the engine number pad. Which would have been the 2” inch length size (the pad on the Edison car is 2-3/4” as stated below). However, since FORD must have already made over 633 or so blocks with the lower pad, he then started to assemble the engine with such.

Now, notice the PR date is October 12, 1927! FORD’s records indicate that the first stampings of engines were done on October 20, 1927 with #1. October 21, 1927 was #’s 2-10; October 24, 1927 was #’s 11-40…through November 17, 1927. The 2” pad was used between November 17 and December 3-14, 1927 when the 2-2/1” engine pad was used…Then between December 19-27, 1927 the pad’s length was changed again to 2-3/4” inch in length.

The engine number pads that were just above the water return inlet were machined smooth for both the Model T's, at least the late ones, and the first Model A's. I suspect that the only reason the engine number pads were machined was because they were an integral part of the water inlet casting, which needed to be machined smooth to provide a water tight connection.
I could not agree more with that statement. And, it would have been difficult and not worth the effort to machine only the water inlet face and not the integral engine number pad. My personal view is that the engine number pad was moved up and away from the water inlet opening so as to save machining time and tool wear.....since the engine number pad did not need to be machined. And, the high engine pads were not machined. So very true.

With the foregoing in mind, I wonder why the engine number pad on the Edison car is a high pad at the top of the block......and not down by the water inlet?
Simple…the original engine, A1, which was stamped on October 20, 1927, was replaced with a later engine block that was stamped also with A1. I have been in hot pursuit to find out the size of the engine number pad on the Edison car and after some time, not to mention the “Why do you want it?” questions , I was told by the Gilmore Museum curiotor that the size of that engine number pad is: The measurement for the width (length) of the pad on Edison's car is 2 3/4". This “size” of pad (the fourth 2-3/4” style/size) began to show up on the blocks between December 19 and December 27, 1927 and lasted to January/February 1929 where anywhere between 2820-4408 blocks had been already stamped. This little detail suggests to me that the block in the Edison car is not one of the first blocks produced. Exactly…What else that means is open to conjecture.

I suppose it's possible that the block for the Edison car was still the first one "finished" and stamped number one even though it was not among the early blocks produced. This possibility to me seems to be a bit far fetched
(agreed) since there were hundreds of early low pad blocks produced and stamped with numbers as least as high as three digits. Between A616 (low pad) and A633 (2” high pad) to be exact…the change from low to high was November 17, 1927 (or very close to it). During this time period, FORD was sending all these numberd engines, and other parts to complete the assembly of the Model A, to most, if not all, the asembly plants around the USA so they could get things squared away within their assembly plant to bring it up to full production.

In addition, the picture that depicts Henry and others purportedly stamping engine number one shows a block with the high engine number pad, not low.
True. My guess is that the picture was staged for promotional purposes....and not much attention was paid to details such as the location of the engine number pad. True…My feelings exactly, AND IF the A1 engine which is in the Edison car now is that very engine for which depicts Henry Ford stamping it in the picture, then the photo session must have been done sometime after December 27, 1927 (or there abouts) when the 2-3/4” pad took effect. Whether the pad is smaller than 2-3/4” in length, I do not think we can effectivly tell for sure of the exact size from the photo.

I suppose another possibility is that Ford started stamping the production engines with some number other than one, and then at some point shortly thereafter decided to produce engine number one, take pictures, and then put it in a car for Edison.
I respectly disagree on that assumption as to the fact that we would see something of the sort, number wise, in those early blocks and as to date nothing has shown us that was the fact. And, if this is what happened, the engine number pad might have already been moved up when number one was produced for Edison.



If anyone has any evidence that the engine number pads for the Model A were first high, as is the case with the Edison car as it sits, and then moved down for a while and then moved back up again, please share it.
I to would welcome any such information if it so exists.

Pluck
Steve Plucker is offline   Reply With Quote
Old 06-15-2013, 07:57 PM   #47
duffer
Senior Member
 
duffer's Avatar
 
Join Date: Aug 2012
Location: clinton township michigan
Posts: 273
Default Re: Edison Car update from Gilmore Museum

Thanks for all the info. Pluck...i think the car looks great the way it is. Just to think that Edison once drove that car is priceless ,no matter what condition....I'm sure he took Henry for a ride at some point too.
duffer is offline   Reply With Quote
Old 06-16-2013, 11:42 PM   #48
Richard in Anaheim CA
Senior Member
 
Richard in Anaheim CA's Avatar
 
Join Date: May 2010
Location: Anaheim California
Posts: 551
Default Re: Edison Car update from Gilmore Museum

I was there and I think it belongs there. I have heard Henry had a Model A coupe he drove clear up to the early 40s and it had any number of modifications, some from places like Pep Boys.

If you want to pick something apart, step outside and look at the dog bone shock links on Edsels custom built 29 phaeton.

This is not a MAFCA/MARC fine point judging show. It's a museum and the stories that go with the car are what people enjoy. People don't bid the price of Elvis's scarf into the stratosphere because the scarf is perfect. They bid it up because it has Elvis's sweat on it.

Richard
Anaheim CA
Richard in Anaheim CA is offline   Reply With Quote
Old 07-26-2013, 09:20 PM   #49
ciccalone
Junior Member
 
Join Date: Feb 2013
Posts: 16
Default Re: Edison Car update from Gilmore Museum

Hi everyone, my father, Steve Ciccalone posted this thread about 7 months before his passing in 2011 on a thread for "earliest model a in existence"

"The so called A1 at Greenfield Village is a recreation. The former owner of A189, a US congressman, arranged through Bill Ford to have the body lifted to confirm it was not the real car. From the engine release list, A12, A13 and A14 were the first engines sent to production on 10/23/27. A1 in fact wasn't sent to the line until 11/1/27. A189 is the earliest surviving real engine, having been stamped 11/1/27 but not released to the line until 11/25/27. The earliest surviving engine sent to production is A241, the 82nd, which went on 11/7/27. The next engine is A354 that was the 101st released on 11/8/27. The third surviving engine is A435, also sent on 11/8/27 and was the 123rd released. These numbers come from the engine release log found many years ago by George DeAngelis. Of the known three digit cars, only two, A189 and A616 are bonefide matching number cars with their original bodies, a roadster and tudor respectively. Oddly, both engines were sent to assembly the same day with one engine released between them. I am not aware of any surviving real single or two digit engines. I know or am aware of all the confirmed three digit cars/engines. I own 3 three digit cars, only one of which is matching #s, A189, and a very low matching numbers four digit roadster A1031. My very good friend is restoring, A1276, another matching numbers early vehicle.

Very early cars of great interest to a small group of people, noteably, Doc Kalinka and Mike Gooding, whose father Fred actually got Doc interested about them in the early 1970's. I would be happy to answer any questions about these early A's and I hope this little bit of information helps. We are hoping to get a special interest group started at MARC, which would have been done by now if frankly I hadn't been so lazy."

It just so happens that I may be going to the museum on Thursday this week and I will try to get a picture of the engine pad myself. If anyone wants to search the string I pulled this posting from you can see some very clear engine pictures that my dad posted as well.

Although, like the earlier post states, even if A1 is not the earliest car, it is still a car that has a great story.

Thanks,
Steve Ciccalone
ciccalone is offline   Reply With Quote
Old 07-26-2013, 10:44 PM   #50
dlshady
Senior Member
 
dlshady's Avatar
 
Join Date: Jun 2010
Location: Huntsville, AL
Posts: 538
Default Re: Edison Car update from Gilmore Museum

Quote:
Originally Posted by spdway1 View Post
So is the car misrepresented in the Meseum?
Quote:
Originally Posted by Joe K View Post
Probably not. It is the car that Ford gave to Edison.

Joe K
If this is really the car that was given to Edison, there doesn't appear to be a whole lot of the original car left. I understand that the car given to Edison was upgraded often over the years, but at what point does it cease to be the same car? As an example, consider the brake system. I'd guess that Ford updated the braking system when they went away from the split system, but a "first month of production" frame should be easy enough to spot from a mile away if you know what to look for, even if the brake system has been upgraded. Would Ford have just lifted the body and rolled a new chassis underneath? Possibly, and that might well be what happened. Even if that's the case it should still have a very early body, assuming that it was changed from a Tudor to a Phaeton shortly after it was given to Edison, and again that should be easy enough to spot. And it's pretty obvious that the engine isn't the original A1, so...

Is it misrepresented, as was asked earlier? I don't think intentionally, but it doesn't look like much of it (if any) is actually original to the car that was given to Edison. In fact, I can't pick out a single piece visible in the photos that's Oct. or Nov. 1927 production.
dlshady is offline   Reply With Quote
Old 07-26-2013, 11:20 PM   #51
BILL WILLIAMSON
Senior Member
 
BILL WILLIAMSON's Avatar
 
Join Date: Dec 2010
Location: FRESNO, CA
Posts: 12,560
Default Re: Edison Car update from Gilmore Museum

My own personal viewpoint, many historical things may be a re-creation of, or a facsimilie of, or changed slightly over the years, but at least the history has been "somewhat" preserved for us to appreciate!
I was thrilled when I first knew about Thomas Edison working with Henry Ford as Edison was one of my HEROS, even from grammar school. I love the ingenuity of early pioneers in the transportation field! Bill W.
__________________
"THE ASSISTANT GURU OF STUFF"
BILL WILLIAMSON is offline   Reply With Quote
Old 07-27-2013, 01:51 AM   #52
Tudortomnz
Senior Member
 
Tudortomnz's Avatar
 
Join Date: May 2010
Location: Canterbury, New Zealand
Posts: 1,242
Default Re: Edison Car update from Gilmore Museum

This has been an interesting thread on A1. We know that A1 started as a Tudor ; I recently re found an old photo from an old [1960] Clymer book which shows this Tudor. It also gives a different time line for the Phaeton which may help explain why the Phaeton does not really show as a 1927 Model A today. A lot of the updates could well have been done before Edison got it when it was used & tested by Ford as a Tudor?
Attached Files
File Type: pdf img002.pdf (759.3 KB, 105 views)
Tudortomnz is offline   Reply With Quote
Old 07-27-2013, 06:41 AM   #53
Phil
Senior Member
 
Phil's Avatar
 
Join Date: May 2010
Location: Bethany, Ok
Posts: 382
Default Re: Edison Car update from Gilmore Museum

In the pic from above, with Edsel and Henry in that Mr and Mrs Edison?
Phil is offline   Reply With Quote
Old 07-27-2013, 12:30 PM   #54
Gary Karr
Senior Member
 
Gary Karr's Avatar
 
Join Date: Jun 2010
Location: San Diego, CA
Posts: 1,483
Default Re: Edison Car update from Gilmore Museum

Steve, thank you for posting your first message on Ford Barn. Your Pop was a great contributor to this site. I had a lot of great conversations with him regarding VE-28 Model A's as I am working on A3261.
Gary Karr is offline   Reply With Quote
Old 07-27-2013, 02:23 PM   #55
modeleh
Senior Member
 
modeleh's Avatar
 
Join Date: May 2010
Location: Nanaimo BC
Posts: 242
Default Re: Edison Car update from Gilmore Museum

Very interesting thread with some amazing detective work and impressive knowledge about the early cars. I would say that we would all be in agreement that the car was no doubt owned and used by Edison, I do support the effort to authenticate and validate artifacts to ensure accurate representation.
If the engine was disproved as being authentically A1 and perhaps a restamped replacement, I don't believe it hurts the historical importance of the car.
modeleh is offline   Reply With Quote
Old 07-27-2013, 09:10 PM   #56
Chris Haynes
Senior Member
 
Chris Haynes's Avatar
 
Join Date: May 2010
Location: Camarillo, CA and Pine Grove, CA
Posts: 2,830
Default Re: Edison Car update from Gilmore Museum

Perhaps on one of the cars visits to the factory the body was put on a newer chassis?
__________________
1921 Runabout
1930 Tudor
Early 1930 AA
Speed costs money. How fast do you want to go?
Chris Haynes is offline   Reply With Quote
Old 07-27-2013, 09:55 PM   #57
jetrod
Member
 
Join Date: May 2010
Location: Central NC
Posts: 67
Default Re: Edison Car update from Gilmore Museum

Gentlemen, I'm late to this discussion, but I have something to add. I was raised in the downriver area of Mi. and as a young person visited the Henry Ford museun many times (in the 50's). I clearly remember the #1 engine, mounted on a rolling motor stand, on display in the museum, The Edison car was also there and both items were singled out and their unique character clearly labled, although the engine was in a different area of the museum. They were displayed like that for many years. Fast forward to the mid 60's, when as a new member of the Motor Cities Chapter, I had the opportunity to do something special. Remember in those days Motor Cities Chapter met in the Greenfield Villiage,and they had a special relationship with The Ford Museum/Greenfield Villiage, and the chapter was sometimes asked to do some things to help out. This time they asked the chapter to UNITE (REUNITE) THE #1 ENGINE WITH THE EDISON PHAETON. I along with about 6 others, on a Saturday morning did that very thing. I knew nothing of the running production changes at that time and can add nothing about any, but that the what the Museum claimed to be the #1 engine and the Edison car were reunited by the Motor Cities Chapter in the mid 60"s.--- Jetrod
jetrod is offline   Reply With Quote
Old 07-27-2013, 11:13 PM   #58
modeleh
Senior Member
 
modeleh's Avatar
 
Join Date: May 2010
Location: Nanaimo BC
Posts: 242
Default Re: Edison Car update from Gilmore Museum

Quote:
Originally Posted by ctvpa View Post



Just a question. To all of those who feel that the Edison car should be removed of the history included in the years of owning, driving and enjoying the car; do you think the car in the above photo should be washed, stripped, repainted, all the extras removed and bring it back to the way it left the factory?
FWIW, the Flyer was restored by Bill Harrah in the early 60s. It never looked like that when he got it. He hired Walt Disney and his crew to replicate how it looked in the photos the day it rolled into Paris. This included breaking and bending the headlamp to duplicate the lamp that got smashed by a pigeon during the race. All the "patina" on the car was done during the restoration by the Disney artists.
Although it is arguably one of the three most important automotive artifacts in the world, it is not what is considered today as a barn find or in "survivor" condition. It was restored to duplicate the look of the car on the final day of the most grueling auto race in history, Bill Harrah is to thank for putting that car in the condition it is today so the world can enjoy it.
modeleh is offline   Reply With Quote
Old 07-28-2013, 12:13 AM   #59
dlshady
Senior Member
 
dlshady's Avatar
 
Join Date: Jun 2010
Location: Huntsville, AL
Posts: 538
Default Re: Edison Car update from Gilmore Museum

Quote:
Originally Posted by modeleh View Post
FWIW, the Flyer was restored by Bill Harrah in the early 60s. It never looked like that when he got it. He hired Walt Disney and his crew to replicate how it looked in the photos the day it rolled into Paris. This included breaking and bending the headlamp to duplicate the lamp that got smashed by a pigeon during the race. All the "patina" on the car was done during the restoration by the Disney artists.
Although it is arguably one of the three most important automotive artifacts in the world, it is not what is considered today as a barn find or in "survivor" condition. It was restored to duplicate the look of the car on the final day of the most grueling auto race in history, Bill Harrah is to thank for putting that car in the condition it is today so the world can enjoy it.
I started to point that out earlier but some folks only hear what they want to hear. For those who are interested, Coker Tires sells an amazing DVD about the history of the Great Race and there's a lot of information about the car itself as well. As I recall, Harrah's commissioned some men back in the late 50's to go out and find this particular car because of it's historical significance, and when they returned with it he flew the original driver, Mr. George Schuster, out to Reno to verify that it was indeed the winning car. When Mr. Schuster arrived he said that the car had been modified so much from when he drove it in 1908 that he was quite firmly convinced it was NOT the same car. Nonetheless, he hung around at Mr. Harrah's request while the car was dismantled, and when they lifted off the body Mr. Schuster spotted a makeshift repair to either the frame or rear axle (I forget which) that he remembered making during the race!
dlshady is offline   Reply With Quote
Old 07-28-2013, 12:37 AM   #60
modeleh
Senior Member
 
modeleh's Avatar
 
Join Date: May 2010
Location: Nanaimo BC
Posts: 242
Default Re: Edison Car update from Gilmore Museum

Correct. It was a stop drill repair to a frame crack that Mr Schuster recognized. Prior to that it was not believed to be the car from the race as it had been altered post race at the Thomas factory and passed through several hands after the company bankruptcy auction, one being the DuPont family.
modeleh is offline   Reply With Quote
Old 07-28-2013, 08:35 PM   #61
ciccalone
Junior Member
 
Join Date: Feb 2013
Posts: 16
Default Re: Edison Car update from Gilmore Museum

Garry, thanks for the note. I'm relatively new to the hobby, but I have found this site to be a great resource.
ciccalone is offline   Reply With Quote
Old 07-29-2013, 03:03 PM   #62
duffer
Senior Member
 
duffer's Avatar
 
Join Date: Aug 2012
Location: clinton township michigan
Posts: 273
Default Re: Edison Car update from Gilmore Museum

Quote:
Originally Posted by jetrod View Post
Gentlemen, I'm late to this discussion, but I have something to add. I was raised in the downriver area of Mi. and as a young person visited the Henry Ford museun many times (in the 50's). I clearly remember the #1 engine, mounted on a rolling motor stand, on display in the museum, The Edison car was also there and both items were singled out and their unique character clearly labled, although the engine was in a different area of the museum. They were displayed like that for many years. Fast forward to the mid 60's, when as a new member of the Motor Cities Chapter, I had the opportunity to do something special. Remember in those days Motor Cities Chapter met in the Greenfield Villiage,and they had a special relationship with The Ford Museum/Greenfield Villiage, and the chapter was sometimes asked to do some things to help out. This time they asked the chapter to UNITE (REUNITE) THE #1 ENGINE WITH THE EDISON PHAETON. I along with about 6 others, on a Saturday morning did that very thing. I knew nothing of the running production changes at that time and can add nothing about any, but that the what the Museum claimed to be the #1 engine and the Edison car were reunited by the Motor Cities Chapter in the mid 60"s.--- Jetrod
Thanks for the input here...I wish i would have had the chance to do something like that.
duffer is offline   Reply With Quote
Sponsored Links (Register now to hide all advertisements)
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Sponsored Links (Register now to hide all advertisements)


All times are GMT -5. The time now is 04:24 PM.